Home > Advance Lifts > Lift > Advance Lifts Dock Lifts Pit Mounted Manual

Advance Lifts Dock Lifts Pit Mounted Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Advance Lifts Dock Lifts Pit Mounted Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 3 Advance Lifts manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
     
     
    SECTION 13: OPTION INFORMATION 
     
    Limit Switches: 
      2000, 3000 & 4000 Series: Limit switches are mounted to the base frame and 
    activate off a factory welded bracket on the scissors legs. To adjust: Raise unit to 
    desired height, loosen the arm set screw and rotate limit switch activator arm until it 
    comes into contact with the activation plate. Cycle the lift to check for correct height. If 
    too high, lower the lift an equal distance of the over-travel and reset limit switch. If too 
    low, raise the lift an equal distance above desired height and reset the switch. Repeat 
    this process until desired height is achieved.  
     
      T-Series: Limit switches are mounted to a U-channel along the side of the base 
    frame. The contact arm is activated by the wheel clevis straps welded to the side of the 
    scissors leg. The limit switch contact arm cannot be set above a parallel plane of the 
    base frame. Depending on the levelness of the installation, it may be necessary to bend 
    the contact arm slightly to make consistent contact with the clevis straps. To adjust the 
    limit switch, raise the unit to desired height. Preset the contact arm facing the clevis 
    straps on a downward angle and tighten the set screw. Slide the whole limit switch 
    assembly toward the clevis and listen for the limit switch to activate. Tighten set screws 
    and operate the lift to check for desired height. Make slight forward and back 
    adjustments to fine tune the set point.   
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
      
    						
    							 
     
    SERIES 2000 PARTS LIST 
     
    GENERAL DESCRIPTION PART # GENERAL DESCRIPTION PART #
    MECHANICAL: COMPLETE POWER UNIT:
    WHEEL ASSEMBL
    YP-005-244 23O VOLT, 1 PH, 24VA, WITH PUSHBUTTON P-004-896
    WHEEL BASE & PLATFORM PIN (1-1/4 x 3-3/4) P-A-0216 230 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-003-562
    WHEEL, BASE AND PLATFORM PIN SNAP RING P-001-061 460 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-004-895
    MAIN AXLE PIN (1-3/4 x 6-7/8) P-A-0227
    MAIN AXLE PIN SNAP RING 1-3/4 P-001-063CONTROL BOX. COMPLETE:
    UPPER WHEEL PIN ASM (TATTLE-TALE) P-015-484 230 VOLT, 1 PHASE P-004-790
    UPPER WHEEL PIN PLUG (TATTLE-TALE) P-A-4258 230 VOLT, 3 PHASE P-003-966
    STEEL HANDRAIL WITH SAFETY CHAIN P-004-433 460 VOLT, 3 PHASE P-004-783
    SAFETY CABLE, (64-3/4) P-004-386
    STEEL BRIDGE (12 X 72) P-003-572TRANSFORMER: (SELECT BY VOLTAGE AND PHASE)
    100VA transformers used on lifts with warning light or bell.
    CYLINDER: CURRENT STANDARD (5/88 TO DATE)230V, 24V, 1 PHASE P-001-845
    Lifts manufactured before 4/1/00 require an elbow part 240-460V, 24V, 3 PHASE  P-001-844
     # P-010-219 when replacing a complete cylinder assembly. 230V,24V,1 PHASE, WITH BELL OR LIGHT P-000-746
    COMPLETE CYLINDE
    RP-D-0024 240-460V,24V,3 PHASE WITH BELL OR LIGHT P-000-399
    CYLINDER PACKING KIT P-003-514
    CYLINDER HOUSING P-004-053CONTACTOR, MOTOR STARTER:
    CYLINDER ROD ASSEMBL
    YP-004-054 230V, 1 PHASE, CONTACTORP-000-414
    CYLINDER BEARING ASSEMBL
    YP-003-923 230V, 3 PHASE, CONTACTORP-000-413
    CYLINDER PISTON ASSEMBL
    YP-A-1409 460V, 3 PHASE, CONTACTORP-000-413
    CYLINDER PIN UPPE
    RP-A-1951
    CYLINDER PIN LOWER P-A-0209OVERLOAD:
    CYLINDER PIN SNAP RING 1 P-001-876 230V, 1 PHASE, OVERLOAD P-000-420
    FLOW CONTROL CARTRIDGE (BEFORE 4/00) P-001-302 230V, 3 PHASE, OVERLOAD P-000-418
    GREEN HEXAGONAL FLOW CONTROL (AFTER 4/00) P-015-396 460V, 3 PHASE, OVERLOAD P-000-417
    CYLINDER: (PRE 5/88) MOTOR: (SELECT BY VOLTAGE AND PHASE)
    COMPLETE CYLINDE
    RP-005-755 208/230V 1 PHASE P-001-327
    CYLINDER ROD ASSEMBL
    YP-005-756 208/230/460/480V 3 PHASE P-003-373
    UPPER CYLINDER PIN, (OLD STYLE) P-A-0226
    LOWER CYLINDER PIN, (OLD STYLE) P-A-0209OPTION:
    BELL AND TIMER KIT, 24V P-005-823
    HYDRAULIC: (COMMON TO ALL POWER UNITS)BELL AND TIMER KIT, 110V  P-005-825
    HYDRAULIC PUMP P-000-357 STROBE WARNING LIGHT, 24V P-000-805
    FLOW VALVE P-004-334 STROBE WARNING LIGHT, 110V P-001-422
    CHECK VALVE P-001-262 FLUID HEATER P-001-347
    24V DOWN SOLENOID VALVE AND COIL ASM P-001-259 BLUE SPRAY PAINT, 16 oz P-015-173
    24V DOWN SOLENOID COIL (ONLY) P-001-260 YELLOW SPRAY PAINT, 16 oz P-015-174
    24V/115V DOWN SOLENOID VALVE (ONLY) P-001-279 POWER UNIT DECAL KIT P-003-868
    115V DOWN SOLENOID AND COIL ASM P-001-296 COMPLETE DECAL KIT FOR 2000K P-003-993
    115V DOWN SOLENOID COIL (ONLY) P-001-297 LIMIT SWITCH ASSEMBL
    YP-003-898
    FLOW CONTROL VALVE (3.5 GPM) P-001-293 INSTALLATION KIT, 20 HOSE AND 10 GAL FLUI
    DP-006-400
    RELIEF VALVE P-001-263 OWNERS MANUAL P-003-566
    BREATHER CAP FOR RESERVOI
    RP-001-890 REPLACEMENT NAME/SERIAL NUMBER TAG P-001-448
     
    TO ORDER PARTS CALL 800-843-3625  
    OR E-MAIL [email protected] 
      
    						
    							 
     
    T SERIES PARTS LIST 
     
     
     
     
     
     
     
    TO ORDER PARTS CALL 800-843-3625  
    OR E-MAIL [email protected] 
     
     
    GENERAL DESCRIPTION PART # GENERAL DESCRIPTION PART #
    MECHANICAL: COMPLETE POWER UNIT:
    ROLLER WHEEL P-023-153 23O VOLT, 1 PH, 24VA, WITH PUSHBUTTON P-004-771
    WHEEL, BASE, PLATFORM PIN (1.25 X 3.75) P-A-0216 230 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-003-563
    WHEEL, BASE, PLATFORM PIN SNAP RING P-001-061 460 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-004-770
    MAIN AXLE PIN (1-3/4 x 6-7/8) P-A-0227
    MAIN AXLE PIN SNAP RING 1-3/4 P-001-063TRANSFORMER: (SELECT BY VOLTAGE AND PHASE)
    STEEL HANDRAIL WITH SAFETY CHAIN P-004-433 100VA transformers on lifts with a warning light or bell.
    SAFETY CABLE, (64-3/4) P-004-386 230V, 24V, 50VA, 1 PHASE P-001-845
    STEEL BRIDGE (12 X 72) P-003-572 240-460V, 24V, 50VA, 3 PHASE  P-001-844
    230V,24V, 100VA, 1 PHASE P-000-746
    CYLINDER: T-50608 ONLY240-460V,24V, 100VA, 3 PHASE P-000-399
    COMPLETE CYLINDER   P-D-12312
    CYLINDER PACKING KIT P-023-614CONTROL BOX. COMPLETE:
    CYLINDER HOUSING P-B-1404 230 VOLT, 1 PHASE P-004-790
    CYLINDER ROD ASSEMBL
    YP-023-168 230 VOLT, 3 PHASE P-003-966
    CYLINDER BEARING ASSEMBL
    YP-023-173 460 VOLT, 3 PHASE P-004-783
    CYLINDER PISTON P-A-9910
    CYLINDER PIN UPPER P-A-0219CONTACTOR, MOTOR STARTER:
    CYLINDER PIN LOWE
    RP-001-538 230V, 1PH, CONTACTORP-000-414
    CYLINDER PIN SNAP RING 1.25 P-001-063 230V, 3PH, CONTACTO
    RP-000-413
    FLOW CONTROL P-015-396 460V, 3PH, CONTACTO
    RP-000-413
    CYLINDER: ALL EXCEPT T-50608 OVERLOAD:
    COMPLETE CYLINDER   P-D-12311 230V, 1PH, OVERLOAD P-000-420
    CYLINDER PACKING KIT P-004-635 230V, 3PH, OVERLOAD P-000-418
    CYLINDER HOUSING P-B-1403 460V, 3PH, OVERLOAD P-000-417
    CYLINDER ROD ASSEMBL
    YP-023-168
    CYLINDER BEARING ASSEMBLY P-023-170MOTOR: (SELECT BY VOLTAGE AND PHASE)
    CYLINDER PISTON P-A-1551 208/230V 1 PHASE P-001-327
    CYLINDER PIN UPPE
    RP-A-0219 208/230/460/480V 3 PHASE P-003-373
    CYLINDER PIN LOWE
    RP-A-9899
    CYLINDER PIN SNAP RING 1.25 P-001-061OPTION:
    FLOW CONTROL P-015-396 BELL AND TIMER KIT, 24V P-005-823
    BELL AND TIMER KIT, 110V  P-005-825
    HYDRAULIC: (COMMON TO ALL POWER UNITS)STROBE WARNING LIGHT, 24V P-000-805
    HYDRAULIC PUMP P-000-357 STROBE WARNING LIGHT, 110V P-001-422
    FLOW VALVE P-003-457 FLUID HEATE
    RP-001-347
    CHECK VALVE P-001-262 BLUE SPRAY PAINT, 16 oz P-015-173
    24V DOWN SOLENOID VALVE AND COIL ASM P-001-259 YELLOW SPRAY PAINT, 16 oz P-015-174
    24V DOWN SOLENOID COIL (ONLY) P-001-260 POWER UNIT DECAL KIT P-003-868
    24V/115V DOWN SOLENOID VALVE (ONLY) P-001-279 COMPLETE DECAL KIT FOR T2000 P-023-582
    115V DOWN SOLENOID AND COIL ASM P-001-296 LIMIT SWITCH ASSEMBL
    YP-003-898
    115V DOWN SOLENOID COIL (ONLY) P-001-297 INSTALLATION KIT, 20 HOSE AND 5 GAL FLUID P-006-399
    FLOW CONTROL VALVE (3.5 GPM) P-001-293 REPLACEMENT NAME/SERIAL NUMBER TAG P-001-448
    RELIEF VALVE P-001-263
    BREATHER CAP FOR RESERVOI
    RP-001-890 
    						
    							 
     
    SERIES 2000K PARTS LIST 
     
     
     
     
     
    TO ORDER PARTS CALL 800-843-3625 
    OR E-MAIL [email protected] 
     
     
    GENERAL DESCRIPTION PART # GENERAL DESCRIPTION PART #
    MECHANICAL: TRANSFORMER: (SELECT BY VOLTAGE AND PHASE)
    WHEEL ASSEMBLY P-005-244 100VA transformers used on lifts with warnin
    g light or bell.
    WHEEL BASE & PLATFORM PIN (1-1/4 x 3-3/4) P-A-0216 230V, 24V, 1 PH P-001-845
    WHEEL, BASE AND PLATFORM PIN SNAP RING P-001-061 240-460V, 24V, 3 PHASE  P-001-844
    MAIN AXLE PIN (1-3/4 x 6-7/8) P-A-0227 230V,24V,1PH, WITH BELL OR LIGHT P-000-746
    MAIN AXLE PIN SNAP RING 1-3/4 P-001-063 240-460V,24V,3PH WITH BELL OR LIGHT P-000-399
    STEEL HANDRAIL WITH SAFETY CHAIN P-004-433
    SAFETY CABLE, (64-3/4) P-004-386CONTACTOR, MOTOR STARTER:
    STEEL BRIDGE (12 X 72) P-003-572 230V, 1PH, CONTACTO
    RP-000-693
    230V, 3PH, CONTACTO
    RP-000-692
    CYLINDER: CURRENT STANDARD (5/88 TO DATE)460V, 3PH, CONTACTOR P-000-692
    Lifts manufactured before 4/1/00 require an elbow part 
    # P-010-219 when replacing a complete cylinder assembly. OVERLOAD:
    COMPLETE CYLINDER P-D-1185 230V, 1PH, OVERLOAD P-000-701
    CYLINDER PACKING KIT P-003-514 230V, 3PH, OVERLOAD P-000-699
    CYLINDER HOUSING P-003-856 460V, 3PH, OVERLOAD P-000-696
    CYLINDER ROD ASSEMBL
    YP-005-731
    CYLINDER BEARING ASSEMBLY P-003-923MOTOR: (SELECT BY VOLTAGE AND PHASE)
    CYLINDER PISTON ASSEMBL
    YP-A-1409 208/230V 1 PHASE P-001-327
    CYLINDER PIN UPPER P-A-1951 208/230/460/480V 3 PHASE P-003-373
    CYLINDER PIN LOWE
    RP-A-0209
    CYLINDER PIN SNAP RING 1 P-001-876OPTION:
    FLOW CONTROL CARTRIDGE (BEFORE 4/00) P-001-302 BELL AND WARNING LIGHT COMBO. P-005-823
    GREEN HEXAGONAL FLOW CONTROL (AFTER 4/00) P-015-396 BELL AND LIGHT PROTECTIVE CAGE P-005-825
    FLUID HEATE
    RP-001-347
    CYLINDER: (PRE 5/88)BLUE SPRAY PAINT, 16 oz P-015-173
    COMPLETE CYLINDER P-005-651 YELLOW SPRAY PAINT, 16 oz P-015-174
    CYLINDER ROD ASSEMBL
    YP-003-919 POWER UNIT DECAL KIT P-003-868
    UPPER CYLINDER PIN, (OLD STYLE) P-A-0226 COMPLETE DECAL KIT FOR 2000K P-003-993
    LOWER CYLINDER PIN, (OLD STYLE) P-A-0209 LIMIT SWITCH ASSEMBL
    YP-003-898
    INSTALLATION KIT, 20 HOSE AND 5 GAL FLUID P-006-399
    HYDRAULIC: (COMMON TO ALL POWER UNITS)REPLACEMENT NAME/SERIAL NUMBER TAG P-001-448
    HYDRAULIC PUMP P-026-106
    24V DOWN SOLENOID COIL (ONLY) P-015-301
    24V/115V DOWN SOLENOID VALVE (ONLY) P-003-106
    BREATHER CAP FOR RESERVOI
    RP-001-890
    COMPLETE POWER UNIT: (SELECT BY VOLTAGE AND PHASE)
    23O VOLT, 1 PH, 24VA, WITH PUSHBUTTON P-004-771
    230 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-003-563
    460 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-004-770
    CONTROL BOX. COMPLETE: (SELECT BY VOLTAGE AND PHASE)
    230 VOLT, 1 PHASE P-004-790
    230 VOLT, 3 PHASE P-003-966
    460 VOLT, 3 PHASE P-004-783 
    						
    							 
     
     
    SERIES 3000 PARTS LIST 
     
     
    GENERAL DESCRIPTION PART # GENERAL DESCRIPTION PART #
    MECHANICAL: TRANSFORMER: (SELECT BY VOLTAGE AND PHASE)
    WHEEL ASSEMBLY P-005-244 100VA transformers used on lifts with warning light or bell.
    UPPER WHEEL PIN (1-1/4 X 3-3/4) P-A-0216 230V, 24V, 1 PH P-001-845
    LOWER WHEEL PIN (1-1/4 X 5-3/4) P-A-0390 240-460V, 24V, 3 PHASE  P-001-844
    WHEEL PIN SNAP RING 1-1/4 P-001-061 230V,24V,1PH, WITH BELL OR LIGHT P-000-746
    MAIN AXLE PIN (2 x 7) P-A-0379 240-460V,24V,3PH WITH BELL OR LIGHT P-000-399
    MAIN AXLE PIN SNAP RING 2 P-001-057
    BASE AND PLATFORM PIN (1-1/2 X 3-3/4) P-A-0216CONTACTOR, MOTOR STARTER:
    STEEL HANDRAIL WITH SAFETY CHAIN P-004-433 230V, 1PH, CONTACTOR P-000-414
    SAFETY CABLE, (64-3/4) P-004-386 230V, 3PH, CONTACTOR P-000-413
    STEEL BRIDGE (12 X 72) P-B-0190 460V, 3PH, CONTACTOR P-000-413
    CYLINDER: OVERLOAD:
    Lifts manufactured before 4/1/00 require an elbow part  230V, 1PH, OVERLOAD P-000-420
    # P-015-683 when replacing a complete cylinder assembly.  230V, 3PH, OVERLOAD P-000-418
    3200 COMPLETE CYLINDER P-D-1434 460V, 3PH, OVERLOAD P-000-417
    3200 CYLINDER PACKING KIT P-003-515
    3200 CYLINDER HOUSING P-004-267MOTOR: (SELECT BY VOLTAGE AND PHASE)
    3200 CYLINDER ROD ASSEMBLY P-004-268 208/230V 1 PHASE P-001-327
    3200 CYLINDER BEARING ASSEMBLY P-003-874 208/230/460/480V 3 PHASE P-003-373
    3200 CYLINDER PISTON ASSEMBL
    YP-A-1551
    3300 COMPLETE CYLINDER P-D-1435OPTION:
    3300 CYLINDER PACKING KIT P-003-516 BELL AND TIMER KIT, 24V P-005-823
    3300 CYLINDER HOUSING P-004-280 BELL AND TIMER KIT, 110V  P-005-825
    3300 CYLINDER ROD ASSEMBLY P-004-282 STROBE WARNING LIGHT, 24V P-000-805
    3300 CYLINDER BEARING ASSEMBLY P-004-284 STROBE WARNING LIGHT, 110V P-001-422
    3300 CYLINDER PISTON ASSEMBLY P-A-1552 FLUID HEATER P-001-347
    CYLINDER PIN (1 X 5-5/16) P-A-0226 BLUE SPRAY PAINT, 16 oz P-015-173
    CYLINDER PIN (1 X 7-5/16) P-A-0416 YELLOW SPRAY PAINT, 16 oz P-015-174
    CYLINDER PIN SNAP RING 1 P-001-876 POWER UNIT DECAL KIT P-003-868
    FLOW CONTROL CARTRIDGE (BEFORE 4/00) P-001-302 COMPLETE DECAL KIT FOR 3000 P-004-261
    GREEN HEXAGONAL FLOW CONTROL (AFTER 4/00) P-015-396 INSTALLATION KIT, 20 HOSE AND 10 GAL FLUID P-006-400
    OWNERS MANUAL P-003-566
    HYDRAULIC: (COMMON TO ALL POWER UNITS)PLUG 230V, 3 PHASE P-001-671
    HYDRAULIC PUMP P-000-357 PLUG 460V, 3 PHASE P-000-994
    FLOW VALVE P-004-334 PLUG 230V, 1 PHASE P-002-049
    CHECK VALVE P-001-262 PUSH BUTTON SWITCH P-000-802
    24V DOWN SOLENOID VALVE AND COIL ASM P-001-259 REPLACEMENT NAME/SERIAL NUMBER TAG P-001-448
    24V DOWN SOLENOID COIL (ONLY) P-001-260
    24V/115V DOWN SOLENOID VALVE (ONLY) P-001-279
    115V DOWN SOLENOID AND COIL ASM P-001-296
    115V DOWN SOLENOID COIL (ONLY) P-001-297
    FLOW CONTROL VALVE (3.5 GPM) P-001-293
    RELIEF VALVE P-001-263
    BREATHER CAP FOR RESERVOIR P-001-890
    COMPLETE POWER UNIT:
    23O VOLT, 1 PH, 24VA, WITH PUSHBUTTON P-004-896
    230 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-003-562
    460 VOLT, 3 PH, 24VA, WITH PUSHBUTTON P-004-895
    CONTROL BOX. COMPLETE:
    230 VOLT, 1 PHASE P-004-790
    230 VOLT, 3 PHASE P-003-966
    460 VOLT, 3 PHASE P-004-783
      
    TO ORDER PARTS CALL 800-843-3625  
    OR E-MAIL [email protected]  
    						
    							 
     
     
    SERIES 4000 PARTS LIST 
     
     
    GENERAL DESCRIPTION PART # GENERAL DESCRIPTION PART #
    MECHANICAL: COMPLETE POWER UNIT WITH PUSHBUTTON:
    4100,4200,4300,4400 INNER WHEEL P-A-0499 4100,4200,4300,4400, 230 VOLT, 3 PH, 24VA P-004-391
    4100,4200,4300,4400 OUTER WHEEL P-A-0500 4100,4200,4300,4400, 460 VOLT, 3 PH, 24VA P-005-485
    4100,4200,4300,4400 WHEEL PIN (1-3/4X6-7/8) P-A-0227 4100, 230 VOLT, 3 PH, 24VA (AFTER 1/00) P-006-983
    4100,4200,4300,4400 WHEEL PIN SNAP RING  P-001-063 4100, 460 VOLT, 3 PH, 24VA (AFTER 1/00) P-010-684
    4100,4200,4300,4400 MAIN AXLE PIN (2 x 9) P-A-0370
    4100,4200,4300,4400 MAIN AXLE PIN SNAP RING P-001-057CONTROL BOX. COMPLETE:
    4100,4200,4300,4400 BASE AND PLATFORM PIN P-A-0376 4100,4200,4300,4400, 230 VOLT, 3 PHASE P-005-489
    STEEL HANDRAIL ASSEMBLY P-004-446 4100,4200,4300,4400, 460 VOLT, 3 PHASE P-005-494
    SAFETY CABLE, (64-3/4) P-004-386 4100, 230V, 3 PHASE (AFTER 1/00) P-006-308
    STEEL BRIDGE (12 X 72) P-B-0191 4100, 460V, 3 PHASE (AFTER 1/00) P-007-202
    MECHANICAL: 4100 AFTER 1/1/2000 TRANSFORMER:
    4100 INNER WHEEL (AFTER 1/00) P-A-8206 240-460V,24V,3PH P-000-399
    4100 OUTER WHEEL (AFTER 1/00) P-A-8205
    4100 PLATFORM WHEEL PIN (AFTER 1/00) P-A-8203CONTACTOR, MOTOR STARTER: 
    4100 BASE FRAME WHEEL PIN (AFTER 1/00) P-A-8202 208,230,460,480V, 3PH, CONTACTOR P-000-413
    4100 BASE AND PLATFORM PIN (AFTER 1/00) P-A-8201
    OVERLOAD:
    CYLINDER: MODELS 4100, 4200, 4300, 4400230V, 3PH, OVERLOAD P-000-419
    Lifts manufactured before 4/1/00 require an elbow part 460V, 3PH, OVERLOAD P-000-763
     # P-015-683 when replacing a complete cylinder assembly.  230V, 3PH, OVERLOAD 4100 (AFTER 1/00) P-000-418
    COMPLETE CYLINDER P-D-0498 460V, 3PH, OVERLOAD 4100 (AFTER 1/00) P-000-417
    CYLINDER PACKING KIT P-004-365
    CYLINDER HOUSING P-004-361MOTOR:
    CYLINDER ROD ASSEMBLY P-004-363 208,230,460,480V 3 PHASE P-001-344
    CYLINDER BEARING ASSEMBLY P-004-364 208,230,460,480V 3 PHASE, 4100 (AFTER 1/00) P-003-373
    CYLINDER PISTON ASSEMBL
    YP-A-1551
    UPPER CYLINDER PIN (1 X 4-1/2) P-A-0410OPTIONS:
    LOWER CYLINDER PIN (1-1/4 X 3-3/4) P-A-0216 BELL AND TIMER KIT, 24V P-005-823
    CYLINDER PIN SNAP RING 1 P-001-876 BELL AND TIMER KIT, 110V  P-005-825
    CYLINDER PIN SNAP RING 1-1/4 P-001-061 STROBE WARNING LIGHT, 24V P-000-805
    STROBE WARNING LIGHT, 110V P-001-422
    CYLINDER: 4100 AFTER 1/1/00FLUID HEATER P-001-347
    4100 COMPLETE CYLINDER P-D-10162 BLUE SPRAY PAINT, 16 oz P-015-173
    4100 CYLINDER PACKING KIT P-004-365 YELLOW SPRAY PAINT, 16 oz P-015-174
    4100 CYLINDER HOUSING P-004-361 POWER UNIT DECAL KIT P-003-868
    4100 CYLINDER ROD ASSEMBLY P-006-971 COMPLETE DECAL KIT FOR 4000 P-004-375
    4100 CYLINDER BEARING ASSEMBLY  P-004-364 INSTALLATION KIT, 20 HOSE AND 15 GAL FLUID P-006-401
    4100 CYLINDER PISTON ASSEMBLY P-A-1551 OWNERS MANUAL P-003-566
    4100 UPPER CYLINDER PIN (1 X 4-1/2) P-A-0410 PLUG 230V, 3 PHASE P-001-671
    4100 LOWER CYLINDER PIN (1-1/4 X 3-3/4) P-A-0216 PLUG 460V, 3 PHASE P-000-994
    4100 CYLINDER PIN SNAP RING 1 P-001-876 PUSH BUTTON SWITCH P-000-802
    4100 CYLINDER PIN SNAP RING 1-1/4 P-001-061 PRESSURE LINE FILTER P-001-319
    REPLACEMENT NAME/SERIAL NUMBER TAG P-001-448
    HYDRAULIC: (COMMON TO ALL POWER UNITS)
    HYDRAULIC PUMP P-000-358
    HYDRAULIC PUMP 4100 (AFTER 1/00) P-007-114
    FLOW VALVE P-003-458
    CHECK VALVE P-001-262
    24V DOWN SOLENOID VALVE AND COIL ASM P-001-259
    24V DOWN SOLENOID COIL (ONLY) P-001-260
    24V/115V DOWN SOLENOID VALVE (ONLY) P-001-279
    115V DOWN SOLENOID AND COIL ASM P-001-296
    115V DOWN SOLENOID COIL (ONLY) P-001-297
     
    TO ORDER PARTS CALL 800-843-3625  
    OR E-MAIL [email protected]  
    						
    All Advance Lifts manuals Comments (0)