ADT Security Services Safewatch QuickConnect User Manual

– 21 – 
SECURING THE PREMISES 
    
Panic Keys / Chime Mode 
 
Panic Keys 
Your system may have been programmed to use special keys to manually activate panic functions. The 
functions that might be programmed are listed below. See your installer for the function(s) that may 
have been programmed for your system.  
   Your installer should 
note the functions 
that are active in 
your system.  
Active Panic Functions 
Keys Zone  Function 
1 and ✻ 95 
 
3 and #  96 
 
✻ and #  99 
  
To use a paired key...

– 22 – 
USER FUNCTIONS 
Message Recording/Playback/Volume Control 
The ADT Safewatch QuickConnect Security System 
    Message Center allows you to record, play and 
delete messages. The maximum message duration is 85 seconds. 
NOTES:  (1)  The Record/playback functions can only be performed from the master keypad.  It cannot be performed 
from any other wireless keypad (ex. 5827). 
  (2)  If the system loses electrical power, all messages will be erased. 
  (3)  Message Play/Record will not be...

– 23 – 
USER FUNCTIONS 
Message Recording/Playback/Volume Control 
 
Adjusting the Volume 
The volume level of message playback, system announcements, and status beeps can be changed. You 
can also mute system announcements if desired. 
 
To adjust message playback/system announcement volume: 
 
FUNCTION  + VOLUME + [3] or [6] †      
† [3] = increases volume one level, [6] = decreases volume one level. 
 
Repeat the key sequence until the desired volume level is achieved. 
 
To mute system...

– 24 – 
USER FUNCTIONS 
AUX Function 
 
General Information 
The AUX key may have been programmed to either perform a predefined function.  Ask your installer 
which function has been assigned for your system. 
 
AUX Key:     
PRE-DEFINED FUNCTION    
 
If programmed for the AUX function, you can use the 
AUX key to activate a string of up to 20 
keystrokes that have been stored in the system’s memory.  Typical functions include: 
 • Seldom used but repeatable sequences 
 • Arming sequences that involve...

– 25 – 
USER FUNCTIONS 
Clock/Calendar 
 
Your system can display the current time (see your installer). The date is not displayed, but has an 
internal function. The system must be disarmed. 
To set the time and date:
                         + FUNCTION  +  [63] 
  Master user code or  
 Installer Code 
 
The system will enter the Voice Prompt Calendar Setting mode. The [#] key can be pressed at 
any time to repeat a voice prompt. 
 NOTES:   1.  The keypad beeps twice for invalid data entries (e.g., an...

– 26 – 
USER FUNCTIONS 
Clock/Calendar 
  
5.  The system will announce, “Enter two-digit day press ADD to accept, ESCAPE to quit”. 
Day
        01 (The current day of the month will display.) 
Enter the 2-digit day of the month (i.e., 01-31). 
Press [ADD] to accept the entry and continue to the year setting. 
Press [ESCAPE] to back up to Month selection. 
 
6.  The system will announce, “Enter two-digit year press ADD to accept, ESCAPE to quit”. 
Year    08   
 (The current year will be displayed.)...

– 27 – 
USER FUNCTIONS 
Remote Phone Control Feature 
 
The ADT Safewatch QuickConnect Security System 
    is equipped with a remote interactive phone 
capability that permits access to the security system from any off-site touch-tone telephone using all 
user codes. If this feature has been programmed, the system will provide the appropriate voice 
messages and any system beeping sounds indicating the status of the security system over the phone 
line. (Refer to Summary of Audible Notification for...

– 28 – 
USER FUNCTIONS 
Remote Phone Control Feature 
 
Enter:                        (within eight seconds) 
  Your user code 
Upon entering remote phone control mode the ADT Safewatch QuickConnect Security System 
    will 
announce “System, enter code”. 
Remote Phone Control Commands 
 
To remotely disarm system: 
                       + [1] 
  Your user code 
To remotely arm in AWAY mode:                        + [2] 
  Your user code 
To remotely arm in STAY mode:                        + [3]...

– 29 – 
USER FUNCTIONS 
Speaker Phone Feature  
If this feature has been programmed, the ADT Safewatch QuickConnect Security System 
    is capable 
of operating as a speaker phone. During speaker phone operation, the system will provide the following 
functions: 
• All function/event processing will continue to operate, but there will be no announcements. 
• The ARMED (red) and READY (green) LEDs will alternately blink. 
• “PH” will be displayed. 
NOTE:  The system will enter the Speaker Phone mode...

– 30 – 
USER FUNCTIONS 
Speaker Phone Feature 
 
ADT Safewatch 
    QuickConnect Security System Speaker Phone Functions 
To place a call using the Speaker Phone:  
[#] + AUX and dial the desired phone number. 
To answer a call using the Speaker Phone: 
[#] + AUX  
To flash (switch between two calls using call waiting): 
AUX  
To hang up:  
OFF   
To activate/deactivate (toggle) ringer:  
[#] +  VOLUME  +  AUX  
To return the keypad to telephone mode after disarming the system: 
[#] + AUX  
NOTES:   (1)...