Acer Projector P5280 User Manual

29
English
Audio setting
Administrator Password
The Administrator Password can be used in both the Enter 
Administrator Password and Enter Password dialog boxes.
•Press   to change the Administrator Password.
•The factory default of Administrator Password is 1234.
If you forgot your administrator password, do the following to 
retrieve the administrator password:
•An unique 6-digit Universal Password which is printed on 
the Security Card (please check accessory in the box). This 
unique password is the...

30
English
Timer setting
Language setting
Timer Start•Press   to start or stop the timer.
Timer Period
•Press   or   to adjust the timer period.
Timer Volume
•Select this function to adjust the notification volume when 
the timer function is enabled and time is up.
Timer Display
•Press   or   to which timer mode to display on the 
screen.
Timer Location
•Choose the location of the timer on the screen.
Language
Choose the multilingual OSD menu. Use the or key 
to select your preferred menu language....

31
EnglishAppendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following 
troubleshooting guide. If the problem persists, please contact your local reseller 
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears 
onscreen•Connected as described in the Getting Started 
section.
•Ensure none of the connector pins are bent or 
broken.
•Check if the projector lamp has been securely 
installed. Please refer to the Replacing the Lamp...

32
English
2 Partial, scrolling 
or incorrectly 
displayed 
image(For PC 
(Windows 95/98/
2000/XP))•Press RESYNC on the remote control or control panel.
•For an incorrectly displayed image:•Open My Computer, open the Control 
Panel, and then double-click the Display 
icon.
•Select the Settings tab.•Verify that your display resolution setting is 
lower than or equal to SXGA (1280 x 1024) 
(P1165/P1165P) or SXGA+ (1400 x 1050) (P1265/
P1265P) or UXGA (1600 x 1200) (P5260i/P5270/
P5280/P5370W series)....

33
English5 Image is unstable 
or flickering•Adjust the Tracking to correct it. Refer to the 
Image Setting section for more information.
•Change the display color depth settings on your 
computer.
6 Image has vertical 
flickering bar
•Use Frequency to make an adjustment. Refer to 
the Image Setting section for more information.
•Check and reconfigure the display mode of your 
graphics card to make it compatible with the 
projector.
7 Image is out of 
focus
•Make sure the lens door is slid on.
•Adjusts...

34
English
OSD Messages
# Condition Message Reminder
1 Message Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its 
recommended operating temperature and must be allowed to 
cool down before it may be used.
Replace the lamp - the lamp is about to reach its maximum 
lifetime. Prepare to replace it soon. 

35
EnglishProblems with the Projector
# Condition Solution
1 The projector stops responding 
to all controlsIf possible, turn off the projector, then 
unplug the power cord and wait at least 30 
seconds before reconnecting power.
2 Lamp burns out or makes a 
popping soundWhen the lamp reaches the end of its useful 
life, it will burn out and may make a loud 
popping sound. If this happens, the projector 
will not turn on until the lamp module has 
been replaced. To replace the lamp, follow 
the...

36
English
LED & Alarm Definition Listing
LED Messages
MessageLamp LED Temp LED Power LED
Red Red Red Blue
Standby 
(power cord plugged in)-- -- V --
Power button ON -- -- -- V
Lamp retry -- -- -- Quick 
flashing
Turning off 
(cooling state)-- -- Quick 
flashing--
Turning off 
(cooling completed)-- -- V --
Error (thermal failure) -- V -- V
Error (fan lock failure) -- Quick 
flashing-- V
Error (lamp breakdown) V -- -- V
Error (color Wheel fail) Quick 
flashing-- -- V 

37
EnglishReplacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the 
lamp.
The projector will detect the lamp life. You will be shown a warning message 
Lamp is approaching the end of its useful life in full power operation. 
Replacement Suggested! When you see this message, change the lamp as soon 
as possible. Make sure the projector has been cooling down for at least 30 
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool...

38
English
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the 
steps below:
1 Drill four holes into a solid, structurally sound part of the ceiling, and 
secure the mount base.
Note: Screws are not included. Please obtain the appropriate 
screws for your type of ceiling.
2 Secure the ceiling rod using the appropriate type of four-cylinder screws.
Ceiling Mount Base    - Attach to ceiling
Screw Type A50 mm length / 8 mm diameter -   
   
Long Rod...