ADT Security Services iCenter 8132 User Manual

							Maintaining Your System (Contd) 
71 
 SCREEN ACTION 
 
 
 4.  Press the CLEAN SCREEN button. A 
window indicating “Touch Screen will be 
disabled so that you may wipe the screen 
clean. Please use a damp, soft cloth. DO 
NOT use any liquids, sprays, or ammonia-
based cleansers. Press CONTINUE to 
disable touch screen.”  
W hen the Continue button is pressed the 
“Touch Screen Disabled for ➙
➙➙ ➙ 30 Seconds”.  
During these 30 seconds the touch screen 
should be wiped clean of fingerprints using a 
mild soap solution and a soft cloth.  W hen the 
counter reaches zero, the window 
automatically closes and the touch screen is 
active. 
NOTE: Do not spray cleaning agent directly on 
the screen, spray it on cloth, then wipe surface 
area. 
 
 
Routine Care 
• Treat the components of your security system as you would any other electrical 
equipment. Do not slam sensor-protected doors or windows. 
• Keep dust from accumulating on the Touchpad and all protective sensors, 
particularly on motion sensors and smoke detectors. 
The Touchpad and sensors should be cleaned carefully with a dry soft cloth. 
Do not 
Do not Do not  Do not 
spray wate r or any othe r fluid on the  units.
spray wate r or any othe r fluid on the  units.spray wate r or any othe r fluid on the  units. spray wate r or any othe r fluid on the  units. 
     
						

							Maintaining Your System (contd) 
72 
  
						

							 
73 
 
Glossary 
 
The following terms are used throughout the guide. 
Arm/Disarm: 
Arm/Disarm: Arm/Disarm:  Arm/Disarm: “Armed” simply means that the burglary portion of your system is 
turned ON and is in a state of readiness. “Disarmed” means that the burglary 
system is turned OFF, and must be rearmed to become operational. However, even 
in a “disarmed” state, “emergency” and “fire” portions of your system are still 
operational. 
Bypass:
Bypass:Bypass: Bypass: To disarm a specific area of burglary protection while leaving other areas 
operational. 
Day/Night Zone
Day/Night ZoneDay/Night Zone Day/Night Zone: An area of protection whose violation causes a trouble indication 
during the disarmed (DAY) mode and an alarm during the armed (NIGHT) mode. 
Delay Zone:
Delay Zone:Delay Zone: Delay Zone: An area of protection containing doors most frequently used to enter or 
exit (typically, a front door, back door, or door from the garage into the building). 
The delay zone allows sufficient time for authorized entry or exit without causing an 
alarm. Consult your installer for the entry and exit delay times that have been set 
for your system during installation and record them on the separate sheet provided 
in this guide. 
Touchpad:
Touchpad:Touchpad: Touchpad: This is the area on your Touchpad containing numbered pushbuttons 
similar to those on telephones or calculators. These keys control the arming or 
disarming of the system, and perform other functions that were previously 
described in this manual. 
Master Code:
Master Code:Master Code: Master Code:  A 4-digit code that gives users access to all of the system’s functions, 
except unattended downloading (installer only). See also “User Code. 
Partition:
Partition:Partition: Partition: An independent group of zones that can be armed and disarmed without 
affecting other zones or users. 
User Code:
User Code:User Code: User Code: A 4-digit code that gives users access to the system’s basic functions. 
See also “Master Code.” 
Zone:
Zone:Zone: Zone: A specific area of protection.  
						

							Glossary (Contd) 
74 
 
  
						

							 
75 
  UL NOTICE: This is a “GRADE A” system. 
“FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT” 
This equipment has been tested to FCC requirements and has been found acceptable for use.  The FCC requires 
the following statement for your information: 
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict 
accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has 
been type tested and found to comply with the limits for a Class B computing device in accordance with the 
specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such 
interference in a residential installation.  However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures: 
   If using an indoor antenna, have a quality outdoor antenna installed. 
   Reorient the receiving antenna until interference is reduced or eliminated.  
   Move the receiver away from the control/communicator.   
   Move the antenna leads away from any wire runs to the control/communicator.   
   Plug the control/communicator into a different outlet so that it and the receiver are on different branch 
circuits. 
If necessary, the user should consult the dealer or an experienced radio/television technician for additional 
suggestions.  
The user or installer may find the following booklet prepared by the Federal Communications Commission helpful:  
“Interference Handbook”   
This booklet is available from the U.S. Government Printing Office, W ashington, DC 20402. 
 
The user shall not make any changes or modifications to the equipment unless authorized by the Installation 
Instructions or User’s Manual.  Unauthorized changes or modifications could void the user’s authority to operate 
the equipment. 
 
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS 
In the event of telephone operational problems, disconnect the control by removing the plug from the RJ31X 
(CA38A in Canada) telephone wall jack. W e recommend that your certified installer demonstrate disconnecting the 
phones on installation of the system. Do not disconnect the phone connection inside the control/communicator. 
Doing so will result in the loss of your phone lines. If the regular phone works correctly after the 
control/communicator has been disconnected from the phone lines, the control/communicator has a problem and 
should be returned for repair. If upon disconnection of the control/communicator, there is still a problem on the 
line, notify the telephone company that they have a problem and request prompt repair service. The user may not 
under any circumstances (in or out of warranty) attempt any service or repairs to the system. It must be returned to 
the factory or an authorized service agency for all repairs.  
						

							 
76 
  FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 NOTICE 
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that 
contains, among other information, the FCC registration number and ringer equivalence number (REN) for this 
equipment. If requested, this information must be provided to the telephone company. 
This equipment uses the following jacks: 
  An RJ31X is used to connect this equipment to the telephone network. 
The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive 
RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not 
all areas, the sum of the RENs should not exceed five (5.0). To be certain of the number of devices that may be 
connected to the line, as determined by the total RENs, contact the telephone company to determine the 
maximum REN for the calling area. 
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that 
temporary discontinuance of service may be required. If advance notice is not practical, the telephone company 
will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC 
if you believe necessary. 
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect 
the operation of the equipment. If this happens, the telephone company will provide advance notice in order for 
you to make the necessary modifications in order to maintain uninterrupted service. 
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. 
If the trouble is causing harm to the telephone network, the telephone company may request you remove the 
equipment from the network until the problem is resolved. 
There are no user serviceable components in this product, and the manufacturer must make all necessary repairs. 
Other repair methods may invalidate the FCC registration on this product. 
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is 
subject to state tariffs. 
This equipment is hearing-aid compatible. 
W hen programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for 
the call. Perform such activities in the off-peak hours; such as early morning or late evening.  
						

							 
77 
 CANADIAN DEPARTMENT OF COMMUNICATIONS  (DOC) STATEMENT 
NOTICE 
The Canadian Department of Communications label 
identifies certified equipment. This certification means that 
the equipment meets certain telecommunications network 
protective, operational and safety requirements. The 
Department does not guarantee the equipment will 
operate to the user’s satisfaction. 
Before installing this equipment, users should ensure that 
it is permissible to be connected to the facilities of the 
local telecommunications company. The equipment must 
also be installed using an acceptable method of 
connection. In some cases, the company’s inside wiring 
associated with a single line individual service may be 
extended by means of certified connector assembly 
(telephone extension cord). The customer should be 
aware that compliance with the above conditions may not 
prevent degradation of service in some situations. 
Repairs to certified equipment should be made by an 
authorized Canadian maintenance facility designated by 
the supplier. Any repairs or alterations made by the user 
to this equipment, or equipment malfunctions, may give 
the telecommunications company cause to request the 
user to disconnect the equipment. 
Users should ensure for their own protection that the 
electrical ground connections of the power utility, 
telephone lines and internal metallic water pipe system, if 
present, are connected together. This precaution may be 
particularly important in rural areas. 
Caution:  User should not attempt to make such 
connections themselves, but should contact the 
appropriate electric inspection authority, or electrician, as 
appropriate. 
The Load Number
 (LN) assigned to each terminal device 
denotes the percentage of the total load to be connected 
to a telephone loop which is used by the device, to 
prevent overloading. The termination on a loop may 
consist of any combination of devices subject only to the 
requirement that the total of the Load Numbers of all the 
devices does not exceed 100.
  
AVIS 
L’étiquette du ministère des Communications du Canada 
identifie le matériel homologué.  Cette étiquette certifie que le 
matériel est conforme à certaines normes de protection, 
d’exploitation et de sécurité des réseaux de 
télécommunications. Le ministère n’assure toutefois pas que 
le matériel fonctionnera à la satisfaction de l’utilisateur. 
Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il 
est permis de le raccorder aux installations de l’entreprise 
locale de télécommunications. Le matériel doit également 
être installé en suivant une méthode acceptée de 
raccordement. Dans certains cas, les fils intérieurs de 
l’entreprise utilisés pour un service individuel à la ligne 
unique peuvent être prolongés au moyen d’un dispositif 
homologué de raccordement (cordon prolongateur 
téléphonique interne). L’abonné ne doit pas oublier qu’il est 
possible que la conformité aux conditions énoncées ci-
dessus n’empèchet pas la dégradation du service dans 
certaines situations. Actuellement, les entreprises de 
télécommunications ne permettent pas que l’on raccorde leur 
matériel aux  prises d’abonnés, sauf dans les cas precis 
prévus par les tarifs particuliers de ces entreprises. 
Les réparations du matériel homologué doivent être 
effectuées pas un centre d’entretien canadien autorisé 
désigné par le fournisseur. La compagnie de 
télécommunications peut demander à l’utilisateur de 
débrancher un appareil à la suite de réparations ou de 
modifications effectuées par l’utilisateur ou à cause de 
mauvais fonctionnement. 
Pour sa propre protection, l’utilisateur doit s’assurer que tous 
les fils de mise en terre de la source d’énergie électrique, 
des lignes téléphoniques de réseau de conduites d’eau s’il y 
en a, soient raccordés ensemble. Cette précaution est 
particulièrement importante dans les régions rurales. 
Avertissement:  L’utilisateur ne doit pas tenter de faire ces 
raccordements lui-même; il doit avoir recours à un service 
d’inspection des installations électriques, ou à un électricien, 
selon le cas. 
L’indice de charge 
(IC) assigné à chaque dispositif terminal 
pour éviter toute surcharge indique le pourcentage de la 
charge totale qui peut être raccordé à un circuit  téléphonique 
bouclé utilisé par ce dispositif. La terminaison du circuit 
bouclé peut être constituée de n’importe quelle combinaison 
de dispositifs, pourvu que la somme des indices de charge 
de l’ensemble des dispositifs ne dépasse pas 100.
 
 
  
						

							 
78 
 
LIMITED WARRANTY 
Terms and Conditions Applying to Sale of Equipment 
1.    Limited W arranty.  
Any part of the system, including the wiring, installed under this Agreement which proves to be defective in material or 
workmanship within 90 days of the date of completion of installation will be repaired or replaced at ADTs option with a 
new functionally operative part. Labor and material required to repair or replace such defective components or to make 
mechanical adjustments to the system will be free of charge for a period of 90 days following the completion of the 
original installation. 
This warranty is extended only to the original consumer purchaser of the system and may be enforced only by such 
person. 
To obtain service under this warranty, call or write our local ADT Service Department at the telephone number or 
address found in your local yellow pages. 
Service pursuant to the warranty will be furnished only during ADTs normal working hours 8:00A.M. to 4:30P.M., 
Monday through Friday, except holidays. Services rendered outside the normal working hours of ADT are not within the 
scope of this warranty and any services requested to be performed at such times shall be charged for at ADTs then 
applicable rates for labor and material. 
This warranty does not apply to the conditions listed below, and in the event customer calls ADT for service under the 
warranty and upon inspection it is found that one of these conditions has led to the inoperability or apparent inoperability 
of the system, a charge will be made for the service call of the ADT representative, whether or not he actually works on 
the system. Should it actually be necessary to make repairs to the system due to one of the conditions Not Covered By 
W arranty, a charge will be made for such work at ADTs then applicable rates for labor and material. 
Conditions Not Covered By Warranty.   
A. Damage from accidents, acts of God, alterations, misuse, tampering or abuse.  B. Failure of the customer to properly 
close or secure a door, window, or other point protected by a burglar alarm device.  C. Failure of customer to properly 
follow operating instructions provided by ADT at time of installation or at a later date.  D. Trouble in leased telephone.  
E. Trouble due to interruption of commercial power.  F. Battery replacements. 
This warranty is in lieu of all other express warranties. Any implied warranties of merchantability and fitness for a 
particular purpose are limited in duration to a period of 90 days from the date of completion of installation. The exclusive 
remedy of the customer hereunder shall be repair or replacement as stated above. Under no circumstances shall ADT 
be liable to the customer or any other person for incidental or consequential damages of any nature, including without 
limitation, damages for personal injury or damages to property, and, however occasioned, whether alleged as resulting 
from breach of warranty by ADT, the negligence of ADT, or otherwise, ADTs liability will in no event exceed the 
purchase price of the system. Some states may not allow limitations on how long an implied warranty lasts, or the 
exclusion or limitations of incidental or consequential damages, so the above limitations and exclusions may not apply 
to you, unless a longer period is required by applicable law. Any action against ADT in connection with a system must 
be commenced within one year after the cause of action has occurred. 
No agent, employee or representative of ADT nor any other person is authorized to modify this warranty in any respect. 
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 
2. Installation. 
ADT agrees to install the equipment in a workmanlike manner in accordance with the following conditions:  
A. Customer will make premises available without interruption during ADT normal working hours 8:00A.M. to 4:30P.M., 
Monday through Friday, except Holidays.  B. Customer understands that the installation will necessitate drilling into 
various parts of the premises: ADT intends, generally, to conceal wiring in the finished areas of the premises; however, 
there may be areas which, due to construction, decoration, or furnishing of the premises, ADT determines, in its sole 
discretion, that it would be impractical to conceal wiring and, in such cases, wiring will be exposed.  C. Customer agrees 
to provide 110 VAC electrical outlets at designated locations for equipment requiring AC power.  D. Customer to provide 
for lifting and replacing carpeting, if required, for installation of floor mats or wiring. 
–––––––––––––––––––––––––––––––   ALL RIGHTS RESERVED  –––––––––––––––––––––––––––––– 
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form, or by any means – 
electronic, mechanical, photocopying, recording, or otherwise without the written permission of ADT Security Systems, Inc. 
The material in this publication is for information purposes and subject to change without notice. ADT Security Systems, Inc. 
assumes no responsibility for any errors which may appear in this publication. 
  
						

							 
79 
 
NOTES 
						

							 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
•••••••••••••••••••••••••••••••••••••••
  ADT Security Services, Inc.  One Town Center Rd.  Boca Raton, FL  33486 
 
Copyright © 2004 
 
ÊK5763
ÊK5763ÊK5763 ÊK5763-
-- -1V2ÇŠ
1V2ÇŠ1V2ÇŠ 1V2ÇŠ 
    
K5763-1V2  6/04 Rev. A