ADDERLink X100 Manual Rx

welcome
contents
installation
 
& operation
special
 
configuration
furter
information
0
Hot plugging and mouse restoration
It is strongly recommended that you switch off the computer system before 
attempting to connect the local device and X100 receiver. However, if this is not 
possible then you need to ‘hot plug’ the local device and X100 receiver while 
power is still applied to the system. There is not normally a danger of damage 
to the system, however, when mouse communications are...

welcome
contents
installation
 
& operation
special
 
configuration
furter
information

To	apply	remote	user	video	compensation
1  On the keyboard that is connected to the X100 receiver, simultaneously, 
press the hotkeys (by default,  and ) along with  to enter 
configuration mode.
The three keyboard indicators (‘Num Lock’, ‘Caps 
Lock’ and ‘Scroll Lock’) will now begin to flash in 
sequence. The speed of the sequence indicates the 
level of the sharpness adjustment currently applied: 
the...

welcome
contents
installation
 
& operation
special
 
configuration
furter
information

Skew adjustment
The category 5, 5e and 6 cabling supported by the X100 receiver consists of four 
pairs of wires per cable. Three of these pairs are used to convey red, green and 
blue video signals to the remote video monitor.  due to the slight difference in 
twist rate between these three pairs, the 
red, green and blue video signals may not 
arrive at precisely the same time. This is 
visible as...

welcome
contents
installation
 
& operation
special
 
configuration
furter
information

3  As appropriate, press either the R, G or B keyboard keys to 
select the appropriate colour channel. Corresponding 
keyboard indicators will flash rapidly to show which 
channel is currently selected for adjustment: 
Num Lock for Red, Caps Lock for Green and 
Scroll Lock for Blue.
Advance	
colour	
timing
Retard	
colour	
timing
Restore
default	
skew
settings	
Exit	image	
controls	
and	save	
settings...

welcome
contents
installation
 
& operation
special
 
configuration
furter
information

Performing flash upgrades
The Adder X100 receiver is fully reconfigurable via flash upgrades using the 
kVM Firmware Uploader utility
. 
during the upgrade you will be required to connect the X100 receiver directly 
to a computer system using a special cable. The upgrade utility will upd\
ate the 
firmware of the X100 receiver and also temporarily transform it so that it can 
update the CAM unit. Once...

welcome
contents
installation
 
& operation
special
 
configuration
furter
 
information
5
Further information
Getting assistance
•  Adder.Technology.website – www.adder.com
  Check the Support section of our website for the latest solutions and dr\
iver 
files.
• 
Email – [email protected]
• 
Fax   in the Uk:  05	00
    in the US:  +		5	
• 
Phone  in the Uk:  05	00
    in the...

welcome
contents
installation
 
& operation
special
 
configuration
furter
 
information
6
Warranty
Adder Technology Ltd warrants that this product shall be free from defects in 
workmanship and materials for a period of two years from the date of original 
purchase. If the product should fail to operate correctly in normal use during the 
warranty period, Adder will replace or repair it free of charge. No liability can be 
accepted for damage due to misuse or circumstances outside Adder’s...

welcome
contents
installation
 
& operation
special
 
configuration
furter
 
information

Radio Frequency Energy
A Category 5 (or better) twisted pair cable must be used to connect th\
e units in 
order to maintain compliance with radio frequency energy emission regulations 
and ensure a suitably high level of immunity to electromagnetic disturbances.
All other interface cables used with this equipment must be shielded in \
order 
to maintain compliance with radio frequency energy emission...

welcome
contents
installation
 
& operation
special
 
configuration
furter
 
information

© 2006 Adder Technology Limited
All trademarks are acknowledged.
Release 1.0b
december 2006
Part No. Add0068
Adder Technology Limited,
Technology House,
Trafalgar Way, Bar Hill,
Cambridge, CB3 8SQ,
United kingdom
Tel: +44 (0)1954 780044
Fax: +44 (0)1954 780081
Adder Corporation,
29 Water Street,
Newburyport,
MA 01950,
United States of America
Tel: +1-888-932-3337
Fax: +1-888-275-1117
 
www.ctxd.com...