AEG Induction hob HC452601EB User Manual

4.7 OffSound Control
(Deactivating and activating
the sounds)
Deactivate the hob. Touch 
 for 3
seconds. The display comes on and goes
out. Touch 
 for 3 seconds.  or 
comes on. Touch  of the timer to
choose one of the following:
•
 - the sounds are off
• - the sounds are on
To confirm your selection wait until the hob deactivates automatically.
When the function is set to 
 you can
hear the sounds only when:
• you touch 
• Minute Minder comes down
• Count Down Timer comes down
• you put something on the...

Always preheat the hob.Food to be cookedTemperature (°C)Time / TipsFish and shellfish140 – 160Preheat the hob.Salmon fillets1608 minutes, turn after 4 mi-
nutes.King prawns (without shell)1406 minutes, turn after 3 mi-
nutes.Shark steaks, approximately
2.5 cm thick16010 minutes, turn after 5 mi-
nutes.Sole, Müllerin Art (fried in
butter)1408 minutes, turn after 4 mi-
nutes, light side first.Plaice filets1406 minutes, turn after 3 mi-
nutes.Veal140 – 180Preheat the hob.Veal chop18010 minutes, turn after 5...

Food to be cookedTemperature (°C)Time / TipsHamburger1606 - 8 minutes, turn after 3 - 4
minutes.Châteaubriand160 then 100Sauté the meat in oil on all
sides (turn only when the
meat does not stick to the
pan). Finish off on one side
for 10 minutes (100 °C).Pork160 – 180Preheat the hob.Pork medallions1608 minutes, turn after 4 mi-
nutes (depending on the
thickness).Pork steaks1808 minutes, turn after 4 mi-
nutes.Pork escalopes1606 minutes, turn after 3 mi-
nutes.Spare ribs1608 - 10 minutes, turn several...

Food to be cookedTemperature (°C)Time / TipsVegetables140 - 16010 - 20 minutes, turn several
times.Vegetables140 - 16010 - 15 minutes, under a
cooking lid (turn halfway
through).Cooking precooked rice140 - 16010 - 15 minutes, turn several
times.Cooking precooked noodles140 - 16015 - 20 minutes, turn halfway
through.6.  CARE AND CLEANINGWARNING!
Refer to Safety chapters.6.1  General information
Clean the hob after each use.
Always use cookware with clean bottom.
WARNING!
Sharp objects and abrasive...

7.1 What to do if...ProblemPossible causeRemedyYou cannot activate or oper-
ate the hob.The hob is not connected to
an electrical supply or it is
connected incorrectly.Check if the hob is correctly
connected to the electrical
supply. Refer to the connec-
tion diagram. The fuse is blown.Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a quali-
fied electrician.  Activate the hob again and
set the heat setting in less
than 10 seconds. You touched 2 or...

ProblemPossible causeRemedy and a number come on.There is an error in the hob.Disconnect the hob from the
electrical supply for some
time. Disconnect the fuse
from the electrical system of
the house. Connect it again.
If 
 comes on again, speak
to an Authorised Service
Centre.
 comes on.The electrical connection is
incorrect. The supply voltage
is out of range.Speak to a qualified electri-
cian to check the installation. comes on.There is an error in the hob
because a cookware boiled
dry. Automatic...

8.2 Built-in hobs
Only use the built-in hobs after you
assemble the hob into correct built-in units and work surfaces that align to thestandards.8.3  Connection cable
• The hob is supplied with a connection
cable.
• To replace the damaged mains cable use the following (or higher) mains
cable type: H05V2V2-F T min 90°C. Speak to your local Service Centre.
8.4  Attaching the seal
1. Clean the worktop around the cut
out area.
2. Attach the supplied seal stripe to the
lower edge of the hob along the
outer...

 
• Seal the gap between the worktopand glass ceramic with silicone.
• Put some soapy water on the silicone.
• Pull off the excess silicone with the scraper.8.6  Installation of more than
one hob
Supplied accessories:  connection bar,
heat-resistant silicone, rubber shape, sealing stripe.
Use only a special heat-
resistant silicone.The worktop cutoutDistance
from the
wallminimum 50 mmDepth490 mmWidthsum of all widths of hobs that
you install minus 20 mmExample:Assembly
1. Calculate correct cutout...

7.Loosely screw in the fixing plates
from below to the worktop and to
the connection bar.
8. Insert next hob into the worktop
cutout. Make sure that the front
edges of the hobs are on the same
level.
9. Tighten the fixing plates / retaining
grip screws.
10. Use silicone to seal the gaps
between the hobs and between the
hobs and the worktop.
11. Put some soapy water on the
silicone.
12. Press the rubber shape with some
strength against the glass ceramic
and move it slowly along the space.
13. Do not touch...

10. ENVIRONMENTAL CONCERNSRecycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to recycle waste of electrical and electronic
appliances. Do not dispose appliancesmarked with the symbol  with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.www.aeg.com20