Addonics Technologies Storage Tower ST95HPMXA user guide

Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v5.1.11
www.addonics.com
T E C H N O L O G I E S
User Guide
Storage Tower  IX(ST95HPMXA)         

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Removing Cover of Storage 
Tower IX
Loosen the 5 screws at the back of the 
tower using a Philips screwdriver by 
turning counter-clockwise. Separate the 
metal casing of the tower from the housing 
by lifting up the casing.
Installing drives into the 
Storage Tower 
Step 1
Screw the hard drives into the optional 
mounting brackets or slide in 5.25” devices 
into the tower. Other...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Dip Switch Settings
Enable
ERR Buzzer
FunctionAuto-
Rebuilding
to Spare
Drive Port Multiplier Mode
Raid Mode
1               2     3                4               5
Individual Drive(Factory Default)OFF
OFF
OFF
OFF
OFF
OFF
OFFOFF
ON
ON
ON
OFF
OFF ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF OFF
ON
ON
OFF ON
ON
OFF OFF
ON
OFF
OFF
OFF ON
ON
0
1 and 10
3
5
Clone
Large
RAID Setting Button
Dip Switch...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Default factory DIP Switch setting:
SW1 – RAID Setting DIP Switch
BZS –   Error buzzer function
EZ   –   Automatic rebuilding to spare drive (one of the drives on the raid is s\
et as a  
  spare). If EZ is ENABLED anda drive failure occurs, the spare will    
  automatically act as a drive replacement and rebuilding will automatical\
ly  
 start.
M2  –   RAID mode 2
M1  –   RAID...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Setting or Modifying the RAID Mode Using the JMicron 
HW RAID Manager Utility Program:
1.  For Windows users, install the JMicron HW RAID Manager located on the  
  SATA Controller CD. In the CD, go to Configuration Utilities > JMB393. This  
  manager can be use to create and monitor the status of the RAID volume.
  It is recommended to use the default factory RAID DIP switch...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
    e.  On the DIP switch, change (M0 to M2) setting to the  
      desired RAID mode using the diagram below.
      All settings on the diagram shows
      •  Error buzzer function is ENABLED
      •  EZ function is DISABLED.
1      2      3      4      5SW1
BZS  EZ    M2   M1   M0
RAID 0 Mode
1      2      3      4      5SW1
BZS  EZ    M2   M1   M0
Clone Mode
1      2      3      4...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
  f.  Press the RAID setting button with a ball point pen.
  g.  While pressing the RAID setting button turn on the system power  
    where the HPM is connected. The buzzer will sound while holding the  
    RAID setting button. Release it after at least 5 seconds for hardware  
    initialization. A single beep will be heard to indicate initialization is  
  completed. 
  h....

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
  f.  Press the RAID setting button with a ball point pen.
  g.  While pressing the RAID setting button turn on the system power  
    where the HPM is connected. The buzzer will sound while holding the  
    RAID setting button. Release it after at least 5 seconds for hardware  
    initialization. A single beep will be heard to indicate initialization is  
  completed. 
  h....