ADDERLink INFINITY dual Manual v30

							50
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
VESA bracket mount
This optional kit comprises a bracket that allows a single AdderLink 
Infinity module to be mounted onto the rear of a video display*.   
The kit includes the bracket plus eight screws.  
* The video display must adhere to the VESA standard for mounting holes 
on its rear panel.    
						

							51
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
WARRANTY
Adder Technology Ltd warrants that this product shall be free from defects in 
workmanship and materials for a period of two years from the date of original purchase. 
If the product should fail to operate correctly in normal use during the warranty period, 
Adder will replace or repair it free of charge. No liability can be accepted for damage due 
to misuse or circumstances outside Adder’s control. Also Adder will not be responsible 
for any loss, damage or injury arising directly or indirectly from the use of this product. 
Adder’s total liability under the terms of this warranty shall in all circumstances be 
limited to the replacement value of this product.
If any difficulty is experienced in the installation or use of this product that you are 
unable to resolve, please contact your supplier.
SAFETY INFORMATION
• For use in dry, oil free indoor environments only.
• Warning - live parts contained within power adapter.
• No user serviceable parts within power adapter - do not dismantle.
• Plug the power adapter into a socket outlet close to the module that it is powering.
• Replace the power adapter with a manufacturer approved type only. 
• Do not use the power adapter if the power adapter case becomes damaged, cracked 
or broken or if you suspect that it is not operating properly.
• If you use a power extension cord with the units, make sure the total ampere rating of 
the devices plugged into the extension cord does not exceed the cord’s ampere rating. 
Also, make sure that the total ampere rating of all the devices plugged into the wall 
outlet does not exceed the wall outlet’s ampere rating.
• Do not attempt to service the units yourself.   
						

							52
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
RADIO FREQUENCY ENERGY
A Category 5 (or better) twisted pair cable must be used to connect the units in order 
to maintain compliance with radio frequency energy emission regulations and ensure a 
suitably high level of immunity to electromagnetic disturbances.
All other interface cables used with this equipment must be shielded in order to maintain 
compliance with radio frequency energy emission regulations and ensure a suitably high 
level of immunity to electromagnetic disturbances.
European EMC directive 2004/108/EC
This equipment has been tested and found to comply with the limits for a class A 
computing device in accordance with the specifications in the European standard 
EN55022. These limits are designed to provide reasonable protection against harmful 
interference. This equipment generates, uses and can radiate radio frequency energy 
and if not installed and used in accordance with the instructions may cause harmful 
interference to radio or television reception. However, there is no guarantee that 
harmful interference will not occur in a particular installation. If this equipment does 
cause interference to radio or television reception, which can be determined by turning 
the equipment on and off, the user is encouraged to correct the interference with one 
or more of the following measures: (a) Reorient or relocate the receiving antenna. 
(b) Increase the separation between the equipment and the receiver. (c) Connect 
the equipment to an outlet on a circuit different from that to which the receiver is 
connected. (d) Consult the supplier or an experienced radio/TV technician for help. 
FCC Compliance Statement (United States)
This equipment generates, uses and can radiate radio frequency energy and if not 
installed and used properly, that is, in strict accordance with the manufacturer’s 
instructions, may cause interference to radio communication. It has been tested and 
found to comply with the limits for a class A computing device in accordance with 
the specifications in Subpart J of part 15 of FCC rules, which are designed to provide 
reasonable protection against such interference when the equipment is operated in a 
commercial environment. Operation of this equipment in a residential area may cause 
interference, in which case the user at his own expense will be required to take whatever 
measures may be necessary to correct the interference. Changes or modifications not 
expressly approved by the manufacturer could void the user’s authority to operate the 
equipment.
Canadian Department of Communications RFI statement
This equipment does not exceed the class A limits for radio noise emissions from digital 
apparatus set out in the radio interference regulations of the Canadian Department of 
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites 
applicables aux appareils numériques de la classe A prescrites dans le règlement sur le 
brouillage radioélectriques publié par le ministère des Communications du Canada.   
						

							53
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
www.ctxd.com Documentation by:
© 2015 Adder Technology Limited
All trademarks are acknowledged.
Part No. MAN-ALIF2000-ADDER • Release 3.4
Web:  www.adder.com
Contact:  www.adder.com/contact-details
Support: forum.adder.com   
						

							54
INSTALLATION
CONFIGURATION
OPERATION
FURTHERINFORMATION
INDEX
HT
A
Active Copper  14
Adaptive  45
AFZ  3,26
Anti-dither support  3
B
Bracket
rack mount  48,49
Browser-based utility  20
C
Cable
null-modem  46
Cloning displays  33
CODEC  3
Compression  26
Configuration
browser-based utility  20
switches  21
Connections
network link  14
overview  10
RX audio  17
RX AUX port  18
RX power in  18
RX USB devices  17
RX video display  16
TX audio links  12
TX AUX port  13
TX power in  13
TX USB link  12
TX video link  11
Connectors
overview  5,6
Cut-through  45
D
Dimensions  46
Display cloning  33
Dithering  3
F
Factory reset  19
Fast-Leave  43
Fibre Channel  14
Firmware
upgrade  21
Forwarding modes  45
Fragment-free  45
Frame Skipping  26
Front panel  5,6
Front panel indicators  22
G
Gigabit Ethernet  14
I
IGMP  43
fast-leave  43
querier  43
snooping  43
Indicators  5,6,22
Initial configuration  19
J
Jumbo frames (packets)  43
L
Layers 2 and 3  45
Link cable lengths  14
M
Magic Eye  3,26
Management port  6,25,32
RX settings  32
TX settings  25
Multicast settings  33
N
Network layout  39
Network switch
choosing  39
Null-modem cable
pin-out  46
O
Optimization
statistics for  29,37
Options switches  21
OSI model  45
Q
Querier  43
R
Rack mounting  48
Rear panel  5,6
Reset
manual  19
S
Safety information  51
SFP module  14
Snooping  43
Spanning Tree Protocol  44
Specifications  46
Statistics
graphing  29,37
Store and forward  45
Switch
choosing  39
configuring  40
System port  5,6,14,25,32
RX settings  32
TX settings  25
T
Teaming port  5,6,14,25,32
RX settings  32
TX settings  25
TLS  3
Transport Layer Security  3
Troubleshooting  41
U
Upgrade
firmware  21
V
Video modes  46
W
Warranty  51
Weight  46
Index