AEG Front loader washing machine L76475FL User Manual

To clean the drain pump:
1.Open the drain pump door.
2.Pull the flap out to remove it.
3.Put a container below the recess of
the drain pump to collect the water
that flows out.
4.Press the two levers and pull for-
ward the drainage duct to let the
water flow out.
1
25.When the container is full of water,
put the drainage duct back again
and empty the container. Do steps 4
and 5 again and again until no more
water flows out from the drain
pump.
6.Pull back the drainage duct and turn
the filter to remove...

12
9.Clean the filter under the water tap
and put it back in the pump into the
special guides.
10.Make sure that you tighten correctly
the filter to prevent leakages.
11.Put the flap back and close the drain
pump door.
11.8 The inlet hose filter and
the valve filter
It could be necessary to clean the filters
when:
• The appliance does not fill with water.
• The appliance fills with the water for a
long time.•
The indicator of button 
4 flashes and
the display shows the related alarm.
Refer to...

Put the drainage duct back and close the
drain pump flap.
When you drain the water with the emer-
gency drain procedure, you must acti-
vate again the drain system:
1.Put 2 litres of water in the main wash
compartment of the detergent dis-
penser.
2.Start the programme to drain the
water.
11.10 Frost precautions
If the appliance is installed in an area
where the temperature can be less than
0 °C, remove the remaining water from
the inlet hose and the drain pump.
1.Disconnect the mains plug from the
mains...

ProblemPossible causePossible solution
The appliance
does not drain the
water.The water drain hose is
damaged.Make sure that the water drain
hose has no damages.
 The filter of the drain
pump is blocked.Clean the filter of the drain
pump. Refer to 'Care and clean-
ing'.
 The connection of the
water drain hose is not
correct.Make sure that the connection
is correct.
 A washing programme
without the drain phase
is set.Set the drain programme.
 The function Rinse &
Hold is on.Set the drain...

ProblemPossible causePossible solution
 Leakages from the drain
pump.Make sure that the drain pump
filter is tight.
 The water drain hose is
damaged.Make sure that the water inlet
hose has no damages.
You cannot open
the appliance
door.The washing pro-
gramme is in operation.Let the washing programme
end.
 There is water in the
drum.Set the drain or the spin pro-
gramme.
The appliance
makes an unusual
noise.Incorrect level of the ap-
pliance.Adjust the level of the appli-
ance. Refer to...

13.2 Unpacking
1.Use the gloves. Remove the external
film. If necessary, use a cutter.
2.Remove the cardboard top.
3.Remove the polystyrene packaging
materials.
4.Remove the internal film.
5.Open the door and remove all the
items from the drum.
26www.aeg.com 

6.Put one of the polystyrene packag-
ing elements on the floor behind
the appliance. Carefully put down
the appliance with the rear side on
it. Make sure not to damage the ho-
ses.
1
2
7.Remove the polystyrene protection
from the bottom.
8.Pull up the appliance in vertical po-
sition.
9.Remove the power supply cable and
the drain hose from the hose hold-
ers.
10.Remove the three bolts. Use the key
supplied with the appliance.
11.Pull out the plastic spacers.
ENGLISH27 

12.Put the plastic caps in the holes.
You can find these caps in the user
manual bag.
– We recommend that you keep
the packaging and the transit
bolts for when you move the
appliance.
– If the appliance is delivered in
the winter months when there
are minus temperatures. Store
it at room temperature for 24
hours before using for the first
time.
13.3 Positioning and levelling
x4
• Install the appliance on a flat hard
floor.
• Make sure that carpets do not stop
the air circulation below the appliance.
•...

CAUTION!
Do not put cardboard, wood or
equivalent materials below the
appliance feet to adjust the level.
Make sure that there is sufficient
access after the installation for
possible repairs by a qualified
person.
Installation on suspended
flooring
Suspended wooden floors are particular-
ly susceptible to vibration. To help pre-
vent vibration we recommend you place
a waterproof wood panel, at least 15 mm
thick under the appliance, secured to at
least 2 floor beams with screws, the
wood panel must...

Make sure not to have more than a dis-
tance of 5.02 m (16.5 ft) between the ap-pliance inlet hose and the bottom of the
water storage tank.
Water-stop device
A
The inlet hose has a water stop device.
This device prevents water leaks in the
hose because of its natural ageing. The
red sector in the window «A» shows this
fault .
If this occur, close the water tap and
contact the service centre to replace the
hose.
13.5 Water drainage
There are different procedures to con-
nect the drain hose:
With the...