AEG Mixed Hob HD955100NB User Manual

CAUTION!
Make sure that the gas
supply pressure of the
appliance obeys the
recommended values.Rigid connection:
Carry out connection by using metal rigid
pipes (copper with mechanical end).
8.5  Injectors replacement
1.Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the
injectors and replace them with the
ones which are necessary for the type of gas you use (see table in
"Technical Information" chapter).
4. Assemble the parts, follow the...

of clamps fixed to the side of the
cabinet, in order to avoid any contact with the equipment beneath thecooktop.Electrical Requirements
Permanent electrical installation must
agree with the latest I.E.E. Regulations and local Electricity Board regulations.
For your own safety the installation must
be done by a qualified electrician (e.g.
your local Electricity Board, or a
contractor who is on the roll of the
National Inspection Council for Electrical
Installation Contracting [NICEIC]).
The manufacturer...

phase. There must be no cut or stray
strands of wire present. The cord
clamp must be correctly attached to
the outer sheath.8.9  Attaching the seal
1.Clean the worktop around the cut
out area.
2. Attach the supplied seal stripe to the
lower edge of the hob along the
outer edge of the glass ceramic. Do
not extend it. Make sure that the
ends of the seal stripe are located in the middle of one side of the hob.
3. Add some mm when you cut the seal
stripe to the length.
4. Push the two ends of seal stripe...

CAUTION!
Install the appliance only on
a worktop with a flat surface.8.11  Possibilities for insertionKitchen unit with door
The panel installed below the hob must
be easy to remove and let an easy access
in case a technical assistance
intervention is necessary.
A) Removable panel
B) Space for connections
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
www.aeg.com24R 5 mm
min. 55 mm
490  
mm830  
mm
600 mm min. 38 mm min. 2 mm min. 12 mm min.  2...

safety reasons and to let easy remove
oven from the unit.If you install the hob
asymmetrically rightward the
minimum distance between
left edge of the hob and left
support must be 72 mm.9.  TECHNICAL INFORMATION9.1  Hob dimensionsWidth880 mmDepth520 mm9.2 Cooking zones specificationCooking zoneNominal power
(maximum heat
setting) [W]Power function
[W]Power function
maximum dura-
tion [min]Cookware diam-
eter [mm]Left front220036005180 - 210Left rear140025004125 - 145Right front140025004125 - 145Right...

Electric supply:230 V ~ 50 HzAppliance category:II2H3+ Gas connection:R 1/2" Appliance class:3 9.5 Gas burners for NATURAL GAS G20 20 mbarBURNERNORMAL POWER kWMINIMUM POWER
kWINJECTOR MARK
1/100 mmDual5,01,4270 / 115Dual (internal
crown)0,80,33709.6  Gas burners for LPG G30/G31 28-30/37 mbarBURNERNORMAL
POWER kWMINIMUM
POWER kWINJECTOR
MARK 1/100
mmNOMINAL GAS FLOW g/hG30 28-30
mbarG31 37 mbarDual4,61,4246 / 72334328Dual (inter-
nal crown)0,80,3346585710.  ENVIRONMENTAL CONCERNSRecycle the materials...

ENGLISH27 

www.aeg.com/shop867305016-A-112014