Adam Equipment CBD Bench Counting Scales CBDREVBAE2 User Manual

©
 Adam Equipment Company 2011 
Adam Equipment 
 CBD SERIES 
 (P.N. 302666242, Revision B, May 2011)    

 
© Adam Equipment Company 2011   
 
  

 
© Adam Equipment Company 2011  Page  
1 
 
    
CONTENTS 
   
1.0  INTRODUCTION ....................................... ............................................................... 3 
2.0   TECHNICAL SPECIFICATIONS ........................... .................................................... 4 
2.1   SPECIFICATIONS FOR THE LOCAL SCALE ................. ..................................... 4 
2.2   SPECIFICATIONS FOR THE REMOTE SCALE ................ ................................... 4 
2.3...

 
© Adam Equipment Company 2011  Page  
2 
 
  

 
© Adam Equipment Company 2011  Page  
3 
 
 
1.0  INTRODUCTION 
   
·  The  CBD  series  offers  a  range  of  an  accurate,  fast  and  versatile 
counting  scales  that  can  use  one  additional  externa l  platform 
(Remote scale) for weighing or counting of heavier  items.    
 
·  These  counting  scales  have  the  ability  to  use  many  stored 
information (PLU). 
 
·  The scale can be operated using either pounds only,  kilograms only 
or can be switched between pounds and kilograms.  
 
·...

 
© Adam Equipment Company 2011  Page  
4 
 
 
2.0  TECHNICAL SPECIFICATIONS 
2.1  SPECIFICATIONS FOR THE LOCAL SCALE  
 
Model #  CBD 4 
CBD 8a CBD 8 
CBD 16a  CBD 16 
CBD 35a  CBD 32 
CBD 70a  CBD 48 
CBD 100a   
Maximum  
Capacity  4 kg / 
8 lb  8 kg / 
16 lb  16 kg / 
35 lb  32 kg / 
70 lb  48 kg / 
100 lb 
Readability  0.0001 kg / 
0.0002 lb  0.0002 kg /
 
0.0005 lb  0.0005 kg / 
0.001 lb   0.001 kg / 
0.002 lb  0.002 kg / 
0.005 lb 
Tare Range  -4 kg /  -8lb -8 kg / 
-9.9995 lb  -16 kg / 
-35 lb...

 
© Adam Equipment Company 2011  Page  
5 
 
2.3  COMMON SPECIFICATIONS 
 
Interface  Bi-directional RS-232 Interface 
Optional USB Serial Interface  
Stabilisation Time  2 Seconds   
Operating Temperature  0°C - 40°C  
Power supply   115/230 VAC 50/60Hz. or 
12 VDC 800 mA from external power supply for USA   
Calibration  Automatic external   
Display   3 x 6 digits LCD digital display 
 
Housing  Indicator ABS Plastic,  Stainless Steel platform  
Pan size  225 x 275mm 
8.9” x 10.8”   
Overall...

 
© Adam Equipment Company 2011  Page  
6 
 
 
3.0  INSTALLATION 
3.1  LOCATING THE SCALES 
 
     
 
 
 
 
 
 
 
·  The  scales  should  not  be  placed  in  a  location  
that will reduce the accuracy.  
 
· Avoid  extremes  of  temperature.  Do  not  place  
in  direct  sunlight  or  near  air  conditioning 
vents. 
 
· Avoid  unsuitable  tables.  The  table  or  floor  
must be rigid and not vibrate.  
 
· Avoid  unstable  power  sources.  Do  not  use  
near large users of electricity such as...

 
© Adam Equipment Company 2011  Page  
7 
 
adjusted  such  that  the  bubble  in  the  spirit  level  i s  in  the  centre  of 
the level and the scale is supported by all four fe et.  
 
 
 
·  AC  powered  scales,  attach  the  power  cable  to  the  c onnector  on 
the  bottom    of  the  scale  base.  If  using  the  externa l  plug  in  power 
supply module (USA) connect it to the socket on the  side.   
 
·  The power switch is located at the right side of t he scale base. 
 
·  The  scale  will...

 
© Adam Equipment Company 2011  Page  
8 
 
REMOTE SCALE CONNECTION 
  
The cable for the load cell goes to a 9 pin D-submi niature plug connector with 
the following connections: 
  Pin numbers  Connection 
Pins 1,2     - Excitation (0 V) 
Pins 4,5  + Excitation (+5 V) 
Pin 7  + Signal 
Pin 8  - Signal 
   
(The sense wires connections of a six wire load cel l are not used and should  
be connected to the respective Excitation pins).  
REMOTE SCALE SET UP 
The remote scale should set for a realistic...