Acumen Camera IP Speed Dome Series AiPE1H User Manual

 20 
Chapter 3-5-2 Weighted Streaming Mode Weighted streaming mode is activated when an alarm went off.    The streaming goes to the maximum speed, for example 30 FPS.    If there is no alarm activity, the streaming stays one frame per second for saving bandwidth and storage.    

 21 
  
 
Chapter 3-5-3 Video Quality To setup video quality, please adjust brightness, contrast, hue, saturation, and sharpness accordingly. 
 
Chapter 3-6 PTZ Settings To setup PTZ preset points, please select Camera ID (RS-485ID) first.    For RS-485ID, please refer to PTZ user manual for detail.    Once RS-485ID has been set, please select preset point.    Move the lens to desired position by using pan, tilt, and zoom buttons.    Adjust the lens’ iris and focus by using iris and focus buttons....

 22 
 
 
 
 
Chapter 3-6-2 PTZ Schedule Settings To setup PTZ scheduling, please select PTZ schedule link.    Use the mouse select on the radio button of the preset types, None, Autopan, Preset #1, Preset #2, Preset #3, and Preset #4. 
Click on the hour of the calendar control to configure the preset action.  

 23 
  
Chapter 3-7 SD Card Recording To record video on SD Card, please insert SD card into the SD card slot.    Enable SD card recording feature.    The AiP camera can start to record video into the SD card.  
Chapter 3-7-1 SD Card Recording Setting For SD card recording setting, please see the following for detail. 
  SD Recording: Enable SD card recording.  Alarm/Motion Triggering: Digital input and motion detection SD card recording.   Recording Time: Post alarm recording time.  Continuous:...

 24 
 Mount: Manually mount SD card.  Un-mount: Manually un-mount SD card.  To un-mount the SD card, please click “un-mount SD Card” button.    It might crash the file system of the SD card, if a user does not un-mount the SD card properly. 
  
Chapter 3-8 Alarm Settings H.264 D1 video server or AiP camera’s hardware alarm system contains motion detection, alarm sensors, and one alarm/relay output.    Many alarm features such as motion/alarm email notification and FTP archiving can be found at this...

 25 
 
For video encoder model, since there are two alarm outputs, a user can specify alarm output time.  
Chapter 3-8-3 Motion Area Once above information get set, please configure the motion area of the monitored environment.    To configure motion area, perform mouse click on the video area. 
 
 
Chapter 3-8-4 Audio Detection For audio model, the AiP camera has audio detector detecting acoustic level.    If the volume exceeds the audio sensitivity value, audio detector triggers an alarm for...

 26 
  
Chapter 3-9 Audio Setting Audio setting is based on the following:   MIC Volume: MIC or line input volume  Audio Input Mode: Choose MIC input or Line input.  Audio Input Gain: Voice input gain magnification  Audio Output Volume: Line output volume adjustment  Audio Coding Type: G.711 u-Law  Sample Rate: Audio sample rate  Bit Rate: Audio bit rate. 
 
  

 27 
Appendix  
Advance Network DDNS and PPPoE Technologies 
The advantage of using DDNS and PPPoE is to save the cost of IP address.    H.264 AVC AiP camera’s PPPoE service gets a dynamic global IP address after system reboot.   This IP address may get changed periodically.    This is the address needed to access the video server over Internet.    When ISP re-assigns a new IP address to H.264 AVC AiP camera, H.264 AVC AiP camera notifies DDNS service.    A remote PC can access H.264 AVC AiP camera by...

 28 
 
 
 
 
 
 
iPhone Access To use Live Cams Pro (Eggman Technologies Inc.) for AI AiP cameras.  Please use your iPhone and select AppStore for download Live Cams Pro application developed by Eggman Technologies Inc.    Execute Live Cams Pro application. Please click on “Add Camera” button on your phone while using Live Cams Pro. Task bar gets prompted as below:  Please selection one of the following drivers for cameras: Profile 1: H.264 HD or D1 AiP camera. 
 
 
 
 
 
  
Android Access Please use...

 29 
 
Please click on Manage Cameras button. A list of camera names shows on the screen. Please select one of the cameras and click on Edit button.  
 
“Add/Edit AiP camera” dialog box gets prompted for editing an AiP camera or a DVR. 
 
In “Add/Edit AiP camera” dialog box, please enter the following information:  
1. Name: Name of the AiP camera or DVR’s camera 2. Category: Please select AI. 3. Type: Select device type, AI D1/ AI HD/AI DVR. 4. IP Address: Please type IP address, for example...