Acer Travelmate 5330 Service Guide

Chapter 375
4.Remove the two screws (B) securing the heatsink fan module in place. 
5.Carefully lift up the heatsink fan module. 
Removing the CPU and VGA Heatsink Module
1.See “Removing the Battery Pack” on page 54.
2.See “Removing the Lower Cover” on page 57.
3.See “Removing the Heatsink Fan Module” on page 70.
StepSize (Quantity)ColorTo r q u e
1~2 M2 x L4 (2) Silver 1.6 kgf-cm 

76Chapter 3
4.Remove the four screws securing the VGA board heatsink module (Discrete Model only) and the five 
screw securing the CPU heatsink module. 
5.Carefully remove the heatsink module from the system.
Removing the CPU 
1.See “Removing the Battery Pack” on page 54.
2.See “Removing the Lower Cover” on page 57.
3.See “Removing the Heatsink Fan Module” on page 70.
4.See “Removing the CPU and VGA Heatsink Module” on page 71. 

Chapter 377
5.Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU. 
6.Lift up carefully to remove the CPU. 
NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown. 
Removing the VGA Board (Discrete Model only) 
1.See “Removing the Battery Pack” on page 54.
2.See “Removing the Lower Cover” on page 57. 

78Chapter 3
3.See “Removing the Heatsink Fan Module” on page 70.
4.See “Removing the CPU and VGA Heatsink Module” on page 71.
5.Remove the two screws (B) securing the VGA board to the main board. 
6.Remove the VGA board from the main board.
Removing the LCD Module
1.See “Removing the Battery Pack” on page 54.
2.See “Removing the SD dummy card” on page 55.
3.See “Removing the PC and ExpressCard dummy cards” on page 56.
4.See “Removing the Lower Cover” on page 57.
5.See “Removing the WLAN Board Modules” on...

Chapter 379
8.Turn over the system and remove the two screws (B) from the bottom of the left and right hinges. 
9.Carefully pull out the wireless antenna cables from the hole and release the cables from the latches. 
10.Disconnect the LCD cable connector from the main board. 
StepSize (Quantity)ColorTo r q u e
1~2 M2.5 x L6 (2) Black 3.0 kgf-cm 

80Chapter 3
11 .Remove the two screws (D) from the left and right hinge of the LCD module. 
12.Carefully remove the LCD module from the base unit. 
NOTE: When connecting the cable back to the unit, please note that the cable should be routed well.
Separating the Upper Case from the Lower Case
1.See “Removing the Battery Pack” on page 54.
2.See “Removing the SD dummy card” on page 55.
3.See “Removing the PC and ExpressCard dummy cards” on page 56.
4.See “Removing the Lower Cover” on page 57.
5.See...

Chapter 381
13.See “Removing the CPU” on page 72.
14.See “Removing the VGA Board (Discrete Model only)” on page 73.
15.See “Removing the LCD Module” on page 74.
16.Disconnect the touchpad cable from the TPAD1 connector on the main board. 
17.Disconnect the fingerprint cable from the FPCN1 connector on the main board.  

82Chapter 3
18.Disconnect the launch board cable from the SWITCHCN1 connector on the main board.  

Chapter 383
19.Disconnect the speaker cable from the INTSPK1 connector on the main board. 
20.Remove the fourteen screws (14 x C) from the bottom panel.   
21.Turn the unit over and gently remove the upper case from the lower case. 
StepSize (Quantity)ColorTo r q u e
1~14 M2.5 x L5 (14) Black 2.5 kgf-cm 

84Chapter 3
Removing the Speaker Module
1.See “Removing the Battery Pack” on page 54.
2.See “Removing the SD dummy card” on page 55.
3.See “Removing the PC and ExpressCard dummy cards” on page 56.
4.See “Removing the Lower Cover” on page 57.
5.See “Removing the DIMM” on page 58.
6.See “Removing the WLAN Board Modules” on page 59.
7.See “Removing the Hard Disk Drive Module” on page 61.
8.See “Removing the Optical Drive Module” on page 62.
9.See “Removing the Middle Cover” on page 66.
10.See “Removing the...