Addonics Technologies Duplicator Subsystem DDU11SAS user guide web

							Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v8.1.11
T E C H N O L O G I E S
www.addonics.com
User Guide
1:11 Blu-Ray / DVD Duplicator
(DDU11SAS)         
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Diagram
10 Destination 
ODD Ports
LCD Console Display
EN T
E SC
Dupl ic a to r P anel
LC D
S crol l  U p
S crol l  D ow n
E
xe cu te s F unctio n
C ance ls  F unctio n
15-pin SATA power connector 
Source ODD Port
HDD Port for
image burning 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Quick Guide
Installing the 1:11 optical duplicator
Step 1
Insert the 1:11 Blu-Ray / DVD Duplicator into standard 5.25” drive ba y.
Step 2
Connect the power cable from your  system to the SATA power connector.
Step 3
Connect  the  source  drive to the  source  SATA port  via SATA  cable  and  the target 
drives to the destination S ATA  port via SATA  cable.
 
Step 4
Screw the duplicator into the drive bay with 4 screws (2 on each side)\
.
Duplicating drive(s) 
Make  sure the source  and target  drives  are connected  to the  proper  ports.  
When the duplicator is on, it will go through the steps belo w.
Step 1
Duplicator LED will light up and the device will beep.
Step 2
LCD will display initial steps:
  1.  Duplicator V er: - Displays duplicator version
  2.  Initializing SDRAM  
  3.  Detect Source/T arget - Will detect the type of source/targets 
  4.  Copy - Defaults to the first function which is to copy
Step 3
Once  the duplicator  gets  to the  copy  menu,  press ENT to  begin  copying.   The 
duplicator  will  auto-detect  the drive  and display  its  information  on  the  LCD.   Make 
sure  that the power  LEDs  of the  flash  reader  are  blinking,  the  blinking  indicates 
drive activity .
Y ou  can  find the complete  user  manual  of  the  1:11  Blu-Ray  /  DVD  Duplicator  panel 
on  the  driver  disk under  user  guides.   Y ou  can  also  download  it  from  our website  at 
www .addonics.com/support/user_guides/
  
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Pan el Functions
E N T
ESC
Duplic ator P anel
LCD
Scroll  Up
Scroll  Down
Execut
es Function
Canc els Function
The D uplicato r h as  6 f unctions  t o  choose  from:
1 . Copy
2 . T est
3 . T est & Copy
4 . V erif y
5 . Compare
6 . Prescan
7 . Disc I nfo
8 . Select Source
9 . Image
10. Edit  T rack
1 1 . Light scribe
12. Se tu p
7.1  S ource
7 .2  T arget9 .1  Load
9 .2  Delet e Image
9 .3  Image I nfo
9 .4  Compare I mage
9 .5  S elect Image
9 .6  Image S rc Drvie
9 .7  ImageF ormat In fo
9 .8  E dit
9 .9  F ormat  HDD
9 .10  LoadI mage  Method
10. 1 CD t o CD E dit
10. 2 CD t o HDD E dit
10. 3 Close S ession
11 .1  P rint
1 1 .2  Load  LSI to  HDD
1 1 .3  S elect  LSI File
1 1 .4  Delet e L SI File
1 1 .5  Load  LSI  Drive
1 1 .6  Coypright In fo
12. 1 Language
12. 2 B urn S peed
12. 3 Read S peed
12. 4 A uto  Start  Drive
12. 5 Start up Menu
12. 6 A uto  V erif y
12. 7 A uto  Compare
12. 8 A uto  P rescan
12. 9 E ject  Disc 12.
10 B urn O n T he F ly
12. 11  B urn  Mode
12. 12 Display  Time
12. 13 B utton S ound
12. 14 Device I nfo
12. 15 S ystem I nfo
12. 16 Q uick E rase
12. 17 F ull Erase
12. 18 Auto  Close  Tray 12.
19 Q uick Compare
12. 20 Link  Mode S elect
12. 21 Re-S can
12. 22 Tray-I n/Ou t
12. 23 B ootTime  Delay
12. 24 Start  T ray E ject
12. 25 Disc  Redet ect
12. 26 S how B urn Speed 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
1. CopyFunction#1 Copy , instant  copy source  (disc/image)  to  the  target  drives  (optical  writes).  Use Function#8 
to  select  source  drive before  copying.  Select  function#1.  place  a  source  disc into source  drive and blank 
disc  into the target  drives.  A rewriteable  disc  can be used  as target  media,  however  all  data  will be 
erased before copying.
Press  ENT to  start  copy  function  when all  discs  are ready .  After  complete,  system will show  spent  time 
and the amount of OK disc on the screen, the OK disc will be ejected.
2. T estFunction#2,  copy  simulation,  no  data  will be  written  to the  write  once  media  (DVD+R  is not  supported 
for this function).
Press  ENT to  start  simulation.  If  rewriteable  disc  is used,  all contained  data  will be  erased  before 
simulation.
3. T est & CopyFunction#3,  will  do  copy  simulation  before  copy function.  Press  ENT to  start  simulation  and  copy.  
Note, only passed test disc will do the cop y.
4. V erifyFunction#4, check readability of the burned disc.
5. CompareFunction#5, to check if target disc is identical to source disc.
Compare result :
OK: Source and target disc are identical
Fail: T OC not match, compare skipped due to contains do not match.
Dif f: Shows how many bytes are di fferent.
6. PrescanFunction#6, to check if source disc is readable and without read erro r.
7. Disc InfoFunction#7, to report disc information, disc type and capacit y.
8. Select SourceFunction#8,  to  set  which  drive  as source  device.  The drive  on CH01  will  be  chosen  as  source  device. 
Press ENT , and then press ▲ ▼ to select the source.
Assume  that HDD  is selected  as  the  source  device and  selected  partition  contains  no  data,  an error 
message  “Source  Drive Not Ready”  will  show  on LCD  while trying  copy function.  In that  case,  go to 
Function#9 Image to load the data into the chosen partition first. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
9. Image
Function#9 Image is valid only when a hard disk is installed. Disc is lo\
aded to hard disk as an
image file.
9.1 Load
Load function loads whole disc data from any writers into the current pa\
rtition of the hard disk.
“P:A” means current partition is A.
9.2 Delete Image
If you want to delete an image file stored in a particular partition, yo\
u can use this function to
delete  image.  Press ENT ,  the  system  will confirm  with you for the  action,  use ▲ ▼ to select  Yes  or 
No, then press ENT  for confirmation.
9.3 Image Info
T o check selected image information. First, enter into the function and press ▼ for more
information.
9.4 Compare Image
This function is used to check if created image is identical to source d\
isc.
When result shows on LCD, press EN T for more detail information.
Compare result :
OK: Source and target disc are identical
Fail: T OC not match, compare skipped due to contains not match.
Dif f: shows how many bytes are di fferent.
9.5 Select Image
This  function  is to  select  a partition  as  source  image from  the hard  disk.  Pressing  ▲  ▼ to select  a 
partition, LCD will show image name and capacit y.
9.6 Image Src Drive
This function is used to set the image source drive for loading disc dat\
a into a particular partition.
Enter into the function and use ▲ ▼ to select image source drive.
9.7 ImageFormat Info
This function shows which format is used for current hard disk. It is re\
lated to function#12.4 Format
HDD.  
9.8 Edit
This function is to edit selected images title, sub1 title and sub2 tit\
le. Only valid when the current
partition  contains  an  image  file  can  title.   A  title  should  be  composed  of  1 to  13  characters.  The 
character  can be alphabet,  number  or  the  combination  of  both.  Use ▲ ▼ to select  the number  or 
alphabet.  After  selecting  a  desired  one,  press  ENT for  next  character , the  end  of key  in, press  and 
hold EN T for 2 sec and release for next title. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
9.9 Format HDD
Hard disk must be formatted by the system for the very first time. Hard \
disk will be partitioned into
the chosen partition format.  If no hard disk is installed, LCD will sho\
w the message as No  Valid HDD!
All  data  on the  hard  drive  will be  erased  after  the hard  disk format.  After the hard  drive  is formatted 
correctly , LCD  will show  “ Format  HDD ok!.”,  Press  ENT to  verify  HDD or press  ▼ and  choose  No  return 
back to menu.
9.10 LoadImage Method
This  function  is to  change  the  way  to save  Image.  There are 2 formats  for choice:  Auto and Manual. 
Auto  means  system  auto assign  partition  for  loaded  image.  Manual  let  you  to choose  which  partition  to 
load image to.
10 Edit T rack (for  Audio CD only)Function#10  Edit  Track  is exclusively  designed  for  editing  a  collection  of  favorite  songs from CDs.  In 
other  words,  you can collect  songs on a number  of  CDs  and merge  them into a single  CD.  There  are 3 
sub-functions: CD to CD, CD to HDD and Close Session.
10.1 CD to CD Edit
T o select songs from source CD, and then burn into a blank CD-R/ RWs. 
Y ou  can  press  ▼ to see  the rest  of tracks.  If you  want  to select  the track,  press  ENT then  a “+”  will 
shows  up, press  ENT again  will  cancel  the  selection.  After  selection,  use  ▲▼  move  to the  “End”  which 
is between 1st track and last track. Press ENT  to end of selection, and use ▲ ▼ to confirm Yes or No. 
Press  ENT after  burning,  system  will ask  if you  want  to continue  edit,  use ▲ ▼ to confirm  Yes  or No.  If 
you  want  to continue  edit,  the current  source CD will be  ejected
 and  ask you  to insert  next disc.  Repeat 
the above process for editing.
After editing, system will show Close all discs session ?  Y es”, use ▲ ▼ to confirm  Y es or No.
Once session is closed, no more tracks can be added.
Attention:
Commercial audio player might not able to play open session disc, close \
session is suggested for
max. compatibilit y.
10.2 CD to HDD Edit
T o select tracks from single or multi-audio CD and create image to specif\
ic partition of HDD
The basic operation method is same as CD to CD Edit, system still ask yo\
u to insert empty disc
even the target drive is HDD. If burning successful, system will show \
Image load OK, which
means the selected tracks are written to temporary partition.
Press ENT  after burning, system will ask if you want to continue edit, use ▲ ▼ to confirm  Yes or No.
If you want to continue edit, the current source CD will be ejected and \
ask you to insert next disc.
Repeat  the  above  process  for editing.  If  No  is selected,  system will show  Burn  or Move  to partition 
?'', use ▲ ▼ to confirm Burn or Move.
Burn : Burn the selected tracks to CD
Move to partition : Create an image for selected tracks. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10.3 Close Session
Single session format is used for Audio CD, and commercial audio player is not able to play open
session audio CD, therefor session must be closed to max. playback compa\
tibilit y. However , no
more tracks can be added once session is closed.
1 1 LightScribe (Optional Function)LightScribe is an optical disc recording technology that uses specially \
coated recordable CD and
DVD media to produce laser-etched labels with text or graphics, as oppos\
ed to stick-on labels and
printable discs.  This function includes 6 sub-functions: Print, Load LSI to HDD, Select L\
SI File,
Delete LSI File, Load LSI Drive and Coypright Info.
1 1.1 Print
Use optical drives laser to print loaded LSI file. Disc should placed u\
p side down.
1 1.2 Load LSI to HDD
Load LSI to hard disk.
1 1.3 Select LSI File
Select LSI file from hard disk for laser printing.
1 1.4 Delete LSI File
Delete a LSI File stored in a particular partition. Use ▲ ▼ to confirm  Yes or No.
1 1.5 Load LSI Drive
This function is to select source drive in order to load LSI File into a\
 particular partition.
1 1.6 Coypright Info
This function is to see the LightScribe copyright information.
12 SetupT o change the default setting. Howeve r, it is suggested to use the default for the optimal operation.
There are 24 sub-functions: Language, Burn Speed, Read Speed,  Auto Start Drive, Startup Menu,
Auto V erify, Auto Compare,  Auto Prescan, Eject Disc, Burn On  The Fly, Burn Mode, Display  T ime,
Button Sound, Device Info, System Info, Quick Erase, Full Erase,  Auto Close T ray , Quick
Compare,  T ray-In/Out, BootT ime Delay, Start  T ray Eject, Disc Redetect and Show Burn Speed.
12.1 Lanuage
Now press EN T, and you will enter the following figure.  The function Language lets you select a
language in which messages can be shown on LCD.
12.2 Burn Speed
Now press ESC and ▼ to enter the following figure.  This function lets you control the burning
speed  of  CD  writers.  DVD Burn  Speed  is  defaulted  to  16X,  BD Burn  Speed  default  is 4X,  CD Burn 
Speed default is 32X and  Audio Burn Speed is is defaulted to 16X.
12.3 Read Speed
T o  change  default  reading  speed  of  source  disc. The default  is Of f. Press  ▼ to select  1 or  2 (blank 
disc).
12.4  Auto Start Drive
System will auto start to copy or test once blank disc is read y.
12.5 Start Up Menu 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
To select any function from #1 to # 13 as the first item appears on the s\
creen whenever system is
turned on.
12.6  Auto V erify
T o set if auto verify target discs readability after copy function.  The default is Of f. Press ▼ to select On.
12.7  Auto Compare
T o set if auto do comparison after copy function to check if source and t\
arget disc are identical.
The default is Of f. Press ▼ to select On.
12.8  Auto Prescan
T o set if auto scan source disc before copy function.  The default is Of f. Press ▼ to select On.
12.9 Eject Disc
There are 3 kinds of tray behavior when copy process is completed.
Eject Good Only: Only good disc will be ejected after burning.
Eject  All Disc :  All discs will be ejected after burning.
Do Not Eject :  All discs stay in after burning.
The default is Eject Good Only .
12.10 Burn On  The Fly
Burn On  The Fly means data will be copied directly from the source disc to the t\
arget disc. When
the setting is Of f, the data will be loaded into temporary partition of HDD first, then c\
opy from HDD
to disc.  The default is On. Press ▼ to select O ff.
12.1 1 Burn Mode
There  are two  modes:  DAO (Disc  At Once)  and TAO  (Track  At Once).  The default  is DAO.  Press  ▼ to 
select  TAO.
12.12 Display  T ime
T o set if display a timer while copying.  The default is On. Press ▼ to select O ff.
12.13 Button Sound
T o enable or disable beep sound while press a ke y.
12.14 Device Info
T o show the writer information.
12.15 System Info
T o show system Information.
12.16 Quick Erase
T o erase data on the DVD rewriteable discs quickl y.
12.17 Full Erase
T o erase data on the DVD rewriteable discs completel y. Compared with Quick Erase, Full Erase
takes longer time to do the job.
12.18  Auto Close  T ray
All tray will be closed in selected time and if disc is read y, system will auto start copy , test or both
functions, depends on which function is stay on the LCD screen.
The default is Of f, press ▼ to select 1 Byte, 1 KB, 10 KB, 100KB, 1 MB, 10MB, 100MB etc. 
						

							www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
12.19 Quick Compare
Quick Compare is related to function#5 Compare. Once compare error byte \
reach to the setting
figures, compare process will stop.
12.20 Link Mode Select (Select Models)
Now press  ESC and ▼ to enter  the following  screen.  Press  ENT to  enter  the “Link  Mode  Select” 
screen.  Use ▲ ▼ to choose  between  the  Stand  Alone,  Middle T ower  or Last  Tower  modes  as 
appropriate.
Attention:  Once a tower  has been  set  as Middle  T ower  or Last  Tower  and the J14  jumper  is  also  set 
to  Target mode, the LCD will show that it is in  T arget mode.
12.21 Re-Scan (Select Models)
Now  press  ESC and ▼ to enter  the following  screen.  Press ENT to  enter  the “Re-Scan”  screen.  By 
default  this is set  to No.  Use  ▲ ▼ to choose  Y es  then  press  ENT to  scan  the chosen  connected 
tower .
12.22  Tray-In/Out
Lets  you control  the drive  tray ejecting.  The  default  is All  Once  and there  have Divide  2  Times  for 
selection.  The default is 5 second, more option is up to 99 seconds.
12.23 BootT ime Delay
T o set the device scanning time during the system booting.
12.24 Start  Tray Eject
T o set if do eject all tray after system boot up.  The default is On. Press ▼ to select Off.
12.25 Disc Redetect
The function is designed specially for bad quality disc, the system will\
 detect the disc one more
time if disc recognition error occurred.  The default is Of f. Press ▼ to select On.
12.26 Show Burn Speed
Now press ESC and ▼ to enter the following figure.  This function lets LCD shows the burning
speed of CD/DVD/BD writers.  The default is On. Press ▼ to select O ff.