ADT Security Services Safewatch Pro 3000 User Manual

							– 31 –
$FFHVVLQJ2WKHU3DUWLWLRQV&RQWLQXHG
8VLQJWKH*R7R&RPPDQG
If the user is authorized, a touchpad in one partition can be used to perform system
functions in the other partition by using the GOTO command.
·
You must use a Custom English touchpad to access another partition.
·
Touchpads automatically return to their original partition after 2 minutes
with no touchpad activity.
1.  
          +  [*
] + partition number (0,1,2,3)
(Security Code)
0 = return to touchpad’s original partition.
1 = partition 1; 2 = partition 2; 3 = common zone
The touchpad beeps to confirm the partition change.
 (-7%61)(
6)%(= 83 %61
English Display: READY
2.The touchpad remains in the new partition until
directed to go to another partition, or until it
automatically returns to the original partition.
The active partition number is displayed in the upper
left portion of screen, if the option is programmed. (-7%61)(
6)%(= 83 %61
English Display: READY
0XOWL3DUWLWLRQ$UPLQJ
Some users can be given Multi-Partition arming ability by being assigned to both
partitions when programming user attributes.
When attempting to arm multi-partitions:
·
You must use a Custom English touchpad.
·
The system arms only if all partitions are “ready to arm.”
·
If any partition is “not ready,” the system does not arm at all.
·
You can use the GOTO command to bypass open zones before arming.
·
If any partition is already armed when global arming is attempted, that
partition remains in its existing armed state.
  
          +  [0] + arm command (see list below)
(Security Code)
Multi-Partition Arming Commands
2 = arms all partitions AWAY
3 = arms all partitions STAY
33 = arms all partitions NIGHT-STAY
7 = arms all partitions INSTANT
1 = disarms all partitions
 (-7%61)(
6)%(= 83 %61
English Display: READY 
						

							– 32 –
$FFHVVLQJ2WKHU3DUWLWLRQV&RQWLQXHG
&RPPRQ=RQH2SHUDWLRQ
Ask your installer if a
common zone was
assigned. If so, check
this box      
Your system may have been set up to use a common zone, which is
an area shared by users of both partitions, such as a foyer or lobby.
If so, please note the following:
·
The common zone will sound and report alarms only when both
partitions are armed. If only one partition is armed, the system
ignores faults on the common zone.
·
Either partition may arm its system if the common zone is
faulted, but once armed, the other partition will not 
be able to
arm unless the common zone is first bypassed or the fault is
corrected.
·
Faults on the common zone are displayed on common zone
touchpads, and will also appear on another partition’s touchpad
when that partition is armed.
·
Either partition can clear and restore the common zone after an
alarm.
·
Entry/exit time for the common zone is the same as for partition 1. 
						

							– 33 –
6FKHGXOLQJ
$ERXW6FKHGXOLQJ
The system provides up to 16 end-user schedules (programmable by master/installer
only), which can be used to control various types of events.
·
 Each schedule causes a defined event to start and stop (when appropriate) at a
specified time.
·
 Schedules can be set to automatically repeat at various intervals.
·
 Schedules can be set for random starting, if desired.
&UHDWLQJ6FKHGXOHV
1.            +  [#] + [6] [4]
(Master Code)
 (-7%61)(
6)%(= 83 %61
2.Enter a 2-digit schedule number from 01-16.
Press [*
] to continue.)28)6 7,)( 23

=59-8 
3.Enter the desired 2-digit event number from the
following list.
00 = clear the scheduled event
01 = turn a programmed output on or off)28)6 ):)28
(see Using Device Commands section for a list of output device numbers used
in your system)
02 = set a user access schedule for one or more users
(see Security Codes section for an explanation of access groups)
03 = send a “latch-key” report to a pager if the system is not disarmed by a specified
time; message sent is “777-7777.”
04 = automatically arm the system in STAY mode at a specified time (pager report
also sent)
05 = automatically arm the system in AWAY mode at a specified time (pager report
also sent)
06 = automatically disarm the system at a specified time (pager report also sent)
07 = Display the word “REMINDER” at a specified time
Press [*
] to continue.
4. For event number “01,” enter the output number
associated with this schedule.
Otherwise, this prompt is skipped.
Press [*
] to continue to the “Start” prompt below.
():-) 291&)6

						

							– 34 –
6FKHGXOLQJFRQWLQXHG
5. For event number “02,” enter the access group
number. Otherwise, this prompt is skipped.
Press [*
] to continue to the “Start” prompt below.+6394 291&)6
<
6. For event numbers “03-07,” enter the partition
number to be armed or disarmed.
0 = arm all; 1 = partition 1; 2 = partition 2;
3 = arm common
Otherwise, this prompt is skipped.
Press [*
] to continue to the “Start” prompt.4%68-8-32
<
7. Enter the event’s start time and days of week.
Hour = 00-23; minute = 00-59
AM = 0; PM = 1
Days = Position the cursor under the desired days
using the [*
] key to move forward, then press “1” to
select the day.
Press [*
] to continue.78%68 718;8*7
,,11%1 
8. Enter the event’s stop time, AM/PM and days of week.
Refer to step 7 for available entries.
Press [*
] to continue.7834 718;8*7
,,11%1 
9. Enter the desired repeat option.
0 = no repeat
1 = repeat schedule weekly
2 = repeat schedule biweekly (every other week)
3 = repeat schedule every third week
4 = repeat schedule every fourth week
e.g., To make a schedule that happens everyday you
would select all days with a repeat count of 1. To make
a schedule that runs for one week then stops, select
everyday with a repeat count of 0.6)4)%8 348-32
 <
10. Select the randomize option, if desired.
0 = no; 1 = yes
If selected, the schedule times will vary within 60
minutes of the “hour” time. For example, if a
schedule is set to start at 6:15pm, it will do so the
first time 6:15pm arrives, but on subsequent days it
will start anytime between 6:00 and 6:59 p.m.
Press [*
] to continue.6%2(31->)

=23 
==)7 < 
						

							– 35 –
(YHQW/RJJLQJ3URFHGXUHV
$ERXW(YHQW/RJJLQJ
The system records various events in a history log, which can be viewed by the master
user using a Custom English Display touchpad.
·
 The Event Log holds up to 100 events.
·
 Events are displayed in chronological order, from most recent to oldest.
·
 When the log is full, the oldest event is replaced by the logging of any new event.
9LHZLQJWKH(YHQW/RJ
1.            + [#] +    6  +   0 
(Master Code)
(-7%61)(
6)%(= 83 %61
2. The system displays the most recent event as follows:
·
 event number
·
 type of event, identified by its corresponding code
(see your installer for the meaning of each code)
·
 zone or user number (depending on type of event)
·
 partition in which event occurred
·
 time and date of the event’s occurrence.
3. Pressing [*
] displays previous events (back in time).
Pressing [#] displays events forward in time.
4. Exit the event log by pressing any key other than [*
]
or [#]. ) 9 4
%1  
						

							– 36 –
7HVWLQJWKH6\VWHP7R%H&RQGXFWHG:HHNO\
$ERXW7HVWLQJWKH6\VWHP
The TEST key puts your system into the Test mode, which allows each protection
point to be checked for proper operation.
·
The touchpad sounds a single beep every 40 seconds as a reminder that the
system is in the Test mode.
·
Alarm messages are not sent to your Customer Care Center while Test mode is on.
1  Disarm the system and close all protected windows,
doors, etc. The READY indicator light should come
on if all zones are intact (i.e., all protected windows,
doors, etc. are closed.
(-7%61)(
6)%(= 83 %61
2.            +    5   then  [0] (walk)
(Security Code)TEST
The Dial test (option “1”) is intended for the installer
and should not be used unless directed to do so by
your Customer Care Representative.
=
(-%0
=
;%0/
3. Listen. The external sounder should sound for 1
second and then turn off. If the sounder does not
sound, CALL FOR SERVICE.8)78 -2
463+6)77
 4. Fault zones. Open each protected door and window in turn and listen for three
beeps from the touchpad. Identification (zone number or zone description) of each
faulted protection point should appear on the display. The display clears when the
door or window is closed.
5. Walk in front of any interior motion detectors (if used) and listen for three beeps.
The identification of the detector should appear on the display when it is activated.
The display clears when no motion is detected.
Note that if wireless motion detectors are used, there is a 3-minute delay between
activations. This is to conserve battery life.
6. Test all smoke detectors, following the manufacturers instructions. The
identification of each detector should appear on the display when each is activated.
If a problem is experienced with any protection point (no confirming sounds, no
display), call for service immediately.
When all protection points have been checked and are intact (closed), there should
be no zone identification numbers displayed on the touchpad.
7. Exit test mode:
   
                + [1]
(Security Code)
If the test mode is inadvertently left active, it automatically turns off after 4 hours. 
						

							– 37 –
7URXEOH&RQGLWLRQV
Check and
Battery Displays
 * Not all systems
use wireless
sensors.
The word 
CHECK on the touchpads display, accompanied by a
beeping at the touchpad, indicates a trouble condition in the
system.
To silence the beeping for these conditions, press any key.
1.
A display of CHECK and one or more zone numbers
indicates that a problem exists with the displayed zone(s) and
requires your attention. Determine if the zone(s) displayed are
intact and make them so if they are not. If the problem has been
corrected, the display can be cleared if you enter the OFF
sequence (security code plus OFF key) twice. If the display
persists, CALL FOR SERVICE
.
Note: A display of 
CHECK 70 on English Display touchpads
indicates that the wiring connection to the external sounder is
at fault (opened or shorted), and you should CALL FOR
SERVICE. See “BELL FAILURE” on next page. A display of
CHECK 90 indicates that RF interference may be impeding the
operation of wireless sensors* in the system. See “
Rcvr Jam”
on next page.
2.
If there are wireless sensors* in your system, the 
CHECK
condition may also be caused by some change in the
environment that prevents the wireless receiver from hearing a
particular sensor.  CALL FOR SERVICE if this occurs.
IF YOU CANNOT CORRECT A CHECK DISPLAY,
CALL FOR SERVICE.
TYPICAL CHECK DISPLAYS
06
CHECK
        AC
ENGLISH DISPLAY
TOUCHPAD
,)/
&)(6331;-2(3;
CUSTOM ENGLISH DISPLAY
TOUCHPAD 
						

							– 38 –
7URXEOH&RQGLWLRQV&RQWLQXHG
Words or letters in parentheses (   ) are those that are
displayed on English Display touchpads.
Other Trouble
Displays
*Any “beeping” that
accompanies a trouble
display can be stopped
by depressing any key
on the touchpad or by
entering an OFF
sequence (code + OFF)
 **    Not all systems use
  wireless sensors.
COMM. FAILUREIndicates that a failure has occurred in
(or FC) the telephone communication portion of
your system.
CALL FOR SERVICE.
SYSTEM LO BATIndicates that a low system battery
(or BAT with no condition exists.  Display is
zone No.) accompanied by beeping* at the
touchpad. If this condition persists for
more than one day (with AC present),
CALL FOR SERVICE.
LO BATIndicates that there is a low battery
+ zone descriptor condition in the wireless transmitter**
(or BAT with number displayed (00 is RF keypad).
zone No.) Accompanied by a single beep*
 (once
every 40 seconds) at the touchpad.
Either replace the battery yourself, or
CALL FOR SERVICE.  If the battery is
not replaced within 30 days, a CHECK
display may occur.
Rcvr JamWireless part of the system is experiencing
(or CHECK 90) RF interference which may impede
reception from wireless sensors.**
MODEM COMM
(or CC)Indicates that the control is on-line with
the Customer Care Centers remote
computer.
The control will not operate while on-line.
Wait a few minutes — the display should
disappear.
BELL FAILUREIndicates that the wiring connection to
(or CHECK 70) the external sounder is at fault (open or
shorted). Accompanied by “beeping” at
the touchpad. CALL FOR SERVICE. 
						

							– 39 –
7URXEOH&RQGLWLRQV&RQWLQXHG
Other Trouble
Displays
(Continued)AC LOSSThe system is operating on battery power
(or NO AC)
only due to an AC power failure.
If only some lights are out on the premises,
check circuit breakers and fuses and reset o
r
replace as necessary.
If AC power cannot be restored and a “low
system battery” message appears (see item 
2
on the previous page), CALL FOR
SERVICE.
Busy-Standby
(or dI)If this message remains displayed for more
than 1 minute, system is disabled. CALL
FOR SERVICE.
OPEN CIRCUIT  The touchpad is not receiving signals from
(or OC) the control. CALL FOR SERVICE.
Long Rng TrblIf part of your system, back-up Long
(or bF) Range Radio communication has failed.
CALL FOR SERVICE.
TELCO FAULT   The telephone line has a problem.
(or CHECK 94) CALL FOR SERVICE.
Total Power FailureIf there is no touchpad display at all, and the READY indicator
is not lit, operating power (from AC and back-up battery) for the
system has stopped and the system is inoperative. CALL FOR
SERVICE.
In The Event Of Telephone Operational Problems
In the event of telephone operational problems, disconnect the control from the phone line by
removing the plug from the phone wall jack. We recommend that your installer demonstrate this
disconnection on installation of the system. Do not attempt to disconnect the phone connection
inside the control. Doing so will result in the loss of your phone lines. If the regular phones work
correctly after the control 
has been disconnected from the phone wall jack, the control has a
problem and you should immediately call for service. If upon disconnection of the control, there is
still a problem on the phone line, notify the Telephone Company that they have a problem and
request prompt phone repair service. The user may not under any circumstances attempt any
service or repairs to the security system. Repairs must be made only by ADT authorized service
(see the LIMITED WARRANTY statement for information on how to obtain service). 
						

							– 40 –
0DLQWDLQLQJ