Acer Travelmate C210 Service Guide
Have a look at the manual Acer Travelmate C210 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 253 Remove BIOS Password: TIf you key in wrong Supervisor Password for three time, “System Disabled” would display on the screen. See the image below.
54Chapter 2 TIf you need to solve BIOS password locked problem, you can run BIOS_PW.EXE 1. Key in “bios_pw 14452 0” 2.Choose one upper-case string TReboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password.
Chapter 357 This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: TWrist grounding strap and conductive mat for preventing electrostatic discharge TPhilips screw drivers TFlat head screwdriver NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components. When you remove the middle cover, please be careful not to scrape the cover. Chapter 3 Machine Disassembly and Replacement
58Chapter 3 General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 1.Turn off the power to the system and all peripherals. 2.Unplug the AC adapter and all power and signal cables from the system. 3.Remove the battery pack. NOTE: TravelMate C210 series product uses tape to fasten the antenna/cable, you may need to tear the tape before you remove the antenna. NOTE: The disassembly is based on an engineering sample, therefore, the number of the screws and the color of the system may differ from a finish-good unit.
Chapter 359 Disassembly Procedure Flowchart The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the then disassemble the inside assembly frame in that order. Start Battery HDD CoverMini PCI CoverODD ModuleDIMM Cover M3L4*1 M2.5L6*1Keyboard HDD Module HDD HolderHDD Drive ODD BracketM2L3*4 Optical Drive Optical Device Board ODD ConnectorM2L4*2 Hinge CoversKeyboard Support PlateMiddle Cover RTC Battery Memory (upgrade)Wireless LAN Card Memory/ MDC board Disconnect Bluetooth LCD Module M2.5L5*4 Upper Assembly M2.5L6*2 M2L6*12 Lower Assembly Toucpad CoverLower case left coverLower case right cover Touchpad ButtonTouchpad Scroll KeyTouchpad Touchpad Cable Main Board Assembly Heatsink ModuleSpeaker ModuleExtension BoardCPU Main Board Inverter Button Board LED Board Main Antenna LCD/w cable, brakets LCD Panel LCD BracketsLCDLCD Coaxial Cable M2L8*3 M2L4*4 M2L4*2 M2L4*1 M2L4*2 M2L4*1*4*1 *2 M2L4.5*2 M2L4.5*2 M2L4.5*2 M2L4.5*2 M2L3*8 for CMO
60Chapter 3 Removing the Battery Pack 1.Release the battery lock. 2.Slide the battery latch then remove the battery.
Chapter 361 Removing the HDD Module/ODD Module/Memory/Wireless LAN Card/ LCD Module and the Keyboard Removing the Hard Disk Drive Module 1.Remove the two screws fastening the HDD cover. 2.Detach the HDD cover from the notebook. 3.Pull out the hard disk drive then detach it from the main unit. Removing the Optical Disk Drive Module 1.Slide the ODD latch then remove the ODD module from the main unit carefully. Removing the Memory 1.Remove the two screws that fasten the DIMM door. 2.Detach the DIMM door. 3.Pop out the memory then remove it. Removing the Wireless LAN Card 1.Remove the two screws holding the wireless LAN cover. 2.Detach the wirless cover.
62Chapter 3 3.Disconnect wireless main and auxiliary antenna. 4.Pop out the wireless LAN card then remove it. Removing the LCD Module 1.Remove two screws holding the left and the right hinge cover. 2.Remove the right hinge cover. 3.Remove the left hinge cover. 4.Turn over the entire LCD module as shown. 5.Disconnect the six screws fastening the middle cover. 6.Detach the middle cover carefully. 7.Then disconnect the LCD cable.