AEG Lavamat 47080 Information Manual
Have a look at the manual AEG Lavamat 47080 Information Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 513 AEG manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User information22Care and cleaning Do not do any cleaning operation until you have unplugged the washing machine. Descaling the washing machine Normally there is no need to descale the washing machine if the detergent was correctly proportioned. If descaling is necessary, use a special non-corrosive product specially designed for washing machines that you can find in the shops. Respect the proportion and frequency of descaling shown on your packaging. The surface Clean the surface of your washing machine using lukewarm water and a mild detergent. Never use alcohol, solvents or similar products. The detergents dispenser From time to time, you must clean the detergents dispenser in order to eliminate the possible wastes of the detergents and then to avoid an operating problem. The detergent dispenser is very easy to remove for a light cleaning. Disassembly: Press the clips on each side of the detergents dispenser and pull it upwards.
User information 23You can thus clean it using running water and a brush or a twisted cloth. Check that the siphons at the back of the detergents dispenser are not blocked. Reassembly : Put the detergents dispenser in the notches until they lock. The drain filter Clean the filter at the bottom of the washing machine regularly. The filter* light comes on if the filter is blocked. In this case clean it immediately. If you wash washing that is very fluffy, clean it after each wash. Open the door, with a screwdriver for example:*depending on model
User information24Drain residual water: Put a receptacle under the drain. Turn the cap in the anti-clockwise direction until it is vertical to release residual water. Remove the filter: Unscrew the cap all the way and take it off. Clean it tho-roughly with running water. Put the assembly back and screw it in the clockwise direction. After cleaning the filter, you are required to closed the door. In fact, for reasons of safety, the door must be closed when the appliance is working.
User’s instructions 25Operating problems Many checks have been carried out during the manufacture of your washing machine. However, if you face a problem with its operation, please read the following sections before calling the After Sales ser- vice. SymptomCauseThe washing machine will not start or will not fill•the washing machine is not correctly connected, the electrical installation is not working, •the cover of your washing machine and the drum flaps are not correctly closed, •you did not control the program start correctly, •there is a power failure, •the water supply is closed off, •the water tap is closed, •the water inlet is blocked.The washing machine fills up but empties again im- mediately•the drain siphon is attached too low (see installation section).The washing machine will not spin or will not empty•the drain pipe is blocked or kinked, •the drain filter is blocked, •the anti-unbalance mass safety device has tripped; bad distribution of washing in the drum,•the «Drain» program or the «Rinse hold» option is selected,•the height of the drain siphon is wrong.
User’s instructions26There is water on the floor around the washing ma- chine•excess detergent has made too much foam that overflowed, •the detergent is not suitable for washing machine, •the drain siphon is not hooked on pro- perly, •the drain filter was not put back into place, •the water inlet pipe is leaking.Washing results are not sa- tisfactory•the detergent is not suitable for machine washing, •there is too much washing in the drum, •the washing program is not appro- priate, •there is not enough detergent.The machine is vibrating or noisy•not all the packing was removed from the machine (see unpacking section), •the washing machine is not leveled and properly packed, •the washing machine is too close to the wall or furniture, •the washing is not well distributed in the drum, •the load is not sufficient.The cover does not open during the cycle•the «DOOR»* light is off, •the temperature of the washing water is too high. •the cover cannot open until 1 to 2 minutes after the washing machine has stopped*.The washing machine stops during a washing cycle•the water or electricity supply is defective, •a rinse hold was programmed.SymptomCause
User’s instructions 27The washing cycle is much too long•the water inlet is blocked, •there was a power supply failure or the water was cut off, •the motor temperature safety device tripped, •the water inlet temperature is lower than normal, •the foam detection safety system trip- ped (too much detergent) and the washing machine evacuated the foam, •the anti-unbalance mass safety device tripped, an additional phase was added to distribute the washing in the drum better.The «End» light** flashes 4 times and the error code E40 appears in the display window•the cover is not correctly closed.The «End» light** flashes 2 times and the error code E20 appears in the display window•the drain filter is blocked, •the drain pipe is blocked or kinked, •the drain pipe is too high (see «instal- lation»), •the drain pump is blocked, •the installation siphon is blocked.The «End» light** flashes 1 time and the error code E10 appears in the display window•the water tap is closed, •the water network has been cut off.The «End» light** flashes 10 times and the error code EA0 appears in the display window•the flaps of the drum door are opened.SymptomCause
User’s instructions28Softener or Javel water flows through the over- flow orifice when filling* •you did not put in the right amount, •the siphons at the back of the deter- gents dispenser are blocked. *depending on model. ** Eliminate the causes of the failure if you find them, and then press on the «Start/Pause» pusbutton to restart the interrupted program.SymptomCause
User information 29A. FOR THE INSTALLER Installation and connection instructions Warnings •This washing machine is heavy. Take care when moving it. •You must remove the packing on the washing machine before use. Failure to remove all transport protection devices can cause damage to the washing machine or nearby furniture. The washing machine must be unplugged while packing is being removed. •Do not allow any one other than a qualified plumber to make the hydraulic connections necessary to install your washing machine. •The washing machine must be plugged in to a power outlet with a conform earth. •Call a qualified electrician if the electrical installation in your residence is such that you have to modify it before you can con- nect your washing machine. •Please read the instructions in the electrical connections chap- ter carefully before connecting your washing machine. •After installing your washing machine, make sure that it is not standing on its electrical power supply cable. •When your machine is installed on a carpeted floor, make sure that the carpet does not close off the ventilation openings near the bottom of the machine. •The power supply cable may be only replaced by the After Sales Service. •Your manufacturer cannot be held responsible for any damage resulting from a nonconform installation.
User information30Unpacking Packing used to protect internal parts of the washing machine during transport must be removed before the washing machine is put into service for the first time. Remove all packing from the washing machine. Tilt the washing machine sideways and then remove the packing under the motor, and straighten the washing machine. Tilt the washing machine back-wards, rotate it by a quarter of a turn on one of its corner to remove the transport base. Open the washing machine lid and remove the immobilization packing and plastic films. Close the lid. Use a 10 mm spanner to remove the two screws and spacers at the back.