Acer Pd110 Users Guide

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals21
English
4. Procedure as Step.3.
5. Press 
 to save and exit the Users info. menu.
6. The startup screen will display the new wording after restart the projector.
Note:
XEach line can input 35 characters only.
XOnce entering Users info. menu can use remote control to operate only.
XUse Del to delete the previous character.
XUse Space to add a space.
User’s Info          
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals22
English
User Controls
Computer Mode
Image-I
Brightness
Adjusts the brightness of the image.
XPress W to darken image.
XPress X to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts of
the picture. Adjusts the contrast changes the amount of black and white in the image.
XPress W to decrease the contrast.
XPress X to increase the contrast.
Color Temperature
Adjusts the color temperature. The range is from “0” to “4”, the factory default is “2”.
With the higher temperature, the screen looks colder; with the lower temperature, the
screen looks warmer.
Zoom
XPress W to magnify an image up to a factor of eight times on the projection screen.
XPress X to diminish the zoom in image. Lowest available setting is 1/2-size.
Keystone (Keystone Correction)
Adjusts image distortion caused by tilting projection. (±16 degrees)
White Segment
Use the white segment control to set the white peaking level of the DMD chip. “0”
stands for minimal peaking, and “10” stands for maximum peaking. If you prefer a
stronger image, adjust toward the maximum setting.  For a smooth and more natural
image, adjust toward the minimum setting.        
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals23
English
User Controls
Computer Mode
Image-II
Frequency
“Frequency” is for changing the display data frequency to match the frequency of
your computer’s graphic card. When you experience a vertical flickering bar, use this
function to make an adjustment.
Tracking
Choose “Tracking” to synchronize the signal timing of the display with that of the
graphic card. When you experience an unstable or flickering image, use this function
to correct it.
16:9/4:3 (Aspect Ratio)
You can use this function to select your desired aspect ratio.
H.Position (Horizontal Position)
XPress W to move the image left.
XPress X to move the image right.
V.Position (Vertical Position)
XPress W to move the image up.
XPress X to move the image down.
Reset
Choose”Yes” to return the display parameters back to factory default.
™”Reset” returns all settings in Image-I and Image-II to factory defaults.          
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals24
English
User Controls
Video Mode
Image-I
Brightness
Adjusts the brightness of the image.
XPress W to darken the image.
XPress X to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and darkest parts
of the picture. Adjusts the contrast changes the amount of black and white in the
image.
XPress W to decrease the contrast.
XPress X to increase the contrast.
Color
The color setting adjusts a video image from black and white to fully saturated color.
XPress W to decrease the amount of color in the image.
XPress X to increase the amount of color in the image.
Tint
The tint adjusts the color balance of red and green.
XPress W to increase the amount of green in the image.
XPress X to increase the amount of red in the image.
Sharpness
Adjusts the sharpness of the image.
XPress W to decrease the sharpness.
XPress X  to increase the sharpness.
White Segment
Use the white segment control to set the white peaking level of DMD chip. “0”
stands for minimal peaking, and “10” stands for maximum peaking. If you prefer a
stronger image, adjust toward the maximum setting. For a smooth, more natural
image, adjust toward the minimum setting.        
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals25
English
User Controls
Video Mode
Image-II
Keystone
Adjust image distortion caused by tilting the projector. (±16 degrees)
16:9/4:3 (Aspect Ratio)
You can use this function to select your desired aspect ratio.
Zoom
You can use this function to adjust the screen to the most appropriate size or to
enlarge a particular area. You can also use STWX to change the area you want to
enlarge.
Color Temp.
Adjusts the color temperature. The range is from “0” to “4”. The factory default is
“2”.  At  a higher temperature, the image is cooler, at a lower temperature, the image
is warmer.
Reset
Choose “Yes” to return the display parameters back to factory default.
™”Reset” returns all settings in Image-I and Image-II to fatory defaults.          
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals26
English
User Controls
Computer / Video Mode
Language
Language
You can display the multilingual OSD menu. Use S and T to select your preferred
language.        
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals27
English
User Controls
Computer / Video Mode
Management
Menu Location
Choose the Menu location on the display screen.
Projection
X
Front-Desktop
The factory default setting.
X
Rear-Desktop
When you select this function, the projector reverses the image so you can project
behind a translucent screen.
X
Front-Ceiling
When you select this function, the projector turns the image upside down for
ceiling-mounted projection.
X
Rear-Ceiling
When you select this function, the projector reverses and turns the image upside
down at same time. You can project from behind a translucent screen with ceiling
mounted projection.
Lamp Reminding
Choose this function to show or to hide the warning message when the changing
lamp message is displayed.  The message will display up to 30 hours before end of
life.
Lamp Reset
Reset the lamp setting only when the new lamp is replaced.                
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals28
English
Appendices
Troubleshooting
If you experience trouble with the projector, refer to the following.  If the
problem persists, please contact your local reseller or service center.
Problem: No image appears on screen.
XEnsure all the cables and power connections are correctly and  securely connected
as described in the “Installation” section.
XEnsure the pins of connectors are not crooked or broken.
XCheck if the projection lamp has been securely installed. Please refer to the
“Changing the lamp” section.
XMake sure you have removed the lens cap and the projector is switched on.
XIf you are using a Notebook PC:
1. Frist set computer resolution to recommend setting.
2. Switch the Notebook PC display to the “external display only” or “CRT only”
mode.
XIf you experience difficulty change resolutions or your monitor freezes, restart all
the equipment and the projector.      
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals29
English
Appendices
Problem: The screen of the notebook or PowerBook computer
is not displaying your presentation.
XIf you are using Notebook PC:
Some Notebook PCs may deactivate their own monitor’s screen when a second
display device is in use. Each of them has a different way to be reactivated.  Refer
to your computer documentation for detailed information.
XIf you are using an Apple PowerBook:
In Control Panels, open the PowerBook Display to select Video Mirroring “On”.
Problem: Image is unstable or flickering
XUse “Tracking” to correct it.
XChange the monitor color setting from your computer.
Problem: Image has vertical flickering bar
XUse “Frequency” to make an adjustment.
XCheck and reconfigure the display mode of your graphic card to make it compatible
with the product.
Problem: Image is out of focus
XAdjust the Focus Ring on the projector lens.
XMake sure the projection screen is placed witin recommended range of 1.9 to 39.4
feet (0.6 m to 12 meters).      
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals30
English
Appendices
Problem: The image is distorted when displaying 16:9 DVD.
The projector itself will automatically detect 16:9 DVD and adjust the aspect ratio by
digitizating to full screen with 4:3 default setting.
If the image is still distorted, you will also need to adjust the aspect ratio by referring
to the following:
XPlease select 4:3 aspect ratio type on your DVD player if you are playing a 16:9
DVD.
XIf you can select 4:3 aspect ratio type on your DVD player, please select 4:3 OSD
function of the projector for your display.
Problem: Image is reversed.
XOpen “Menu” then select “Management” to adjust the projection.
Problem: Lamp burns out or makes a popping sound
XWhen the lamp reaches its end of life, it will burn out and may make a loud
popping sound.  If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, following the procedures in the
“Changing the Lamp”.