Acer TravelMate 7730 7730g User Manual

							Chapter 3: Replacing notebook components83
5Remove the screws connecting the power button board to the notebook.
6Replace the power button board, then replace the screws removed in Step 5.
7Make sure the black connector clip on the new power button board is swung 
upward, insert the cable into the connector, then swing the clip down to lock the 
connector in place.
Important: The cable is correctly oriented if it is not twisted and the blue 
band is facing up.
8Close the keyboard compartment by following the steps in “Replacing the 
keyboard” on page 80.
9Replace the keyboard cover by following the steps in “Replacing the keyboard 
cover” on page 78.
Screw Screw Screw 
						

							84Chapter 3: Replacing notebook components
Replacing the LCD assembly
Tools you need to complete this task:v
Screws removed during this task:
To replace the LCD assembly:
1Complete the steps in “Preparing the notebook” on page 55.
2Open the memory bay by following the steps in “Adding or replacing memory 
modules” on page 57.
3Open the wireless bay by following the steps in “Replacing the IEEE 802.11 wireless 
card” on page 67.
4If the notebook has wireless networking built in, unplug the wireless antennas by 
following the steps in “Replacing the IEEE 802.11 wireless card” on page 67.
5Taking care to note the cables’ routing and positions as they are installed from 
Acer, slide the antenna cables out of the wireless bay. 
Flat-blade driver Scribe or non-marring - OR -
Phillips #0 screwdriver
4 black M2.5×6.5 
(Hinge-top)2 black M2.5×6.5 
(Hinge-bottom)2 black M2.5×5 
(Keyboard cover) 
						

							Chapter 3: Replacing notebook components85
6Remove the screws on the bottom that secure the LCD panel hinges to the chassis.
7Remove the keyboard cover by following the steps in “Replacing the keyboard 
cover” on page 78.
8Remove the keyboard by following the steps in “Replacing the keyboard” on page 
80.
9Detach the LCD cable from the system board. Use a scribe or other non-marring tool 
to gently push the plug out of the connector.
Caution: The LCD video cable connector is fragile.
Screw Screw 
						

							86Chapter 3: Replacing notebook components
10Taking care to note the cables’ routing and positions as they are installed from 
Acer, pull the antenna cables out from under the system board, then slide the 
antenna cables and LCD cables out from under the retaining clips.
11Remove the screws on the top that secure the LCD panel hinge to the chassis.
12Lift the LCD panel assembly up and away from the notebook.
13Place the new LCD panel assembly onto the notebook, then replace the hinge 
screws removed in Step 11.
14Slide the antenna cables through the retaining clips, then under the system board.
15Slide the LCD cable through the retaining clip, then plug it into the notebook.
16Replace the keyboard by following the steps in “Replacing the keyboard” on page 
80.
17Replace the keyboard cover by following the steps in “Replacing the keyboard 
cover” on page 78.
18Close the LCD panel, turn the notebook over so the bottom is facing up, then 
replace the bottom hinge screws removed in Step 6.
19Route the antenna cables into the wireless bay, then reconnect the antenna wires 
to the wireless card by following the steps in “Replacing the IEEE 802.11 wireless 
card” on page 67.
20Replace the wireless bay cover by following the steps in “Replacing the IEEE 802.11 
wireless card” on page 67.
21Replace the memory bay cover by following the steps in “Adding or replacing 
memory modules” on page 57.
Screw Screw Screw Screw 
						

							Chapter 3: Replacing notebook components87
Replacing the inverter
Tools you need to complete this task:v
Screws removed during this task:
To replace the inverter:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the LCD panel by following the steps in “Replacing the LCD assembly” on 
page 84.
3Remove the rubber inserts from the front of the LCD panel assembly.
Flat-blade driver Scribe or non-marring tool- OR -
Phillips #0 screwdriver
2 black M2.5×6.5 
(Hinge-bottom)2 black M2.5×5 
(Keyboard cover)
6 black M2.5×5 (LCD 
front panel)
4 black M2.5×6.5 
(Hinge-top)
Insert
Insert
InsertInsert
Insert Insert 
						

							88Chapter 3: Replacing notebook components
4Remove the screws from the front of the LCD panel assembly.
5Carefully separate the front and back of the LCD panel assembly.
6Lift the inverter from the LCD panel assembly.
7Disconnect the connectors from the old inverter and connect them to the new 
inverter.
8Align the holes in new inverter with the pegs in the LCD lid, then press the inverter 
into place.
9Press the LCD panel front and back together. Press the two halves together in 
several places until they click in place. You should find no loose spots or spots 
where the two halves do not meet.
10Replace the LCD panel assembly screws removed in Step 4.
11Replace the rubber inserts removed in Step 3.
12Replace the LCD panel by following the steps in “Replacing the LCD assembly” on 
page 84.
Screw
ScrewScrew
Screw
ScrewScrew 
						

							Chapter 3: Replacing notebook components89
Replacing the LCD panel
Tools you need to complete this task:v
Screws removed during this task: 
To replace the LCD panel:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the LCD panel by following the steps in “Replacing the LCD assembly” on 
page 84.
Flat-blade driver Scribe or non-marring tool- OR -
Phillips #0 screwdriver
2 black M2.5×6.5 
(Hinge-bottom)2 black M2.5×5 
(Keyboard cover)
6 black M2.5×5 (LCD 
front panel)8 black M2.5×5 (LCD 
panel to LCD panel lid)1 black M2.5×5 
(Grounding screw)
4 chrome M2×3 
(Hinge bracket)2 chrome M2×3 
(Web cam)
4 black M2.5×6.5 
(Hinge-top) 
						

							90Chapter 3: Replacing notebook components
3Remove the rubber inserts from the front of the LCD panel assembly.
4Remove the screws from the front of the LCD panel assembly.
5Carefully separate the front and back of the LCD panel assembly.
Insert
Insert
InsertInsert
Insert Insert
Screw
ScrewScrew
Screw
ScrewScrew 
						

							Chapter 3: Replacing notebook components91
6Remove the grounding screw from the LCD panel lid.
7Remove the screws that secure the LCD panel to the LCD panel lid.
8Remove the inverter by following the steps in “Replacing the inverter” on page 87.
9Remove the old LCD panel from the LCD panel lid.
10Remove the hinges from the old LCD panel and install them on the new panel by 
following the steps in “Replacing the LCD panel hinges” on page 92.
11Remove the web cam from the old LCD panel and install it on the new panel by 
following the steps in “Replacing the web cam” on page 94.
12Place the new LCD panel into the LCD panel lid.
13Replace the inverter by following the steps in “Replacing the inverter” on page 87.
14Feed the wiring back into the hinge channels.
15Replace the screws that were removed in Step 7.
16Press the LCD panel front and back together. Press the two halves together in 
several places until they click in place. You should find no loose spots or spots 
where the two halves do not meet.
17Replace the LCD panel assembly screws removed in Step 4.
18Replace the rubber inserts removed in Step 3.
19Replace the LCD assembly by following the steps in “Replacing the LCD assembly” 
on page 84.
Screw
Screw Screw
Screw
Screw Screw Screw
Screw Screw 
						

							92Chapter 3: Replacing notebook components
Replacing the LCD panel hinges
Tools you need to complete this task:v
Screws removed during this task:
To replace the LCD panel hinges:
1Complete the steps in “Preparing the notebook” on page 55.
2Remove the LCD panel assembly by following the steps in “Replacing the LCD 
assembly” on page 84.
3Remove the LCD panel by following the steps in “Replacing the LCD panel” on 
page 89.
4Remove the screws that secure the hinge bracket to the LCD panel.
5Place the new hinge bracket onto the LCD panel.
Flat-blade driver Scribe or non-marring tool- OR -
Phillips #0 screwdriver
2 black M2.5×6.5 
(Hinge-bottom)2 black M2.5×5 
(Keyboard cover)
6 black M2.5×5 (LCD 
front panel)8 black M2.5×5 (LCD 
panel to LCD panel lid)1 black M2.5×5 
(Grounding screw)
4 black M2.5×6.5 
(Hinge-top)
4 chrome M2×3 
(Hinge bracket)
Screw
Screw Screw Screw