ADT Security Services BHS 1202 User Manual

11
TURNING SYSTEM ON WITH MOTION OFF AND DOORS INSTANT
This feature allows you to turn the system on without the motion detector
and remove the delay time from designated entry/exit doors.
1. You may combine the above features by pressing ON, MOTION
OFF, INSTANT.
2. The display window will show ON, INSTANT, MOTION OFF. The
red ON light will be lighted, confirming the system is ON.
3. You may now move freely within your home without tripping the
alarm.
USING THE KEYPAD’S EMERGENCY BUTTONS:
1. If you are...

12
USING SYSTEM OPTIONS KEY
The system has five options:  BYPASS, DOOR CHIME, AUXILIARY
CODES, ALARM MEMORY, AND TEST.
You may scroll through the options by pressing the OPTIONS key until the
desired option is displayed.
If you select a feature in error, you may cancel the selection by pressing
CANCEL.
BYPASS
This option allows you to bypass a trouble zone or a specific zone of your
choice. When bypassed, the system ignores the specified zone.
1. Press OPTIONS until the display window shows BYPASS,...

13
ADDING AUXILIARY CODES
This feature allows you to add up to six extra codes to turn the system on
and off. You can use auxiliary codes when you want to allow someone
access to your home, but you do not want to give them your master code.
For example, auxiliary codes can be given to houseguests, housekeepers,
housesitters, etc.
1. Press OPTIONS until the display window shows AUXILIARY
CODE, ENTER MASTER CODE.
2. Enter the master user code.
3. The display window will show ENTER 1-6. (You have six...

14
7. You will receive a confirmation beep from the keypad.
8. You may verify that the code was deleted by turning the system on
and trying to turn it off with the code you deleted. If it was deleted,
it will not turn the system off.
VIEWING ALARM MEMORY
1. Press OPTIONS until the display window shows ALARM MEMORY,
ENTER CODE.
2. Enter a valid user code.
3. The zone number of any alarms in memory will scroll through the
display window. (Refer to the pop-up zone card located at the top
of the keypad.)
4....

15
TESTING THE DOOR AND WINDOW SENSORS
You can test the door and window sensors without sending alarm signals
to the Brink’s Monitoring Center.
1. Close all protected doors and windows.
2. Check the display window on the keypad. Display window should
show READY. (If NOT READY is displayed, check the
flashing zone number to ensure it is secure. If you cannot get
the READY indication, call Brink’s Customer Service.)
3. Press OPTIONS until the display window shows DOOR CHIME.
4. Enter a valid user code to...

16
3. Press OPTIONS until the display window shows DOOR CHIME.
4. Enter the three-digit code 247 and hold the “7” key down for five
seconds. The display window will show READY DOOR
CHIME TEST.
5. Walk through the protected area. If your motion is detected, the
siren will give a short blast. (If your motion was not detected, call
Brink’s Customer Service. A service call may need to be scheduled
to adjust the motion detector.)
6. When you are finished testing the motion detector, exit the DOOR
CHIME TEST...

17
is still plugged into the electrical source. (See page 4 for description
of transformer.)
5. If the transformer is plugged in, check your electrical breaker box
to confirm that all the breakers are in the ON position.
6. If the breakers are all in the ON position, unplug the transformer.
(May require removing the retainer screw from the outlet cover.)
Plug in a small appliance to determine if the electrical outlet is
working properly.
7. If the outlet is not working, call your electrician to repair...

18
TROUBLE ON FIRE ZONE INDICATION
1. If you accidentally trip the smoke/heat detector, cancel the alarm
by entering a valid user code immediately followed by CANCEL. I f
there is still smoke, dust, steam, etc. in the smoke/heat detector,
the display window will show the zone number and TROUBLE.
2. The keypad will beep every fifteen seconds. You may silence the
beeping for 24 hours by pressing CANCEL.
3. The system will automatically try to reset when a valid user code
is entered. If it fails to reset,...

19
COMMUNICATION PROBLEM INDICATION
IMPORTANT NOTICE: Converting your phone to a DSL (Digital Subscriber Line) service or
other high speed data line could affect the ability of the Brink’s Home Security system to
transmit alarm signals. If you have switched to DSL or other high speed line service, you
should immediately test the Brink’s system’s transmission capability by following the directions
in this manual. If the transmission is not successful, call Brink’s Customer Care at
1-800-445-0872. It may...

20
CLEANING THE SMOKE DETECTOR
(OPTIONAL FEATURE)
If you had a smoke/heat detector installed, you will need to clean it every
three months. It may also be necessary to clean it after it has been tripped
by smoke or dust. To clean the smoke detector, vacuum the smoke detector
vents using a crevice attachment without removing the cover. Should this
cleaning process trip a smoke/heat detector alarm, perform the following
steps:
1. The siren will sound. Cancel the alarm by entering a valid user
code...