Acer Pd110 Users Guide

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals11
English
Installation
Connecting the Projector
1. VGA Cable
2. Power Cord
3. S-Video Cable
4. Composite Video Cable (optional)
5 USB Cable  (to connect the USB mouse to a PC; optional)
6. HDTV/Component Video Cable (optional)
™To ensure the projector works well with your computer, please set the display
mode on your graphics card to less than or equal to SVGA (800 x 600) resolution.
Also ensure the refresh rate of the graphics card is compatible with the projector.
Refer to the “Compatibility Modes” section on page 34 for more information.
1
5
3
4
6
2
6                        
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals12
English
Installation
Powering On/Off the Projector
Powering On the Projector
1. Remove the lens cap.
2. Ensure that the power cord and signal cable are securely connected.
3. Turn on the lamp by pressing “Power/Standby” on the control panel.\
X
The startup screen will be displayed for 20 seconds and the Power/Standb\
y indicator
will turn solid green.
4. Turn on the source (computer, notebook, or video player, etc.)  The projector will automatically detect your source.
™ If the projector displays “Searching...” please make sure the signal cables
are securely connected.
™If  connecting multiple sources at the same time, use the “Source” button on
the remote control or projector control panel to select the desired input.
Press the “Source” button repeatedly until the desired input is displayed.
™Turn on the projector first and then the computer.
Power/Standby1        
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals13
English
Installation
Powering Off the Projector
1. Press “Power/Standby” to turn off the projector lamp. The projector will display
the message “Power off the lamp?”
2. Press “Power/Standby” again to confirm. Otherwise the message will disappear
after 5 seconds.
3. “Power/Standby” indicator will turn green for approximatly 90 seconds. When
the green light begins flashing, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has
completed the 90-second cooling cycle and has entered standby mode. Once in
standby mode, simply press “Power/Standby” to restart the projector.
4. Disconnect the power cord from the electrical outlet and the projector.
5. Do not turn on the projector immediately following a power off procedure.
™If the “TEMP” indicator begins flashing the projector will display a “Fan
Fail” warning.  After a short period the “Power/Standby” indicator will flash
green for about 90 seconds and the projector will automatically shut itself down.
If this occurs please contact your local reseller or service center.
™If the “TEMP” indicator turns red it indicates the projector has overheated.
The projector will display “Over Temperature. After a short period the
“Power/Standby” indicator will turn green and the projector will
automatically shut itself down.  If this occurs please contact your local
reseller or service center.
™If  the “LAMP” indicator turns red and the “Power/Standby” indicator
turns amber, the projector will automatically shut itself down.  If this occurs
please contact your local reseller or service center.      
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals14
English
Installation
Adjusting the Projected Image
Adjusting the Projector Height
The projector is equipped with an elevator foot for adjusting the projector
height.
To raise the projector:
1. Press the elevator button X.
2. Raise the projector to the desired display angle Y, then release the button to lock
the elevator foot into position.
3. Use Z to fine-tune tilt adjustment.
To lower the projector:
1. Press the elevator button X.
2. Lower the projector then release the button Y to lock the elevator foot into position.
3. Use Z to fine-tune tilt-adjustment.
1Elevator Button
2Elevator Foot
3Elevator fine-tune adjustment        
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals15
English
Installation
Adjusting the Projector Focus
To adjust the focus, simply rotate the focus ring until the image is clear. The projector
will focus at distances from 4.0 feet to 39.4 feet (1.2m to 12m)
Screen29.4” 81.6”133.8” 185.3” 237.5” 289.7”
(Diagonal)
Screen23.5 x 17.7” 65.3 x 48.9” 107.1 x 80.3” 148.2 x 111.2” 190.0 x 142.5” 231.8 x 173.8”
Size (WxH)
Distance4.0’ 11.1’ 18.2’ 25.2’ 32.3’ 39.4’
™ This graph is for reference only.          
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals16
English
User Controls
Panel Control & Remote Control
There are two options for controlling the projector: Remote Control and Panel
Control.
Remote Control
Power / Standby
Refer to the “Power On/Off the Projector” section on page 12-13.
Optimum Setting
XPress “Optimum” to select Conference Mode  or Cinema Mode.
Source
XPress “Source” to cycle between VGA, S-Video, Composite, and Component
sources.Panel Control  Remote Control          
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals17
English
User Controls
Four Directional Selectors
XThese keys are used to control the direction STWX operation on the OSD display.
Page Up (Computer Mode only)
XUse this button to page up. This function is only available when the projector is
connected to a computer via an USB cable.
Page Down (Computer Mode only)
XUse this button to page down. This function is only available when the projector is
connected to a computer via a USB cable.
Menu
XPress “Menu” to launch the OSD menu and press WX
 key to select menu items.
To exit the OSD, press “Menu” again. The projector will automatically save any
changes you made.
Freeze
XPress “Freeze” to pause the screen image.
Keystone + / -
XAdjusts image distortion caused by tilting the projector. (± 16 degrees)
Re-sync
XWhen “Re-sync” is pressed, the projector will automatically synchronize with the
source signal.
Hide
XPressing “Hide” will turn the entire screen black, a useful function for speakers
who require a short pause in order to change their presentation materials.      
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals18
English
User Controls
Use the Panel Control
Power/Standby
XRefer to the ‘Power On/Off the Projector” section on page 12-13.
Source
XPress “Source” to cycle through VGA, S-Video, Composite and Component
sources.
Re-Sync
XAutomatically synchronizes the projector to the input source.
Four Directional Select Keys
XUse
  STWX  to select items or make adjustments for your selection.
Enter
XConfirm your selection of items.
XPress “Menu” to launch the OSD menu and press WX key to select menu items.
To exit the OSD, press “Menu” again. The projector will automatically save any
changes you made.      
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals19
English
User Controls
OSD Menus
How to Operate
XThe projector has a multilingual OSD that allows you to make image adjustments
and change a variety of settings. With a computer source, the OSD displayed is
the “Computer OSD”. With a video source, the OSD displayed is the “Video OSD”.
The projector will automatically detect the source.
XTo launch the OSD menu, press “Menu” on the remote control or panel control.
XWhen the OSD is displayed, press WX key to select main items.
E.g.:Image-ItImage-IItLanguagetManagementtImage-I…
While making selection on a particular page, press “ Menu /  “ key to go into the
sub menu.
XPress STkey to select the required item and adjust the settings by WX key.
When a specified item is selected, the color of the item will change from yellowish
brown to blue.
E.g.:BrightnesstContrasttColor Temp.tZoomtKeystonet
White segmenttBrightness...
XWhen using the WX keys to adjust parameters or select desired sub menu
functions, confirm selections/modifications by pressing “ Menu /  ”  to revert
back to the main menu.  Only the WX keys are enabled now.
XTo exit the OSD, press the “ Menu /  “ button again.      
						

							Downloaded from www.Manualslib.com manuals search engine Downloaded From projector-manual.com Acer Manuals20
English
User’s Info
Edits user preferences by OSD interface. Press Menu to enter Users info.
screen, you can edit as you wish. Edited Users info will display on lower left corner
of the screen when projector is powered ON.
1. Use the WX to select Line1 function, and then press the Menu button. You
can input the character to line one.
2. Use the STWX to select character, and then press Menu to confirm your
selection.
3. Use the WX to select Line2 function, and then press the Menu button. You
can input the character to line two.