AEG Su 96040 4i Operating Instructions

Installation
11
1xA
2xD
1xB
2xC
2xL
2xE
18xI
2xF2xG
1xK
1
Installation kit+
Two cabinet securing brackets are supplied with the installation pack.
They need to be assembled onto the cabinet prior to cabinet being
pushed into the Kitchen aperture.
+1.To fit these brackets remove the two
screws at the top left and right
hand front corners of the cabinet.
2.Position the two brackets 
as shown in the figure and
replace the two securing
screws.
2
a)
Left hand bracket Right hand bracket2
b)
 

Installation
12
Push the appliance
into place. The plug
socket necessary for
connection of the
appliance to the elec-
tricity supply should 
be positioned, so that
the plug is not placed
in the recess.
3.To adjust the height
proceed as follows:
Loosen or tighten the
two front feet.
The rear feet are adjusted by turning the screw in the front kick plate
to the left or right.
596
555
max
+ -
3
+
-
E
b)
4.The joint cover (B) is to be
assembled after having installed
the appliance in the recess.
If...

7
Installation
13
6.To mount the furniture door
proceed as shown in the fig-
ures:
5.Push the appliance
into place and retain
the cabinet with
screws (I) through the
securing brackets into
the worktop or adja-
cent woodwork as
necessary.
ab
c
C
click
click
8
I
5
a
b
10
12
34C
6
 

Installation
I
27,5 cm27,5 cm
55 cm
10
F
b
==
9
I
c
MšbeltŸr Innenseitea
Upper part of kitchen 
furniture panel
12
3
45°
11= =
10
12
1
2
14
 

90°
115°L
L
15
Installation
15
14
A
8 mm
13
G
K
I
F
7.Refit the covering strip.
 

Installation
16
Fitting the plinth
Important!
For the efficient operation of the appliance, it is important that the
original ventilation grid is used.
¥ For an opening height dimension
A=820 mm and a plinth height
dimension a=100 mm, the plinth may
be fitted without adjustments. The
same applies to an opening height
dimension B=870 mm and a plinth
height dimension b=150 mm.
¥ For plinth heights greater than 
a=100 mm, b=150 mm, a cut should
be made in the plinth, 580 mm wide,
in the centre of the...

Installation
The mains cable may only be changed by a qualified electrician or
competent person. If your appliance needs repairing, please contact
your local AEG Service Force Centre.
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
WARNING Ð THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety mea-
sures not be observed.
Before switching on, make sure the electricity...

18
1 Butter/cheese compartment
2 Sliding shelf
3 Bottle shelf
4 Vegetable drawers
5 Storage shelves
6
Thermostat
7
Freezer compartment
À
Á
 Ã
Ä
Å
Æ
Description of the appliance
View of the appliance
Prior to Initial StartÐUp
Please clean the appliance interior and all accessories prior to initial
start-up (see section: ÒCleaning and CareÓ).+
 

19
Starting up and temperature regulation
Important!Only use the appliance when builtÐin!
+1.Connect the appliance to the mains electricity supply.
When the refrigerator compartment door is opened, the internal light-
ing is switched on.
The temperature control knob is
located on the right hand side of the
refrigerator compartment.
Setting Ò0Ó means:Off.
2.Turn the control knob clockwise past
Ò1Ó. The refrigerating unit is now on
and operates automatically.
Setting Ò1Ó means:
Hightest temperature,...

20
If this happens, turn the thermostat knob back to a warmer setting
(position Ò3Ó to Ò4Ó). At this setting the compressor will be switched on
and off as usual and automatic defrosting recommenced.
Switching off the appliance
To switch off the appliance, turn the temperature regulator to position
0.
If the appliance is not going to be used for an extended period:
+1.Remove all refrigerated and frozen packages.
2.Switch off the appliance by turning the thermostat knob to position
0.
3.Remove the mains...