Advidia A64 Dome Camera Quick Start Guide

							Network Dome Camera · Quick Start Guide  102 Installation Before you start:  Make sure the device in the package is in good condition and all the assembly parts are included.  Make sure all the related equipment is power-off during the installation.  Check the specification of the products for the installation environment.  Make sure the power supply is matched with your required voltage to avoid damage.  If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself.  Make sure that the wall is strong enough to withstand three times the weight of the camera.  For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection:  ● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished. If there is dust or grease on the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol. ● Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.   
						

							Network Dome Camera · Quick Start Guide  11● The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly.  2.1 Ceiling Mounting Steps:  1. Drill the screw holes and the cable hole in the ceiling according to the supplied drill template. Drilling TemplateScrew h ole 1:for Mounting BaseHole A:for cables routed through the ceilingFRONTA1Cable Outlet11 Figure 2-1 Drill Template 2. Hammer the supplied screws to the ceiling.  Do not install the screws into the ceiling completely. It is recommended you install only enough of a screw into the ceiling, so as to hook the camera to the screws.  
						

							Network Dome Camera · Quick Start Guide  12  Figure 2-2 Installation of the Screws 3. Use a hexagonal screwdriver to loosen the lock screw on the bubble, and remove the black liner. 4. Route the cables from the cable hole, and connect the corresponding cables.  You can select to route the cables from the side outlet instead of the cable hole in the ceiling. See Figure below.  
						

							Network Dome Camera · Quick Start Guide  13Side Outlet Figure 2-3 Route the Cables via Side Outlet 5. Align the screws holes on the camera to the inserted screw, and rotate the camera to hook the camera to the screws. 6. Tighten the screws. 7. Install the black liner and bubble back.  
						

							Network Dome Camera · Quick Start Guide  14 Figure 2-4 Install the Black Liner and Bubble 8. Tighten the lock screw on the bubble.  Figure 2-5 Tighten the Lock Screw  
						

							Network Dome Camera · Quick Start Guide  152.2 Wall Mounting  You need to purchase a wall bracket separately if wall mounting is selected. 1. Fix the wall bracket to the wall with the screws. Please insert the expansion screws first if the camera is mounted to the cement wall, and you can use the self-tapping screws directly if camera is mounted to the wooden wall. 2. Install the bowl-shape cover to the wall bracket.  Figure 2-6 Install the Wall Bracket 3. Align the supplied rubber ring to the bowl-shape cover. 4. Insert the screws half-deep to the screws holes on the rubber ring.  
						

							Network Dome Camera · Quick Start Guide  16Screw Figure 2-7 Install the Rubber Ring and Screws 5. Align the screws holes on the camera to the installed screws, and rotate the camera to hook to the camera to the screws. 6. Install the black liner and bubble.  Figure 2-8 Install the Black Liner and Bubble  
						

							Network Dome Camera · Quick Start Guide  177. Tighten the lock screw on the bubble. Lock Screw Figure 2-9 Tighten the Lock Screw 2.3 3-axis Adjustment and Lens Adjustment 2.3.1 3-axis Adjustment This series of camera supports 3-axis adjustment, and you can adjust the camera to the desired surveillance angle after the black liner is installed.   
						

							Network Dome Camera · Quick Start Guide  180°~80°0°~355°0°~355° Figure 2-10 3-axis Adjustment 2.3.2 Lens Adjustment Please refer to the chapter 3 and chapter 4 for details to login to the camera.  Figure 2-11 Zoom/Focus Adjustment Via Live View  Connect the camera to a debug monitor so as to get the live view, and adjust the zoom lever (T~W) to adjust the zoom, and adjust the focus lever (F~N) to adjust the focus till you get a clear view.  
						

							Network Dome Camera · Quick Start Guide  1921 Figure 2-12 Lens Adjustment