Acer Travelmate 4010 Service Guide

Chapter 353
M2.5*6
(Part number: 86.T23V7.010)Remove the IO bezel then 
you will see.2
M2.5*6
(Part number: 86.T23V7.010)Remove the heatsink cover 
then you will see.1
M2.5*6
(Part number: 86.T23V7.010)Remove the HDD cover then 
you will see.1
M2.5*3
(Part number: 86.T25V7.012)Detach the HDD module  
then you will see.1
M2.5*3
(Part number: 86.T25V7.012)Remove the battery then you 
will see.1
Screw TypeLocationQuantity 

54Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence 
and instructs you on the components that need to be removed during servicing. For example, if you want to 
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in 
that order.
Start
Battery
HDD CoverODD ModuleRAM/Wireless
Cover*2
*2
HDD ModuleWireless LAN
CardMemory
IO BezelE*2
*2
Heatsink
Cover
special...

Chapter 355
Screw List
 
ItemDescription
A SCREW M2.0X3.0-I-NI-NYLOK
B SCREW I2.5*3M-BNIH(M2.5L3)
C SCREW M2.5*4L-BZN-NYLOK
D SCREW M2.0X5-I-NI-NYLOK
E SCREW MM25060IL69
F SCREW M2.0*5-I(NI)(NYLOK)
G SCREW M2.0X2.5-I-NI-NYLOK
H SCREW I2*3M-NIHY (M2L3)
I SCREW M1.7*3.0-I (BK)
J SCREW I3*3.5M-NIH(M3L3.5)
4 screw pads
M*4
LCD Bezel
*6 hinges
*2 brackets
LCD Inverter
LCD
AssemblyLCD Cover
*4
LCD Module
LCDLCD CableLCD Brackets
Antenna set 

56Chapter 3
Removing the Battery Pack
1.Unlock the battery lock.
2.Slide the battery latch as shown then remove the battery pack.
  

Chapter 357
Removing the HDD Module/the Memory and the Wireless LAN Card/the 
Thermal Module and the CPU/ODD Module and LCD Module
Removing the HDD Module
1.Remove the two screws holding the HDD cover.
2.Remove the HDD cover.
3.Detach the HDD module then remove it.
Removing the Memory and the Wireless LAN Card
1.Remove the two screws that secure the RAM/Wireless cover.
2.Remove the RAM/Wireless cover.
3.Pop up the memory then remove it.
4.Disconnect the auxiliary and the main wireless antennae.
5.Pop the...

58Chapter 3
4.Remove the heatsink cover from the main unit.
5.Disconnect the fan cable.
6.Remove the four screws that secure the thermal module.
7.Pull the thermal module outwards then remove it.
NOTE: The edge of the thermal module as shown is very sharp. Be very careful as you remove the thermal 
module.
8.Use a flat-bladed screwdriver to release the CPU lock.
9.Remove the CPU from the socket carefully. 

Chapter 359
Removing the ODD Module
1.Remove the three screws holding the middle cover.
2.Detach the middle cover carefully. 
3.Turn over the keyboard as shown.
4.Disconnect the keyboard cable from the main board then remove the keyboard.
5.Remove the screw that fastens the ODD module.
6.Turn over the notebook computer then detach the ODD module carefully.
NOTE: When you reattach the ODD, please make sure you attach the ODD module completely to the main 
unit. Otherwise, you can not fasten the screw and...

60Chapter 3
.
3.Remove the two screws that secure the keyboard as shown.
4.Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard.
5.Pull out the antenna set with a tweezers then take out the antenna set from the main unit.
.
6.Disconnect the LCD coaxial cable.
7.Remove the four screws holding the right and the left hinge. Two on each side.
8.Then detach the LCD module from the main unit.
. 

Chapter 361
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.Remove the two screws holding the switch board.
2.Remove the switch board.
3.Disconnect the touchpad FFC from the main board.
4.Disconnect the bluetooth cable.
5.Remove the five screws that secure the upper case.
6.Remove the eighteen screws on the bottom as shown.
7.Detach the upper case assembly and place it next to the lower case assembly.
8.Disconnect the microphone cable then remove the upper...

62Chapter 3
4.Remove the three screws that secure the touchpad board.
5.Remove the touchpad board from the upper case.
6.Disconnect the touchpad board to touchpad FFC.
7.Remove the touchpad board to touchpad FFC from the uppwer case assembly.
8.Remove the four screws holding the touchpad bracket.
9.Detach the touchpad bracket from the upper case assembly.
10.Remove the touchpad from the upper case.
11 .Remove the two screws that secure the bluetooth module.
12.Disconnect the bluetooth module then remove...