AEG Lavamat L 16850 Manual

41What to do if...
The machine does not dry or does
not dry properly
The drying time or the dryness degree has not been
selected .
 Select the drying time or the dryness degree
The water tap is not turned on (
E10)
 Open the water tap.
The drain filter is clogged (
E20)
 Clean the drain filter.
The machine is overloaded.
 Introduce into the drum less laundry.
The selected drying programme, time or dryness
degree was not suitable for the laundry
 Select the suitable drying programme, time or
dryness...

42What to do if...
Technical Data
Dimensions
Width
Height
Depth (door included)60 cm
85 cm
63 cm
Electrical connection
Water supply pressureMinimum
Maximum0,05 MPa
0,80MPa
Maximum LoadCottons7 kg
Spin SpeedMaximum1600 rpm
Maximum Dry Load Cotton
Cotton Big Capacity
Synthetics3.5 Kg
5.0Kg
2.0kg
Power supply voltage/frequency
Total power absorbed
Minimum fuse protection220-230 V/50 Hz
2050 W
10 A
Problem Cause possible/Solution
If you are unable to identify or solve the problem,
contact our service centre....

43Consumption value
Consumption value
The consumption data shown on this chart is to be considered purely indicative, as
it may vary depending on the quantity and type of laundry, on the inlet water
temperature and on the ambient temperature.
(*) «Economy 60°C» with a load of 7 kg is the reference programme for the data
entered in the energy label, in compliance with EEC 92/75 standards.
Programme Water consumption
(lltres)Energy consumption
(KWh)Programme duration
(Minutes)
White Cottons 95°622.1
For...

44Installation
Installation
Unpacking
All transit bolts and packing must be removed before using the appliance.
You are advised to keep all transit devices so that they can be refitted if the
machine ever has to be transported again.
1.After removing all the packaging, carefully lay
machine on it’s back to remove the
polystyrene base from the bottom.
2.Remove the power supply cable and the
draining hose from the hose holders on the rear of the
appliance.
3.
With a suitable spanner unscrew and remove the...

4.Unscrew and remove the two large rear bolts B
and the six smaller bolts C.
5.Remove the bracket Dand tighten up the six
smaller bolts C. Slide out the relevant plastic
spacerE.
6.Open the porthole, take out the inlet hose from the
drum and remove the polystyrene block fitted on the
door seal.
7.Fill the smaller upper hole and the two large ones with
the corresponding plastic plug caps supplied in the bag
containing the instruction booklet.
8.Connect the water inlet hose as described under the
paragraph...

46Installation
	

	

Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not impeded by carpets,
rugs etc.
Before placing it on small tiles, apply a rubber coating.
Never try to correct any unevenness in the floor by putting pieces of wood,
cardboard or similar materials under the machine.
If it is impossible to avoid positioning the machine next to a gas cooker or coal-
burning stove, an insulating panel covered with...

requirements. A minimum water pressure of 0.05
MPa is required for safe operation of the appliance.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system. There
should be a minimum distance of between the appli-
ance’s inlet and the bottom of the water storage tank.
Water-stop device
The inlet hose is provided with a water stop device,
which protects against damage caused by water leaks in
the hose which...

When discharging into a standpipe
ensure that the top of the standpipe is
no more than 90 cm (35.4) and no less
than 60 cm (23.6) above floor level.
The drain hose may be extended to a
maximum of 4 metres. An additional
drain hose and joining piece is available
from your local Service Force Centre.
The joining piece must have an internal
diameter of 18 mm.
If your drain hose looks like this (see the relevant
pcture) you do not require the “U” piece”. Just push
the hose firmly into the standpipe.
2. Onto...

49Installation
In the interest of the environment
Washing machines and dishwashers
should be connected to the FOUL
drainage system, the water will then
be taken to a sewage works for
treatment before being discharged
safely into a river.
It is essential that these appliances
are not connected to the surface
water drainage system as this water
is discharged directly into a river or
stream and may cause pollution.
If you require any further advice
please contact your local water
authority.
Electrical...

50Installation
If you fit your own plug, the colours of the wires in the mains lead of your appli-
ance may not correspond with the markings identifying the terminals in your plug,
proceed as follows:
Connect the green and yellow (earth) wire to the terminal in the plug which is
marked with the letter «E» or the earth symbol  or coloured green and yellow.
Connect the blue (neutral) wire to the terminal in the plug which is marked with
the letter «N» or coloured black.
Connect the brown (live) wire to the...