AEG Induction hob HKP87420FB User Manual

display switches between  and
counted time (minutes).
To see how long the cooking zone operates:  set the cooking zone with 
.
The indicator of the cooking zone starts to flash quickly. The display shows how
long the zone operates.
To deactivate the function:  set the
cooking zone with 
 and touch  or
. The indicator of the cooking zone
goes out.
Minute Minder
You can use this function as a  Minute
Minder  when the hob is activated and
the cooking zones do not operate. The
heat setting display shows 
....

4.12 Power management
function
• Cooking zones are grouped according to the location and number
of the phases in the hob. See the illustration.
• Each phase has a maximum electricity loading of 3700 W.
• The function divides the power between cooking zones connected to
the same phase.
• The function activates when the total electricity loading of the cooking
zones connected to a single phase exceeds 3700 W.
• The function decreases the power to the other cooking zones connected to
the same phase.• The...

Place the cookware with the bottom
diameter larger then 160 mm centrally
between two sections.
5.2  FlexiBridge Standard
mode
This mode is active when you activate
the hob. It connects the sections into two
separate cooking zones. The sides of the zones which operate together in this
mode light up, and they are linked with
shorter illuminated lines. You can set the
heat setting for each zone separately. Use two left side control bars.
Correct cookware position:
Incorrect cookware position:
5.3...

Incorrect cookware position:
5.4 FlexiBridge Max Bridge
mode
To activate the mode press  until you
see the correct mode indicator 
. This
mode connects all sections into one
cooking zone. To set the heat setting use
any of the two control bars on the left
side.
Correct cookware position:
To use this mode you have to place the cookware on the four connected
sections. If you use cookware smaller
than three sections the display shows 
and after 2 minutes the zone switches off.
Incorrect cookware position:...

General information:
• 160 mm is the minimum bottom diameter of the cookware for thisfunction.
• Heat setting display for the left rear control bar shows the position of the
cookware on the induction cooking
area. Front 
, middle , rear
.
• Heat setting display for the left front control bar shows the heat setting.  To
change the heat setting use left front control bar.
• When you activate the function for the
first time you will get heat setting 
for the front position,  for the
middle position and...

The printing on the flexible
induction cooking area may
become dirty or change
colour from sliding the
cookware. You can clean the
area in a standard way.The bottom of the cookware
must be as thick and flat as
possible.
Cookware dimensions
Induction cooking zones adapt to the dimension of the bottom of the
cookware automatically to some limit.
The cooking zone efficiency is related to
the diameter of the cookware. The
cookware with a smaller diameter than
the minimum receives only a part of the power...

Heat settingUse to:Time
(min)Hints7 - 9Steam potatoes.20 - 60Use max. ¼ l water for 750 g of
potatoes.7 - 9Cook larger quantities of food,
stews and soups.60 - 150Up to 3 l liquid plus ingredi-
ents.9 - 12Gentle fry: escalope, veal cor-
don bleu, cutlets, rissoles,
sausages, liver, roux, eggs,
pancakes, doughnuts.as nec-
essaryTurn halfway through.12 - 13Heavy fry, hash browns, loin
steaks, steaks.5 - 15Turn halfway through.14Boil water, cook pasta, sear meat (goulash, pot roast), deep-fry chips.Boil...

8.1 What to do if...ProblemPossible causeRemedyYou cannot activate or oper-
ate the hob.The hob is not connected to
an electrical supply or it is
connected incorrectly.Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram. The fuse is blown.Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.  Activate the hob again and
set the heat setting in less
than 10 seconds. You touched 2 or...

ProblemPossible causeRemedyThere is no signal when you
touch the panel sensor
fields.The signals are deactivated.Activate the signals.
Refer to "Daily use" chapter.The flexible induction cook-
ing area does not heat up
the cookware.The cookware is in the
wrong position on the flexi-
ble induction cooking area.Place the cookware in the
correct position on the flexi-
ble induction cooking area.
The position of the cook-
ware depends on the activa-
ted function or function
mode.
Refer to...

ProblemPossible causeRemedy PowerSlide function oper-
ates. Two pots are placed on
the flexible induction cook-
ing area.Use only one pot.
Refer to "Flexible induction
cooking area" chapter. and a number come on.There is an error in the hob.Disconnect the hob from the
electrical supply for some
time. Disconnect the fuse
from the electrical system of
the house. Connect it again.
If 
 comes on again, speak
to an Authorised Service
Centre.
 comes on.The electrical connection is
incorrect. The supply...