ADDER ePower Switch 8 Master Manual

eP
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Version 0
9
             
 
Pow
9/2009 
                    
werS
                   
Swi
Us
                   
 
tch
 
 
ser gu
                    
 8X
uide
                   
M 
R
                   
R2
 
             wwww.neol.com 
  

1 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
© Copyright by NEOL S.A.S - 4 Rue Nationale, 67800 BISCHHEIM, France 
 
Printed in France 
 
All rights reserved. No part of this documentation, accompanying software or other components of the 
described product may be reproduced or transmitted in any form or by any means, electronic or mechanical, 
including photocopying and recording, for any purpose other than the personal use of the purchaser without 
the express written permission of NEOL S.A.S....

 
2  
 
 
 
 
 
CONTENTS 
 
 
 
 
 
 
SAFETY INSTRUCTIONS: To be read before use! ...................................................................................... 3
 
1. DESCRIPTION .......................................................................................................................................... 4 
1.1 Diagram ............................................................................................................................................... 4 
1.2 Package list...

3 
SAFETY INSTRUCTIONS: To be read before use! 
 
  
NOTE 
 
• The ePowerSwitch devices can only be installed by qualified people with the following installation and 
use instructions. The manufacturer disclaims all responsibility in case of a bad utilization of the 
ePowerSwitch devices and particularly any use with equipments that may cause personal injury or 
material damage. 
• This equipment is designed to be installed on a dedicated circuit that must have a circuit breaker or fuse 
protection.  
•...

 
4
1. DESCRIPTION 
 
ePowerSwitch*8XM is a power control unit with a built-in Web server, an Ethernet and a RS232 
connection. It enables to control the power supply of 8 power outlets through an Ethernet connection. The 
number of controlled power outlets can be extended up to 136 by cascading up to 16 ePowerSwitch 8XS 
to the Master. It supports a maximum load of 2x10A through 2 separate power inputs. 
 
This high security unit offers HTTPS protocol with Web browsers that support SSL version 2 or 3....

5 100 (LED) 
Off = 10 Mbits/sec connection 
On = 100 Mbits/sec connection 
RS232 (SUB-D 9F Connector) 
Serial port RS232 with DB-9 female connector 
Pinout 
2 = TxD 
3 = RxD 
5 = Gnd 
 
xBus 
The RJ45 connector is used for cascading ePowerSwitch devices and xBus peripherals 
Maximal TOTAL line length: 200 meters 
 
Term (RS485 Termination DIP Switch) 
The xBus interface (RS485) has built-in termination resistors. To enable these resistors slide the two 
DIP Switch to the ON position (down).  
Termination...

 
6 The back panel of the ePowerSwitch 8XM 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
Power input B 
230 VAC – 10 Amp 
Power outlets (Group B) 
Power outlets 5 – 8 
230 VAC max 10 Am
p 
Power outlets (Group A) 
Power outlets 1 – 4 
230 VAC max 10 Am
p 
Power input A 
230 VAC – 10 Amp  

7   
1.2 Package list 
 
The following items are included: 
 
‰  1 ePowerSwitch 8XM
R2 19  
‰  1 power adapter 12 VDC  
‰  2 power cables, 230 V / 10 Amp, length 1.80 Meters 
‰  1 RJ45 M/M cable, 2 Meters 
‰  1 serial cable SUB-D 9 points M/F, 1.80 Meters 
‰  1 quick installation guide 
‰  1 CD with User Guide, Quick Start Guide and Windows configuration program 
 
 
  

 
8
2. INSTALLATION 
 
Remark:  
Make sure that the ePowerSwitch 8XM is powered off. 
 
 
Connection instructions 
 
1.  Use a shielded
 RJ45 network cable to connect your ePowerSwitch 8XM to the network.  
 
2.  Use appropriated three-wire power cords (two poles plus ground) to connect your electrical devices to 
the ePowerSwitch 8XM unit.  
 
3.  Plug the 2 power cables into 2 grounded 
sockets. The power supply LED of group A and of group B 
light on to confirm that power is on.  
 
4.  You can now...

9 
3. CON
 
To use th
e
network ad
 
There are 
 
3.1. Con
It is the si
configure 
compatibl
e
 
1. Start t
 
2. Open 
ePow
e
 
3. Open 
config
  
This p
a
version
settings
!!! To 
Finder 
 
 
NFIGUR
e ePowerSw
dministrator f
three metho
nfiguratio
mplest and 
your ePow
e
e with those 
he Finder.e
x
the File men
erSwitch 8XM
the File men
ure the netw
age enables
n of the Firmw
s. 
achieve th
e
program af
RAT I O N  
itch 8XM on 
for the param
ods to configu
on throug
fastest confi
erSwitch 8XM
of your...