Acer Travelmate 730 Service Guide
Here you can view all the pages of manual Acer Travelmate 730 Service Guide. The Acer manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 51
Chapter 345 Removing the Hard Disk Drive Module 1. Remove the screw of the hard disk cover, then remove the HDD cover. 2. Pull the plastic tag to remove the HDD module. 730sg-1.book Page 45 Wednesday, December 1, 1999 6:03 PM
Page 52
46Chapter 3 Removing the Floppy Disk Drive Module 1. Remove the screw as shown here. 2. Disconnect the FDD FPC cable. 3. Slide out the FDD module from the upper case smoothly. WARNING: Be careful not to break the FDD FPC cable, when sliding out the module. 730sg-1.book Page 46 Wednesday, December 1, 1999 6:03 PM
Page 53
Chapter 347 Disassembling the Main Unit Removing the Keyboard 1. First, release the left and right hinge caps. 2. Slide the middle cover to the right, then remove it from the main unit. 3. Release the middle hinge cap. 4. Hold the keyboard upward. 5. Disconnect the keyboard cable from the mainboard. 6. Remove the keyboard. 730sg-1.book Page 47 Wednesday, December 1, 1999 6:03 PM
Page 54
48Chapter 3 Removing the LCD Module 1. Remove the two screws as shown. 2. Disconnect the LED/inverter board FPC cable and the LCD FPC cable from the mainboard. 3. Release the two screws on the main unit. 4. Lift up the LCD module cautiously. Removing the TouchPad Module 1. Use a flat-bladed plastic screw driver to detach the touchpad frame from the upper case. 2. Remove the left and right touchpad button and the touchpad lower button. 730sg-1.book Page 48 Wednesday, December 1, 1999 6:03 PM
Page 55
Chapter 349 3.Disconnect the touchpad cable 4.Remove the touchpad board. Removing the CPU 1.Release the four screws on the heatsink plate. 2.Remove the heatsink plate. 3.Release the six screws on the CPU heatsink. 4.Remove the CPU heatsink. 5.Loose up the CPU secure knot. 6.Remove the CPU. 730sg-1.book Page 49 Wednesday, December 1, 1999 6:03 PM
Page 56
50Chapter 3 Removing the RTC 1. Use a plastic flat bladed screw driver to remove the RTC battery from its socket NOTE: To replace the RTC battery, press the RTC battery into the socket. Separating the Lower Case from the Upper Case 1. Disconnect the touchpad cable from the mainboard. 2. Release the six screws from the bottom of the main unit as shown below. 3. Remove the upper case backward. 730sg-1.book Page 50 Wednesday, December 1, 1999 6:03 PM
Page 57
Chapter 351 4.Disconnect the LCD cover switch connector from the mainboard. 5.Separate the upper case from the lower case. Removing the Fan 1.Remove the fan cable from the mainboard. 2.Release the two screws. 3.Remove the fan from the mainboard. Removing the DC-DC Charger Board 1.Release the screw as shown. 2.Remove the DC-DC charger board from the mainboard. 730sg-1.book Page 51 Wednesday, December 1, 1999 6:03 PM
Page 58
52Chapter 3 Removing the System Board 1. Remove the four screws on the mainboard as shown below. 2. Remove the mainboard from the lower case with caution. Removing the Audio Jack Cover 1. Remove the audio jack cover from the mainboard. Removing the PCMCIA Socket 1. From the back of the mainboard, release the four screws as shown below. 2. Detach the PCMCIA socket from the mainboard. Removing the Modem Power Cable 1. Disconnect the modem power cable from the mainboard. 2. Remove the cable. 730sg-1.book...
Page 59
Chapter 353 Disassembling the LCD Module Removing the LCD Bezel 1. Remove the five mylars from the LCD module. NOTE: 13.3” and 14.1” LCD have 5 mylars; 15” has only 3 mylars. 2. Remove the five screws from the LCD module. NOTE: 13.3” and 14.1” LCD have 5 screws; 15” has only 3 screws. 3. Snap the LCD bezel off carefully. Removing the Speaker Assembly Module 1. Turn the LCD module over. WARNING: Be careful not to break the LCD panel. Place a soft cushion below the LCD panel. 2. Remove the three...
Page 60
54Chapter 3 3.Remove the speaker to LED cable. 4.Remove the speaker assembly module. Removing the Inverter Board 1.Remove the LCD power cable and inverter to LED cable from the inverter. 2.Remove the two screws as shown below. 3.Remove the inverter board. Removing the LCD Bracket 1.Release the four screws as shown below. 2.Take out the LCD panel from the LCD module carefully. 730sg-1.book Page 54 Wednesday, December 1, 1999 6:03 PM