AEG Mixed Hob HD955100NB User Manual

							CAUTION!
Make sure that the gas
supply pressure of the
appliance obeys the
recommended values.Rigid connection:
Carry out connection by using metal rigid
pipes (copper with mechanical end).
8.5  Injectors replacement
1.Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the
injectors and replace them with the
ones which are necessary for the type of gas you use (see table in
"Technical Information" chapter).
4. Assemble the parts, follow the same
procedure backwards.
5. Replace the rating plate (it is near the
gas supply pipe) with the one for the new type of gas supply. You can find
this plate in the package supplied
with the appliance.
If the supply gas pressure is changeable
or different from the necessary pressure,
you must fit an applicable pressure
adjuster on the gas supply pipe.8.6  Adjustment of minimum
level
To adjust the minimum level of the burners:
1. Light the burner.
2. Turn the knob on the minimum
position.
3. Remove the knob.
4. With a thin screwdriver, adjust the
bypass screw position (A for external
crown and B for internal crown).
5. If you change:
• from natural gas G20 20 mbar to liquid gas, fully tighten the bypass
screw in.
• from liquid gas to natural gas G20 20 mbar, undo the bypass screw
approximately 1/4 of a turn for
internal crown (B) and
approximately 1/3 of a turn for
external crown (A).
WARNING!
Make sure the flame does
not go out when you quickly
turn the knob from the
maximum position to the
minimum position.8.7  Electrical connection
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug (if applicable).
• The appliance must not be connected with an extension cable, an adapter or
a multiple socket. There is a risk of fire.
• Do not let the power cable to heat up
to a temperature of more than 90° C.The cable should be guided by means
ENGLISH21   A B   
						

							of clamps fixed to the side of the
cabinet, in order to avoid any contact with the equipment beneath thecooktop.Electrical Requirements
Permanent electrical installation must
agree with the latest I.E.E. Regulations and local Electricity Board regulations.
For your own safety the installation must
be done by a qualified electrician (e.g.
your local Electricity Board, or a
contractor who is on the roll of the
National Inspection Council for Electrical
Installation Contracting [NICEIC]).
The manufacturer refuses
to be held responsible, if
these safety measures are
not abided by.Supply connections
This hob has to be connected to 230 — 240 V ( 50 Hz) electricity supply.
The hob has a terminal block which is
marked as follows:
• L or  1 - live terminal
• N or  4 - neutral terminal
•
 or  E or  5 - earth terminal
Before carrying out the connection,
make sure:
1. The limiter valve and the electrical
system can take the appliance load
(see the rating plate)
2. The supply system is equipped with
an efficient earth connection in
compliance with the current
standards and regulations
3. The outlet or omnipolar switch used
for connection is easily accessible
with the appliance installed.
You must purchase and install the power
cable. Use only a connection cable of type H05V2V2-F T90 or its equivalent.
Make sure that the cable section is
applicable to the voltage load and the
working temperature.
The wires in the cord are coloured as
follows:
Green and yellow- EarthBlue- NeutralBrown- LiveWARNING!
A cut off plug inserted into a
13 amp socket is a serious
shock hazard. Ensure that
the cut off plug is disposed
of safely.8.8  Replacement of the
connection cableThe replacement of electric
cable must be carried out
exclusively by the service
force centre or by personnel
with similar competencies, in
accordance with the current
regulations.Make sure that the cable
section is applicable to the
voltage load and the
working temperature. The
yellow/green earth wire (B)
must be approximately 2 cm
longer than the live and
neutral wire (A).
1. Connect the green and yellow (earth)
wire to the terminal which is marked
with the number 5, or the letter 'E', or
the earth symbol 
, or coloured
green and yellow.
2. Connect the blue (neutral) wire to the
terminal which is marked with the
number 4, or the letter 'N', or
coloured blue.
3. Connect the brown (live) wire to the
terminal which is marked with the
number 1, or the letter 'L'. It must
always be connected to the network
www.aeg.com22     A B   
						

							phase. There must be no cut or stray
strands of wire present. The cord
clamp must be correctly attached to
the outer sheath.8.9  Attaching the seal
1.Clean the worktop around the cut
out area.
2. Attach the supplied seal stripe to the
lower edge of the hob along the
outer edge of the glass ceramic. Do
not extend it. Make sure that the
ends of the seal stripe are located in the middle of one side of the hob.
3. Add some mm when you cut the seal
stripe to the length.
4. Push the two ends of seal stripe
together.8.10  AssemblyENGLISH23min. 450mm
min.650mm
min. 2mm  < 20 mm
min. 2 mm
A
B
 A 12 mm28 mm 38 mm  B 57 mm41 mm31 mm
min  30 mmmin. 500 mm > 20 mm
min. 2 mm
A
B
 A 12 mm28 mm 38 mm  B 57 mm41 mm31 mm
min. 500 mm  
						

							CAUTION!
Install the appliance only on
a worktop with a flat surface.8.11  Possibilities for insertionKitchen unit with door
The panel installed below the hob must
be easy to remove and let an easy access
in case a technical assistance
intervention is necessary.
A) Removable panel
B) Space for connections
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
www.aeg.com24R 5 mm
min. 55 mm
490  
mm830  
mm
600 mm min. 38 mm min. 2 mm min. 12 mm min.  2 mm   min. 40 mm  (+2 mm)
min. 30 mmmin. 60 mm
b a   
						

							safety reasons and to let easy remove
oven from the unit.If you install the hob
asymmetrically rightward the
minimum distance between
left edge of the hob and left
support must be 72 mm.9.  TECHNICAL INFORMATION9.1  Hob dimensionsWidth880 mmDepth520 mm9.2 Cooking zones specificationCooking zoneNominal power
(maximum heat
setting) [W]Power function
[W]Power function
maximum dura-
tion [min]Cookware diam-
eter [mm]Left front220036005180 - 210Left rear140025004125 - 145Right front140025004125 - 145Right rear1800280010145 - 180The power of the cooking zones can be different in some small range from the
data in the table. It changes with the
material and dimensions of the
cookware.For optimal cooking results use
cookware not larger than the diameter in
the table.9.3  Bypass diametersBURNERØ BYPASS 1/100 mmDual (internal crown)29Dual (external crown)579.4 Other technical data
TOTAL POWER:
Gas original:G20 (2H) 20 mbar = 5 kWGas replacement:G30 (3+) 28-30 mbar = 334 g/h
G31 (3+) 37 mbar = 329 g/hElectric zones:6,8 kWENGLISH25 min.  72 mm  
						

							Electric supply:230 V ~ 50 HzAppliance category:II2H3+ Gas connection:R 1/2" Appliance class:3 9.5 Gas burners for NATURAL GAS G20 20 mbarBURNERNORMAL POWER kWMINIMUM POWER
kWINJECTOR MARK
1/100 mmDual5,01,4270 / 115Dual (internal
crown)0,80,33709.6  Gas burners for LPG G30/G31 28-30/37 mbarBURNERNORMAL
POWER kWMINIMUM
POWER kWINJECTOR
MARK 1/100
mmNOMINAL GAS FLOW g/hG30 28-30
mbarG31 37 mbarDual4,61,4246 / 72334328Dual (inter-
nal crown)0,80,3346585710.  ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol 
 with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
*
www.aeg.com26   
						

							ENGLISH27 
						

							www.aeg.com/shop867305016-A-112014