Acer Travelmate 4330 Service Guide
Here you can view all the pages of manual Acer Travelmate 4330 Service Guide. The Acer manuals for Notebook are available online for free. You can easily download all the documents as PDF.
Page 71
Chapter 361 5.Remove the three screws securing the ODD bracket and remove the ODD bracket from the ODD module. 6.Insert a pin in the eject hole of the ODD to eject the ODD tray. 7.Press down on the locking catch to release the ODD cover and remove. StepSizeQuantityScrew Type ODD Bracket M2*3 (NL) 3
Page 72
62Chapter 3 Main Unit Disassembly Process Main Unit Disassembly Flowchart Screw List StepScrewQuantityPart No. Switch Cover M2.5*3 (NL) 5 86.TQ602.001 Keyboard M2*3 (NL) 2 86.TQ602.005 Power Board M2*3 (NL) 2 86.TQ602.005 Launch Board M2*3 (NL) 2 86.TQ602.005 LCD Module M2.5*9 (NL) 4 86.TQ602.003 M2.5*5 (NL) 2 86.TQ602.002 Upper Cover M2.5*9 (NL) 17 86.TQ602.003 F/P Reader M2.5*3 (NL) 1 86.TQ602.001 Touch Pad Bracket M2.5*3 (NL) 2 86.TQ602.001 Speaker (L and R) M2.5*3 (NL) 4 86.TQ602.001 Modem Module...
Page 73
Chapter 363 Thermal Module M2.5*3.2 (INTEL) 4 86.TQ602.009 M2*3 (VGA) 4 86.TQ602.008 VGA Module M2*5 (NL) 2 86.TQ602.006 StepScrewQuantityPart No.
Page 74
64Chapter 3 Removing the Switch Cover CAUTION: Using tools to remove the Switch Cover may cause damage to the outer casing. It is recommended that only fingers are used to remove the Switch Cover. 1.See “Removing the Battery Pack” on page 50. 2.Locate and remove the five securing screws as shown. 3.Turn the computer over and open the LCD module fully to expose the Switch Cover. IMPORTANT:The LCD module must be fully open in the horizontal position to remove the switch cover. 4.Lift the Switch Cover as...
Page 75
Chapter 365 Removing the Keyboard 1.See “Removing the Switch Cover” on page 64. 2.Remove the two screws securing the keyboard to the upper case. 3.Lift the keyboard as shown to remove from the chassis. 4.Turn the keyboard over and pull back the securing latch to release the FFC. 5.Remove the keyboard from the chassis. StepSizeQuantityScrew Type Keyboard M2*3 2
Page 76
66Chapter 3 Removing the Power Board 1.See “Removing the Keyboard” on page 65. 2.Disconnect the Power Board cable from the mainboard. 3.Remove the two securing screws from the Power Board. NOTE: The left hand securing screw is shared by the eKey Board. StepSizeQuantityScrew Type Power Board M2*3 2
Page 77
Chapter 367 Removing the Launch Board 1.See “Removing the Keyboard” on page 65. 2.Disconnect the Launch Board cable from the mainboard. 3.Remove the two securing screws from the Launch Board. NOTE: The right hand securing screw is shared by the Power Board. StepSizeQuantityScrew Type Launch Board M2*3 2
Page 78
68Chapter 3 Removing the Antenna 1.See “Removing the WLAN Module” on page 56. 2.Remove the Antenna Cables from the securing guides as shown. 3.Turn the computer over, remove the adhesive tape and disconnect the FCC cables to expose the antenna cables underneath. 4.Secure the FFC cable out of the way using the adhesive tape. 5.Turn the computer over and push the cables through the underside of the chassis.
Page 79
Chapter 369 6.Turn the computer over, and remove the cable from the mainboard as shown. 7.Remove the Antenna Cables from the housing well as shown. NOTE: Place the cables to one side to avoid damage.
Page 80
70Chapter 3 Removing the LCD Module 1.See “Removing the Keyboard” on page 65. 2.See “Removing the Antenna” on page 68. 3.Remove the two securing screws from the bottom of the chassis. 4.Turn the computer over. Disconnect the LCD cable from the top panel. StepSizeQuantityScrew Type LCD Module M2.5*9 (NL) 2