Acer TravelMate 7730 7730g User Manual

							Chapter 3: Replacing notebook components73
Replacing the secondary hard drive
Tools you need to complete this task:
Screws removed during this task:
Locating components:
To replace the secondary hard drive:
1Complete the steps in “Preparing the notebook” on page 55.
2Loosen the hard drive bay cover screws (these screws cannot be removed).
Phillips #0 screwdriver
4 chrome M3×3.5 (Hard 
drive bracket)
Secondary hard drive bay
Screw ScrewScrew 
						

							74Chapter 3: Replacing notebook components
3Use the thumb notch to lift the hard drive bay cover, then remove it. Be careful not 
to break off the tabs located on the end of the cover opposite the thumb notch.
4Using the plastic tab, lift straight up on the hard drive, then remove it.
5If your new hard drive already includes the hard drive bracket, go to step Step 10.
-OR-
If you need to move the hard drive bracket from your old hard drive to your new 
hard drive, go to step Step 6.
6Remove the screws that secure the hard drive to the hard drive bracket.
Thumb notch
Screw
ScrewScrew
Screw 
						

							Chapter 3: Replacing notebook components75
7Remove the bracket from the old drive.
8Insert the new drive label side up onto the bracket so the screw holes line up.
9Replace the screws that secure the bracket to the drive.
10Slide the new hard drive kit into your notebook.
11Replace the cover, then tighten the screws. 
						

							76Chapter 3: Replacing notebook components
Replacing the optical drive
Tools you need to complete this task:v
Locating components:
To replace the optical drive:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the screw and cover that secures the DVD drive to your notebook.
Flat-blade driver Scribe or non-marring - OR -
Phillips #0 screwdriver
Optical drive
Screw 
						

							Chapter 3: Replacing notebook components77
3Carefully slide the drive out of the drive bay.
Important: Use a small screwdriver or other pointed tool to push on the 
DVD bracket and slide the drive out of the bay.
4Slide the new DVD drive into the drive bay. Make sure that the drive fits securely in 
the bay.
5Replace the screw and cover removed in Step 2.
DVD bracket 
						

							78Chapter 3: Replacing notebook components
Replacing the keyboard cover
Tools you need to complete this taskv
Screws removed during this task:
To replace the keyboard cover:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the two keyboard cover screws from the inside of the battery 
compartment.
3Turn your notebook over so the top is facing up.
4Open the LCD panel to the fully opened position.
5Insert the small flat-blade screwdriver under each of the hinge covers and gently 
pry them up.
Flat-blade driver Scribe or non-marring tool- OR -
Phillips #0 screwdriver
2 black M2.5×5 
(Keyboard cover)
ScrewScrew 
						

							Chapter 3: Replacing notebook components79
6Insert the small flat-blade screwdriver under each end of the keyboard cover and 
gently pry it up.
7Pull the cover off the notebook by lifting the back corners of the cover. Be careful 
to not damage the LCD panel.
8Replace the keyboard cover by first inserting the tabs located on the front of the 
cover into the slots provided, then pressing down on the back. Press down on the 
cover in several places until it clicks in place. The cover is correctly mounted when 
you can run you finger along the cover and find no loose spots. The cover should be 
flat all the way across.
Caution: If the cover is not correctly replaced, your notebook could be 
damaged when you try to close the LCD panel.
9Close the LCD panel.
10Turn your notebook over so the bottom is facing up.
11Replace the screws removed in Step 2. 
						

							80Chapter 3: Replacing notebook components
Replacing the keyboard
Tools you need to complete this task:v
Screws removed during this task:
To replace the keyboard:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the keyboard cover by following the steps in “Replacing the keyboard 
cover” on page 78.
3Lift the center of the back edge of the keyboard slightly and, at the same time, 
press inward on the left side and then the right side. This will release the keyboard 
from the side tabs.
4Slowly slide the keyboard toward the LCD panel to release the keyboard retaining 
tabs located on the front edge of the keyboard.
5Carefully rotate the keyboard toward you so it lies keys-down on top of your 
notebook. Be careful not to damage the LCD panel.
Flat-blade driver Scribe or non-marring tool- OR -
Phillips #0 screwdriver
2 black M2.5×5 
(Keyboard cover) 
						

							Chapter 3: Replacing notebook components81
6Swing the keyboard connector clip upward, then slide the cable out of the clip. Be 
careful not to touch or damage any other components.
7Place the new keyboard keys-down on your notebook with the space bar away from 
you.
8Make sure the keyboard connector clip is fully lifted up, insert the cable into the 
connector, then swing the clip downward to lock the connector in place.
Important: The keyboard cable is correctly oriented if it is not twisted and 
the blue band is facing up.
9Insert the tabs on the front edge of the keyboard into the slots under the palm rest. 
You may need to press down on the keyboard keys along the front edge of the 
keyboard to seat the retaining tabs into their corresponding slots.
10Gently press the keyboard down until it is flat all the way across. Be careful to not 
damage the LCD panel.
11Press down on the right side and left side of the keyboard to make sure that the 
side tabs secure the keyboard.
12Replace the keyboard cover by following the steps in “Replacing the keyboard 
cover” on page 78.
Clip 
						

							82Chapter 3: Replacing notebook components
Replacing the power button board
Tools you need to complete this task:v
Screws removed during this task:
To replace the status indicator board:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the keyboard cover by following the steps in “Replacing the keyboard 
cover” on page 78.
3Open the keyboard compartment by following the steps in “Replacing the 
keyboard” on page 80.
Important: You do not need to disconnect the keyboard cable from the 
system board to complete this procedure.
4Swing the black connector clip upward, then lift the cable out of the connector. Be 
careful not to touch or damage any other components.
Flat-blade driver Scribe or non-marring tool- OR -
Phillips #0 screwdriver
2 black M2.5×5 
(Keyboard cover)3 black M2.5×4 (Power 
button board)
Clip