AEG Front loader washing machine L76475FL User Manual

L 76475 FLEN User manual 

CONTENTS
1.SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
2.SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
3.TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
4.PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

1. SAFETY INFORMATION
Before the installation and use of the appliance, careful-
ly read the supplied instructions. The manufacturer is
not responsible if an incorrect installation and use cau-
ses injuries and damages. Always keep the instructions
with the appliance for future reference.
1.1 Children and vulnerable people safety
WARNING!
Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or...

• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly quali-
fied persons in order to avoid a hazard.
• The operating water pressure (minimum and maxi-
mum) must be between 0,5 bar (0,05 MPa) and 8 bar
(0,8 MPa)
• The ventilation openings in the base (if applicable)
must not be obstructed by a carpet.
• The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets must
not be reused.
2.  SAFETY INSTRUCTIONS
2.1...

mains plug, use a 13 amp ASTA (BS
1362) fuse.
•
This appliance complies with the
E.E.C. Directives.
Water connection
• Make sure not to cause damage to the
water hoses.
• The appliance is to be connected to
the water mains using the new sup-
plied hose-sets. Old hose sets must
not be reused.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
2.2 Use
WARNING!...

Level of protection against ingress of solid particles
and moisture ensured by the protective cover, ex-
cept where the low voltage equipment has no pro-
tection against moistureIPX4
Water supply pressureMinimum0,5 bar (0,05 MPa)
Maximum8 bar (0,8 MPa)
Water supply 1) Cold water
Maximum loadCotton7 kg
Spin speedMaximum1400 rpm
1) 
Connect the water inlet hose to a water tap with a 3/4'' thread.
4. PRODUCT DESCRIPTION
12389
5
6
7
4
10
11
12
1Worktop
2Detergent dispenser
3Control panel
4Door...

4.1 Accessories
12
34
1Spanner
To remove the transit bolts.
2Plastic caps
To close the holes on the rear side
of the cabinet after the removal of
the transit bolts.
3Anti-flood inlet hose
To prevent possible leakage
4Plastic hose guide
To connect the drain hose on the
edge of a sink.
5. CONTROL PANEL
Cottons
+ Prewash
Extr
a Sile
nt
S
ynthetics
+ Prewash
Eas
y Iro
n
Delicat
es
Wool/Silk
g k
  3
  -   . n i M
  0 2
e
v i s n e
t n I   k c
i u
Q
s n
a e
J
s n i
a
t r u Co c
E   r
e p u S
Rinse
n
i a r D
/...

• After 5 minutes from the end of the
washing programme. Refer to 'At the
end of programme'.5.2 Programme knob 2
Turn this knob to set a programme. The
related programme indicator comes on.
5.3 Display 3
ABCD
The display shows:
A• The maximum temperature of the programme.
B• The default spin speed of the programme.
•
'No Spin'
1) and 'Rinse Hold' symbols.
C•
The display symbols.2)
SymbolsDescription
Washing phase
Rinse phases
Spin phase
Child lock
You cannot open the appliance...

D• The programme time
When the programme starts, the time decreases with steps of 1 mi-
nute.
• The delay start
When you press the delay start button, the display shows the delay
start time.
• Alarm codes
If the appliance has a malfunction, the display shows alarm codes. Re-
fer to 'Troubleshooting' chapter.
•Err
The display shows this message for some seconds if:
– You set a function that is not applicable for the programme.
– You change the programme while it operates.
The indicator of the...

Spin phase is off.
'Rinse Hold' function is
on.
5.10 Temperature button 10
Press button 10 to change the default
temperature.
- -= cold water
5.11 Acoustic signals function
You can hear the acoustic signals when:
• You activate the appliance.
• You deactivate the appliance.
• You press the buttons.
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic sig-
nals, press button 
8 and button 7 at
the same time for 6 seconds.
If you deactivate the...