Acer Travelmate 6592g Service Guide

Chapter 381
LCM Module Reassembly Procedure
Replacing the LCD Panel
1.Align the LCD brackets the four screw holes (two on each side) on the LCD Panel as shown.
2. Secure the LCD brackets to the LCD panel.
3. Insert the cable into the cable connector on the LCD Panel as shown.
4. Align the LCD Panel cable as shown and press down to engage the adhesive pads. 

82Chapter 3
5.Place the WebCam Module in the mounting as shown.
6. Place the Inverter Board in the mounting and secure with the screw provided.
7. Place the LCD Panel in the mounting and secure the three panel connectors as shown. 

Chapter 383
8.Secure the LCD Panel with the six screws provided.
Replacing the LCM Bezel
1.Locate the bezel correctly and press down the edges until there are no gaps between the bezel and the 
LCM Module,
2. Secure the six screws provided and replace the mylar (small red markers) and rubber screw caps (large 
red markers). 

84Chapter 3
Main Module Reassembly Procedure
Replacing the CPU
1.Insert the CPU into the CPU bracket as shown.
2. Using a screw driver, tighten the screw clockwise as shown to secure the CPU in place.
Replacing the Heatsink and Fan Module
1.Place the Fan Module in the mounting as shown.
2. Place the Heatsink as shown. 

Chapter 385
3.Align the Heatsink Securing Bracket as shown.
4. Secure the five screws and fan connector as shown.
Replacing the I/O Board
1.Insert the board rear edge first as shown.
2. Replace the two screws as shown. 

86Chapter 3
Replacing the Mainboard
1.Ensure that the Mainboard is face up (the Heatsink and CPU are not visible). Place the Mainboard in the 
chassis, rear edge first, and press down to install. Replace the two securing screws as shown.
NOTE: If any resistance is met while installing the  mainboard, ease the computer case outward to clear the 
obstruction.
2. Replace the three connectors in the Mainboard sockets as shown.
3. Secure the Mainboard to the chassis using the two screws provided. 

Chapter 387
Replacing the TouchPad
1.Using both hands, replace the TouchPad, front edge first, as shown.
NOTE: Ensure that the TouchPad cables are accessible once the TouchPad is in place and that all cables 
pass through the casing properly.
Replacing the LCM Module
1. Align the four screw holes on the LCM Module hinges with the corresponding screw holes on the chassis. 
Lower the LCM Module into position as shown. Ensure that the LCM cables are inserted through the 
aperture before proceeding (yellow...

88Chapter 3
Replacing the Antenna Cables
1.Ensure that the three LCM Module cable pass through the Mainboard and are accessible from the 
underside of the computer. Place the three cables in the wiring conduit and secure in place using the 
cable pins on the chassis.
2. Connect the LCM Module cable to the connector on the chassis as shown.
Replacing the Modem
1.Place the Modem in the mounting as shown. Insert the two screws provided to hold the Modem in place. 

Chapter 389
2.Reconnect the Modem  cables as shown.
Replacing the Switch Board
1.Place the Switch Board in the mounting as shown.
2. Secure the Switch Board in place using the screw provided.
Reconnecting the TouchPad
1.Replace the connector as shown. 

90Chapter 3
2.Insert the first cable as shown and lock the latch to secure the cable in place.
3. Insert the second cable as shown and lock the latch to secure the cable in place.
Replacing the Keyboard
1.Using fine tweezers, inse rt the thicker cable into the socket and secu re the locking latch as shown.
2. Using fine tweezers, insert the remaining cable into the socket and secure the locking latch as shown.