AEG Lavamat 14710 Vit Instruction Booklet

51
Set the machine
upright and remove
the two remaining
bolts from the back.
Pull out the three
plastic spacers from
the holes into which
the bolts were fit-
ted.
Plug the open holes with the plugs which you will find in the plastic ba\
g
containing the instruction booklet.
You are advised to keep all transit devices so that they can be refitted if the machine
ever has to be transported again.
Positioning
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not...

Water inlet (cold water connection only)
Connect the hose to a
tap with a 3/4” thread.
Installation should
comply with local
water authority and
building regulations’
requirements.
Set the hose correctly
by loosening the ring
nut. After positioning the inlet hose, be sure to tighten the ring nut again to
prevent leaks.
Do not connect to a hot water supply.
The inlet hose is provided with a water stop device,
which protects against damage caused by water
leaks in the hose which could develop due to nat-...

When discharging into a stand-
pipe ensure that the top of the
standpipe is no more than 90
cm (35.4) and no less than 60
cm (23.6) above floor level.
The drain hose may be extend-
ed to a maximum of 4 metres.
An additional drain hose and
joining piece is available from
your local Service Force Centre. The joining piece must have an internal
diameter of 18 mm.
2. Onto a sink outlet spigot.
If the outlet spigot
has not been used
before, remove any
blanking plug that
may be in place.
Push the drain hose...

In the interest of the environment
Washing machines and dish-
washers should be connected
to the FOUL drainage system,
the water will then be taken
to a sewage works for treat-
ment before being discharged
safely into a river.
It is essential that these appli-
ances are not connected to the
surface water drainage system
as this water is discharged
directly into a river or stream
and may cause pollution.
If you require any further
advice please contact your local
water authority.
Electrical connections...

55
If you fit your own plug, the colours of the wires in the mains lead of your
appliance may not correspond with the markings identifying the terminals in
your plug, proceed as follows:
Connect the green and yellow (earth) wire to the terminal in the plug which
is marked with the letter «E» or the earth symbol  or coloured green and
yellow.
Connect the blue (neutral) wire to the terminal in the plug which is marked
with the letter «N» or coloured black.
Connect the brown (live) wire to the terminal in...

Building-in
This appliance has been designed to
be built into the kitchen furniture.
The recess should have the dimen-
sions shown in picture A.
When installing the appli-
ance into the kitchen furni-
ture ensure, if possible, the
hoses are placed in either of
the two recesses on the back
of the appliance. This will
help to prevent the hoses
from becoming kinked or
trapped. Picture AB.
Preparation and assembly of the door
The machine is originally pre-
arranged for the assembly of a door
opening from...

b) Hinges
To mount the hinges it is necessary to
drill two holes (dia. 35 mm, depth
12.5-14 mm) on the inner side of the
door. The distance between the holes
hobs fixing centres must be 416 mm.
The distance (B) from upper edge of
the door to the centre of the hole
depends on the adjacent furnitures
dimensions.
The required dimensions are given in the picture C.
The hinges will be fixed to the door by means of screws for wood (2-Fig. B) sup-
plied with the appliance.
c) Mounting the door
Fix the hinges...

Recommendations regarding the construction and fitting of
a base when the installation requires an integrated appliance
to be raised
Where the appliance has been raised by mounting onto a wooden base pro-
vided by the installer. The material used to construct the base should have a
non slip surface, be water repellent and if possible be one solid piece.
If it is not possible to
use one solid piece, due
to the additional height
required, ensure that
any additional strips of
timber are glued and
screwed...

With the appliance installed adjust all four feet ensuring the machine i\
s
stable, and a clearance of approximately 5 mm is left between the top of
the machine and the underside of the worktop.
A final check for stability should be carried out with the machine on sp\
in with
a load, this will identify the need for any further fine adjustment to t\
he feet.
A strip of beading approximately 605 mm W, x 5 mm H, x 25 mm D must be
screwed down into the base directly in front of the machine’s feet, this...

AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG
132.984.531-01-0805      Subject to change without notice.
From the Electrolux Group.The world’s No. 1 choice.
The Electrolux Group is the worlds largest producer of powered appliances for kitchen, cleaning and
outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing
machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of 
approx....