Adder RED PSU Manual

10
INSTALLATION
conFiGuRation
OPERATION
FURTHER
INFORMATION
INDEX
the GeneRal conFiGuRation P
aGe
This page contains various important settings related to RED-PSU 
labelling, login, identity and startup.
imPoR tant: When you make a change to any setting, don’t 
forget to click the update button to save the change.
Note: The Name, Description and Location fields accept ASCII characters only. 
UTF-8 characters are not supported.
•  Name - the primary identity of this RED-PSU unit.
•  Description - a...

11
INSTALLATION
conFiGuRation
OPERATION
FURTHER
INFORMATION
INDEX
the netW
oRK SettinGS P aGe
This determines the network settings used by the RED-PSU unit.
imPoR tant: When you make a change to any setting, 
don’t forget to click the update button to save the 
change.
•  Obtain IP Address automatically - when ticked, the RED-PSU 
will use DHCP (Dynamic Host Configuration Protocol) to 
automatically determine all network settings (and all other 
options in this page will be grayed out). When unticked,...

12
INSTALLATION
conFiGuRation
OPERATION
FURTHER
INFORMATION
INDEX
the uSeR 
accountS P aGe
This page allows you to administer the details for users of the RED-PSU 
unit. By its nature RED-PSU is not an end user access product, so every 
authorized user is considered as an admin with the same rights. Extra 
users can be added and deleted, however, the main ‘admin’ entry cannot 
be deleted or renamed, only its password can be changed. 
Note: The RED-PSU will only request Login details if the ‘Login...

13
INSTALLATION
conFiGuRation
OPERATION
FURTHER
INFORMATION
INDEX
the Sy
Stem oPeRationS P aGe
This page contains various options for resetting and updating the RED-
PSU. All options given here will interrupt normal operations and should 
be used with caution.
Device  reset
This option will reset the operation of the RED-PSU unit, equivalent to a 
cold reboot (as if power to it had been removed and restored). All power 
outputs will be removed and then restored in a staggered manner defined 
by the start...

14
INSTALLATION
CONFIGURATION
oPeRation
FURTHER
INFORMATION
INDEX
Operation
inDicatoRS
The RED-PSU main chassis contains various indicators to provide you with status 
information. There are four main indicators on the front panel as well as green and 
amber indicators on the network port connector.
Red status indicators
The red status indicators on the front panel provide various key power and operation 
feedback:
P1
On:  The power 
module in bay 1 has 
a mains input and is 
operating.
Flashing:  An...

15
INSTALLATION
CONFIGURATION
oPeRation
FURTHER
INFORMATION
INDEX
ReStoRinG Po
WeR outPutS
As discussed in the Welcome section, the RED-PSU ports are carefully monitored to 
ensure safety protection while also maintaining power consistency to the multiple 
devices:
•  Electronic short protection - If an overload or short circuit occurs on any output, 
the power is limited to a safe value (by current pulsing) until the microprocessor 
recognises the overload condition and trips the output – this happens...

16
INSTALLATION
CONFIGURATION
OPERATION
FuR
theR
inFoRmation
INDEX
This chapter contains a variety of information, including the following:
•  Getting assistance - see right
•  Safety information
•  Warranty
•  Radio frequency energy statementsGettinG aSSiStance
If you are still experiencing problems after checking the information contained within this 
guide, then we provide a number of other solutions:
• online solutions and updates  – www.adder.com/support
  
 Check the Support section of the...

17
INSTALLATION
CONFIGURATION
OPERATION
FuR
theR
inFoRmation
INDEX
WaRRanty
Adder Technology Ltd warrants that this product shall be free from defects in 
workmanship and materials for a period of two years from the date of original purchase. 
If the product should fail to operate correctly in normal use during the warranty period, 
Adder will replace or repair it free of charge. No liability can be accepted for damage due 
to misuse or circumstances outside Adder’s control. Also Adder will not be...

18
INSTALLATION
CONFIGURATION
OPERATION
FuR
theR
inFoRmation
INDEX
RaDio FRequency eneRGy
A Category 5e (or better) twisted pair network cable must be used to connect the units 
in order to maintain compliance with radio frequency energy emission regulations and 
ensure a suitably high level of immunity to electromagnetic disturbances.
european emc directive 2004/108/ec
This equipment has been tested and found to comply with the limits for a class A 
computing device in accordance with the specifications...

19
INSTALLATION
CONFIGURATION
OPERATION
FuR
theR
inFoRmation
INDEX
www.ctxd.com Documentation by:
© 2015 Adder Technology Limited
All trademarks are acknowledged.
Part No. MAN-PSU-RED-ADDER • Release 1.0a
Web:   www.adder.com
Contact:   www.adder.com/contact-details
Support:  www.adder.com/support