Advidia Network Camera A 55 Quick Start Guide

 A-55·Quick Start Guide 
 10 
10 
 
Figure 1-3 Wiring (B) 
Table 1-3 Description (B) 
No. Description 
1 AUDIO IN, G: Audio input interface 
2 AUDIO OUT, G: Audio output interface 
3 IN, G: Alarm input interface 
1A, 1B: Alarm output interface 
4 D+, D-: RS-485 interface 
5 Power supply interface 
6 10M/100M self-adaptive Ethernet interface 2
1
3
4
5
6
AUDIO OUT
AUDIO IN
DC12V+-
RS485D-D+  

 A-55·Quick Start Guide 
 11 
11 
2 Installation 
Before you start: 
 Make sure the device is in good condition and all the assembly parts are included. 
 Make sure all the related equipment is power-off during the installation. 
 Check the specifications of the products to ensure they match the 
installation environment. 
 Make sure the power supply matches the required voltage to avoid damage. 
 If the product does not function properly, please contact your dealer or the nearest service center. Do...

 A-55·Quick Start Guide 
 12 
12 ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into 
the lens causing reflection.  
● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring 
and the dome cover are attached seamlessly.  
Steps: 
1. Drill four screw holes in the wall according to the No.2 holes of...

 A-55·Quick Start Guide 
 13 
13 
 
Figure 2-2 Install the Junction Box 
4. Route the cables of the camera. 
 Route the cables through the junction box and the cable hole if 
there is a cable hole drilled on the ceiling. 
 Route the cables through the side outlet of the junction box to the surface of the ceiling if there is no cable hole drilled on the ceiling. 
5. Hook the camera to the junction box with the safety cable. 
Junction Box   

 A-55·Quick Start Guide 
 14 
14 6. Tighten the screws to fix the camera to the junction box. 
 
Figure 2-3 Fix the Camera to the Junction Box 
7. Loosen the screws on the bracket to adjust the camera to the desired angle and then tighten the screws to secure the camera.   

 A-55·Quick Start Guide 
 15 
15 
 
Figure 2-4 Adjust Monitoring Angle 
Note: 
Please loosen the screws slightly until you can adjust the camera without removing the screws from the bracket. 
8. This product has an electronic lens, so adjust the camera to the 
proper surveillance angle via 3-axis adjustment, then adjust the zoom and focus by logging into the web interface of the device, and adjusting it from the PTZ control interface found on the top 
header of the Live View Image Tilt Adjust Nut
Pan...

 A-55·Quick Start Guide 
 16 
16 
 
Figure 2-5 Zoom and Focus Adjustment 
9. Tighten all screws and adjust the sun shield to the desired 
position to finish the installation. 
  

 A-55·Quick Start Guide 
 17 
17 
3 Setting the Network Camera over the 
LAN 
Purpose: 
To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet with your PC. Then, install the SADP or PCNVR software to search and change 
the IP of network camera. 
 The following figure shows the cable connection of network camera and PC: 
 
Figure 3-1 Wiring over LAN 
 Set the IP address of the camera for accessing via LAN. 
Steps: To set the IP address,...

 A-55·Quick Start Guide 
 18 
18  To view and configure the camera via LAN (Local Area Network), you need to connect the network camera in the same subnet 
with your PC. Then, install the Advidia Camera Finder Utility.  
Refer to the following introductions to set IP address with the Advidia Camera Finder Utility software (for more detailed instructions please download the Camera Finder manual from 
the Advidia Website www.advidia.com/support): 
 After launching the Advidia Camera Finder software, it...

 A-55·Quick Start Guide 
 19 
19 Note: 
To perform a manual search for additional cameras: 
Click the refresh icon  to refresh the online device list 
manually. The newly discovered devices will be added to the 
list. 
Note: 
You can click on each column heading to order the 
information. 
 Modify device information 
Steps: 
1). Select the device(s) to be modified in the device list as 
shown in Figure 3-3.  
2). Click on “File” and select “Login Manager ” as shown in Figure 3-4 to enter the username...