AEG Su 96040 4i Operating Instructions
Have a look at the manual AEG Su 96040 4i Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation 11 1xA 2xD 1xB 2xC 2xL 2xE 18xI 2xF2xG 1xK 1 Installation kit+ Two cabinet securing brackets are supplied with the installation pack. They need to be assembled onto the cabinet prior to cabinet being pushed into the Kitchen aperture. +1.To fit these brackets remove the two screws at the top left and right hand front corners of the cabinet. 2.Position the two brackets as shown in the figure and replace the two securing screws. 2 a) Left hand bracket Right hand bracket2 b)
Installation 12 Push the appliance into place. The plug socket necessary for connection of the appliance to the elec- tricity supply should be positioned, so that the plug is not placed in the recess. 3.To adjust the height proceed as follows: Loosen or tighten the two front feet. The rear feet are adjusted by turning the screw in the front kick plate to the left or right. 596 555 max + - 3 + - E b) 4.The joint cover (B) is to be assembled after having installed the appliance in the recess. If necessary, pads (E) are supplied for the rear feet to make sliding the appliance in and out of the recess easier. To fit the pads, press them onto the rear feet. If required, the dimensions of these pads can be reduced by breaking them where marked. II52 E B 4 1
7 Installation 13 6.To mount the furniture door proceed as shown in the fig- ures: 5.Push the appliance into place and retain the cabinet with screws (I) through the securing brackets into the worktop or adja- cent woodwork as necessary. ab c C click click 8 I 5 a b 10 12 34C 6
Installation I 27,5 cm27,5 cm 55 cm 10 F b == 9 I c MšbeltŸr Innenseitea Upper part of kitchen furniture panel 12 3 45° 11= = 10 12 1 2 14
90° 115°L L 15 Installation 15 14 A 8 mm 13 G K I F 7.Refit the covering strip.
Installation 16 Fitting the plinth Important! For the efficient operation of the appliance, it is important that the original ventilation grid is used. ¥ For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments. The same applies to an opening height dimension B=870 mm and a plinth height dimension b=150 mm. ¥ For plinth heights greater than a=100 mm, b=150 mm, a cut should be made in the plinth, 580 mm wide, in the centre of the appliance posi- tion, leaving a remaining height of a=100 mm, b=150 mm. ¥ Attach plinth to the kitchen units. Important! The plinth must be positioned at a minimum distance of 25 mm from the door. Please check whether, after installing your appliance and especially after reversing the door, the door seal seals right round. A badly fitting door seal may lead to heavy frosting and result in a higher power con- sumption (see also ÒWhat to do if ...Ó). 008 580 a = 100 b = 150 25 - 80 A = 820 B = 870 25 Power supply A correctly installed, earthed socket is required for the electrical sup- ply. The supply must have a fuse rating of at least 10 Amps. If the socket is not accessible once the appliance is built in, the electrical installation must include suitable means of isolating the appliance from the mains (e.g. a fused spur). Before initial start-up, refer to the appliance rating plate to ascertain if supply voltage and current values correspond with those of the mains at the installation location. e.g.: AC 220 ... 240 V 50 Hz or 220 ... 240 V ~50 Hz (i.e. 220 to 240 volts alternating current, 50 Hertz) The rating plate is inside the appliance on the right. +
Installation The mains cable may only be changed by a qualified electrician or competent person. If your appliance needs repairing, please contact your local AEG Service Force Centre. Electrical Connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING Ð THIS APPLIANCE MUST BE EARTHED The manufacturer declines any liability should these safety mea- sures not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance rating plate. The rating plate is inside, on the right. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved (BS 1362) fuse must be used. Important The wires in the mains lead are coloured in accordance with the following code: Green and Yellow Earth Blue Neutral Brown Live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the termi- nals in your plug, proceed as follows: 1.The wire coloured green and yellow must be connected to the termi- nal marked with the letter ÒEÓ or by the earth symbol or coloured green and yellow. 2.The wire coloured blue must be connected to the terminal marked ÒNÓ or coloured black. 3.The wire coloured brown must be connected to the terminal marked ÒLÓ or coloured red. 4.Upon completion there must be no cut, or stray strands of wire pre- sent and the cord clamp must be secure over the outer sheath. Warning!A cut-off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut-off plug is disposed of safe- ty. 207 GREEN & YELLOW 13 AMP. FUSE BROWN CORD CLAMP BLUE 13 AMP 17
18 1 Butter/cheese compartment 2 Sliding shelf 3 Bottle shelf 4 Vegetable drawers 5 Storage shelves 6 Thermostat 7 Freezer compartment À Á Â Ã Ä Å Æ Description of the appliance View of the appliance Prior to Initial StartÐUp Please clean the appliance interior and all accessories prior to initial start-up (see section: ÒCleaning and CareÓ).+
19 Starting up and temperature regulation Important!Only use the appliance when builtÐin! +1.Connect the appliance to the mains electricity supply. When the refrigerator compartment door is opened, the internal light- ing is switched on. The temperature control knob is located on the right hand side of the refrigerator compartment. Setting Ò0Ó means:Off. 2.Turn the control knob clockwise past Ò1Ó. The refrigerating unit is now on and operates automatically. Setting Ò1Ó means: Hightest temperature, warmest setting. Setting Ò6Ó (end-stop) means: Lowest temperature, coldest setting. Note:From a food safety point of view, +5¡C for the refrigerator com- partment and -18¡C for the freezer compartment should be con- sidered cold enough as a storage temperature. The temperatures in the refrigerator compartment and freezer com- partment cannot be independently regulated. At a low ambient temperature of around 16¡C, setting Ò1Ó should be selected. At ambient temperatures of around 25¡C, select setting Ò2Ó. If you require a lower temperature, select setting Ò3Ó or Ò4Ó. On this setting , you can be sure the fresh food placed in the freezer compart- ment will be reliably frozen and that a storage temperature of -18¡C will be maintained in the freezer compartment. If you want to freeze fresh food rapidly, select setting Ò6Ó, ensuring that the temperature in the refrigerator compartment does not drop below 0¡C. You should also promptly reset the thermostat knob to set- ting Ò3Ó or Ò4Ó after the freezing of the fresh food is complete. Important! High ambient temperatures (e.g. on hot summer days) and a cold set- ting on the thermostat (positionÓ5Ó to Ò6Ó) can cause the compressor to run continuously. Reason: when the ambient temperature is high, the compressor must run continuously to maintain the low temperature in the appliance. The fridge will not be able to defrost since automatic defrosting of the fridge is only possible when the compressor is not running (see also Defrosting section). The result is the build up of a thick layer of frost on the fridge rear wall. AEG62
20 If this happens, turn the thermostat knob back to a warmer setting (position Ò3Ó to Ò4Ó). At this setting the compressor will be switched on and off as usual and automatic defrosting recommenced. Switching off the appliance To switch off the appliance, turn the temperature regulator to position 0. If the appliance is not going to be used for an extended period: +1.Remove all refrigerated and frozen packages. 2.Switch off the appliance by turning the thermostat knob to position 0. 3.Remove the mains plug or switch off or disconnect from the electricity supply. 4.Clean thoroughly (see section: ÒCleaning and CareÓ). 5.Leave the door open to avoid the build up of odours. + Interior Accessories Storage shelves Various glass storage shelves are included with your appliance. The height of the storage shelves can be adjusted: +1.To do this pull the storage shelf for- ward until it can be swivelled upwards or downwards and removed. 2.Please do the same in reverse to insert the shelf at a different height.