AEG Su 86000 1i Installation Instructions

SANTO
ARCTIS
Integrierbare Unterbau-KŸhl- und 
GefriergerŠte
RŽfrigŽrateurs et congŽlateurs sous-plan
ˆ intŽgrer
Ge•ntegreerde onderbouwkoel- en 
vriesapparaten
Integrated built-under refrigerators and 
freezers
Integrerbara underbŠnk-kyl- och frysskŒp
Tyštason alle asennettavat jŠŠkaapit ja 
pakastimet
Frigoriferi e congelatori sottotavolo da 
incasso
kMontageanweisung 2-10
pInstructions de montage 11-19
NMontage-aanwijzing 20-28
tInstallation instructions 29-37
UMonteringsanvisning 38-46
qAsennusohjeet...

Grid preparationt
When changing the side at which the door opens, remove plug from
the mains.
Left door opening:
+Remove the left side (A) of the grid cutting
it from the rear (see figure)
Right door opening:
+Remove the right side (B) of the grid cutting
it from the rear (see figure)
Re-install the grid to the base of the appli-
ance by pushing on to the clasps (a) until
they click.
To reverse the opening direc-
tion of the door, proceed as
shown in the figures:
29
a
a
DO002/2
A
B
Reversing the door
The...

Changing over the freezer compartment door
(not on all models)
30
6
8 7
2
3
10
11 9
1213
Warning! After completion of
the door reversing operation,
check that the door gasket
adheres to the cabinet. If the
ambient temperature is cold
(i.e. in Winter), the gasket
may not fit perfectly to the
cabinet. In that case, wait for
the natural fitting of the
gasket or accelerate this pro-
cess by heating up the part
involved with a normal hair-
dryer on a low setting.
+Open the freezer compartment door a
little...

31
Position the covering cap (M) on the
opposite side.
Turn the freezer compartment door
through 180¡ and fit the lower door
bearing into the lower bearing cavity
of the freezer compartment door.
Lift the freezer compartment door a
little way upwards, fit it into the
upper door bearing, and at the same
time insert the lower door bearing
into the square hole. Small upwards
and downwards adjustments of the
freezer compartment door will make
fitting easier.
+
+
+
AEG43
M
Installation kit
1
1xA
12 1xB
2xC
2...

32
Two cabinet securing brack-
ets are supplied with the
installation pack. They need
to be assembled onto the
cabinet prior to cabinet
being pushed into the
Kitchen aperture.
To fit these brackets remove
the two screws at the top
+
+
Right hand
bracket
1/a
Left hand
bracket
Push the appliance into
place. The plug socket
necessary for connection
of the appliance to the
electricity supply should be
positioned, so that the
plug is not placed in the
recess.
To adjust the height pro-
ceed as follows:
Loosen...

33
Screw appliance into place
5
+The joint cover (B) is to be
assembled after having
installed the appliance in the
recess.
3
12
B
4
11 5°
 

34
Mounting furniture door
7
6
a
b
10
12
34C
8
ab
clic
clic
c C
C
 

35
10
12
3
45
°
11
= =
10
Upper part of kitchen furniture panel
9b a
==
1
2
Lower part of kitchen furniture
panel
9/a
275 275
 max 100
 

36
Refit the covering strip.+
13
A
12
 

37
Fitting the plinth
Important!
For the efficient operation of the appli-
ance, it is important that the original
ventilation grid is used.
¥ For an opening height dimension 
A=820 mm and a plinth height 
dimension a=100 mm, the plinth 
may be fitted without adjustments.
The same applies to an opening 
height dimension B=870 mm and a 
plinth height dimension b=150 mm.
¥ For plinth heights greater than 
a=100 mm, b=150 mm, a cut should 
be made in the plinth, 580 mm wide, 
in the centre of the appliance...