Acer Xs S10 Users Guide

							31
EnglishLanguage
LanguageSets a language for the OSD menus. Use   to 
select your preferred language.
•Press   to confirm the selection.
Downloaded From projector-manual.com Acer Manuals 
						

							30
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following 
troubleshooting guide. If the problem persists, please contact your local reseller 
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears 
onscreen•Make sure all the cables are correctly connected as 
described in the Getting Started section.
•Ensure none of the connector pins are bent or 
broken.
•Check if the projection lamp has been securely 
installed. Please refer to the Replacing the Lamp 
section.
•Make sure you have removed the lens cap and the 
projector is switched on.
2 Partial, scrolling 
or incorrectly 
displayed image 
(For PC (Windows 
95/98/2000/XP/
Win7/Vista))
•Press RESYNC on the control panel or remote 
control.
•For an incorrectly displayed image:•Open My Computer > Control Panel, and 
then double-click the Display icon.
•Select the Settings tab.•Verify that your display resolution setting is 
lower than or equal to 1600 x 1200, 1920 x 
1080.
•Click the Advanced Properties button.
If the problem still appears, change the monitor display 
you are using and follow the steps below:
•Verify that the resolution setting is lower than 
or equal to 1600 x 1200, 1920 x 1080.
•Click the Change button under the 
Monitor tab.
•Click Show all devices > Standard monitor 
types under the SP box, and choose the 
resolution mode you need under the Models 
box.
•Verify that the resolution setting of the 
monitor display is lower than or equal to 1600 
x 1200, 1920 x 1080.
Downloaded From projector-manual.com Acer Manuals 
						

							31
English
3 Partial, scrolling 
or incorrectly 
displayed image
(For notebooks)•Press RESYNC on the control panel or remote 
control.
•For an incorrectly displayed image:•Follow the steps for item 2 (above) to adjust 
the resolution of your computer.
•Press the toggle output settings. Example: 
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8], 
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP 
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•If you experience difficulty changing resolutions or 
your monitor freezes, restart all equipment 
including the projector.
4 The screen of the 
notebook 
computer is not 
displaying your 
presentation
•If you are using a Microsoft® Windows® based 
notebook: Some notebook PCs may deactivate their 
own screens when a second display device is in use. 
Each has a different way to be reactivated. Refer to 
your computers manual for detailed information.
•If you are using an Apple® Mac® OS based 
notebook: In System Preferences, open Display and 
select Video Mirroring On.
5 Image is unstable 
or flickering
•Use Tracking to correct it. Refer to the Image 
section for more information.
•Change the display color setting on your computer.
6 Image has vertical 
flickering bar
•Use Frequency to make an adjustment. Refer to 
the Image section for more information.
•Check and reconfigure the display mode of your 
graphics card to make it compatible with the 
projector.
7 Image is out of 
focus
•Make sure the lens cap is removed.
•Adjusts the focus ring on the projector lens.
•Make sure the projection screen is within the 
required distance:
S1110/T200/XS-S10/S1210/T210/XS-X10/S1210Hn/
S1213/T212/XS-X13/S1213Hn/T212DT/XS-X13HG: 1.32 
to 12 feet (0.4 to 3.7 meters)
S1310W/T220/XS-W10/S1310WHn/S1313W/
S1313WHn: 0.98 to 10.5 feet (0.3 to 3.2 meters)
Refer to the How to Get a Preferred Image Size by 
Adjusting Distance and Zoom section for more 
information.
Downloaded From projector-manual.com Acer Manuals 
						

							32
English
Problems with the Projector
8 Image is stretched 
when displaying a 
widescreen 
DVD titleWhen you play a DVD encoded in anamorphic or 16:9 
aspect ratio you may need to adjust the following 
settings:
•If you play a 4:3 format DVD title, please change the 
format to 4:3 with the projector OSD.
•If the image is still stretched, you will also need to 
adjust the aspect ratio. Set up the display format to 
16:9 (wide) aspect ratio on your DVD player.
9 Image is too small 
or too large
•Adjust the zoom lever on the top of the projector.
•Move the projector closer to or further from the 
screen.
•Press MENU on the control panel or remote 
control. Go to Image > Aspect Ratio and try 
different settings.
10 Image has slanted 
sides
•If possible, reposition the projector so that it is 
centered on the screen and below the bottom of the 
screen.
•Press the Keystone correction keys on the control 
panel or remote control until the image becomes 
square.
•Press MENU on the control panel or remote 
control to open the OSD menu. Go to Image > 
Keystone to make adjustments.
11 Image is reversed
•Select Image > Projection, Image > 
Projection Location on the OSD and adjust the 
projection direction.
# Condition Solution
1 The projector stops responding 
to all controlsIf possible, turn off the projector, then 
unplug the power cord and wait at least 30 
seconds before reconnecting power.
2 Lamp burns out or makes a 
popping soundWhen the lamp reaches the end of its useful 
life, it will burn out and may make a loud 
popping sound. If this happens, the projector 
will not turn on until the lamp module has 
been replaced. To replace the lamp, follow 
the procedures in the Replacing the Lamp 
section.
Downloaded From projector-manual.com Acer Manuals 
						

							33
EnglishOSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its 
recommended operating temperature and must be allowed to 
cool down before it is used. Please also check the dust filters if 
they are installed. If the dust filter is clogged with dust, please 
clean it.
Replace the lamp - the lamp is about to reach its maximum 
lifetime. Prepare to replace it soon.
Fan Fail.
Lamp will automatically turn off soon.
Projector Overheated.
Lamp will automatically turn off soon.
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!
Downloaded From projector-manual.com Acer Manuals 
						

							34
English
LED & Alarm Definition Listing
LED Messages
Message Power LED LAMP LED TEMP LED
Red Blue Red Red
Standby
(Power cord plugged in)V-- -- --
Power on -- V -- --
Lamp retry -- Quick 
flashing-- --
Turning off (Cooling 
state)Quick 
flashing-- -- --
Turning off (Cooling 
completed)V-- -- --
Error (Thermal failure) -- V -- V
Error (Fan lock failure) -- V -- Quick 
flashing
Error (Lamp breakdown) -- V V --
Error (Color wheel 
failure)-- V Quick 
flashing--
Downloaded From projector-manual.com Acer Manuals 
						

							35
EnglishReplacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the 
lamp.
The projector will detect the lamp life itself. It will show you a warning message 
Lamp is approaching the end of its useful life in full power operation. 
Replacement Suggested! When you see this message, change the lamp as soon 
as possible. Make sure the projector has been cooled down for at least 45 
minutes before changing the lamp.
Warning: Lamp compartment is hot! Allow it to cool down before 
changing lamp!
To remove the lamp:
1 Turn the projector off by pressing   (POWER).
2 Allow the projector at least 45 minutes to cool down.
3 Disconnect the power cord.
4 Use a screwdriver to remove the screws from the cover. (Illustration #1)
5 Push up and remove the cover.
6 Remove and dispose of the lamp protection film (Illustration #2).
7 Remove the lamp connector from the projector and the screw that secures 
the lamp module (Illustration #3).
8 Lift the handle so that it stands up. Pull out the lamp module by force 
(Illustration #4).
To replace the lamp module, use a new lamp and follow illustrations #  - # .
Warning: To reduce the risk of personal injury, do not drop the 
lamp module or touch the lamp bulb. The bulb may shatter and 
cause injury if it is dropped.
1
8
1 2
8
7
8
6 54 3
1
2
1
58
Downloaded From projector-manual.com Acer Manuals 
						

							36
English
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the 
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and 
secure the mount base.
Note: Screws are not included. Please obtain the appropriate 
screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of cylinder screws.
20 mm13mm
8.4mm130 mm
49.9mm
Short Rod
Screw Type A
50 mm length / 8 mm diameter -Ceiling Mount Base
- Attach to ceiling
Long Rod
Extension Rod
Allen Key
- For tighten/loosen
Tightening Screw
Medium RodLarge Cylinder Cap
Downloaded From projector-manual.com Acer Manuals 
						

							37
English3 Use the appropriate number of screws for the projector size to attach the 
projector to the ceiling mount bracket.
Note: It is recommended that you keep a reasonable space 
between the bracket and the projector to allow for proper heat 
distribution. Use two washers for extra support, if deemed 
necessary.
4 Attach the ceiling bracket to the ceiling rod.
Large Washer
Projector Bracket
Supports projector and 
allows for adjustments   Screw Type B
Spacer
- For heat dissipation
Screw Type A
50 mm length - 
/8 mm diameterLarge Cylinder Cap
Allen Key
- For tighten/loosen Tightening Screw
Downloaded From projector-manual.com Acer Manuals 
						

							38
English
5 Adjust the angle and positioning as necessary.
Note: The appropriate type of screw and washer for each model is 
listed in the table below. 3 mm diameter screws are enclosed in 
the screw pack.
Models Screw Type B Washer Type
Diameter (mm) Length (mm) Large Small
S1110/T200/XS-S10/
S1210/T210/XS-X10/
S1210Hn/S1213/T212/XS-
X13/S1213Hn/T212DT/
XS-X13HG/S1310W/T220/
XS-W10/S1310WHn/
S1313W/S1313WHn325VV
30
Allen KeyTightening Screw
Allen Key
Tightening Screw
96.09 mm
149.90 mm
18.46 mm
83.27 mm
12.11 mm
34.26 mm
Downloaded From projector-manual.com Acer Manuals