Acer Aspire Asx3200 Service Guide
Have a look at the manual Acer Aspire Asx3200 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 213 CPU Feature Security Option When set to system, BIOS will ask for the password each time the system boots up. If set to setup, the password is only required for access into the BIOS setup menus. Setup System MPS Version Control For OS Specifies the version of the Multiprocessor Specification (MPS) that the mainboard will use.1.4 1.1 OS Select For DRAM > 64 MBSelect OS/2 if the system is running OS/2 operating system and the system memory is more than 64 MB in size.Non-OS/2 OS/2 Full Screen Logo Show Enables or disables the display of the full screen boot logo.Enabled Disabled Small Logo (EPA) Show Enables or disables the display of the EPA logo. Disabled Enabled ParameterDescriptionOption Virtualization Select whether to enable or disable the AMD Virtualization Technology (VT) function. VT allows a single platform to run multiple operating systems in independent partitions. Enabled Disabled AMD K8 Cool&Quiet control When set to auto, the AMD Cool’n’Quiet driver dynamically adjust the CPU clock and VIA to reduce heat output from your computer and its power consumption. Disabled Auto ParameterDescriptionOption
14Chapter 2 Hard Disk Boot Priority The Hard Disk Boot Priority submenu allows you to specify the sequence of loading the OS from the installed hard drives. Use the up or down arrow key to select a hard drive, then press the key or the key to move it up or down on the list. l
Chapter 215 Advanced Chipset Features ParameterDescriptionOption Hyper SLI Enable or disable the Scalable Link Interface (SLI) technology.Disabled Enabled iGPU Frame Buffer Control When set to auto, BIOS will automatically setup the frame buffer size. When set to manual, you can set the frame buffer size. Frame buffer size is the total amount of system memory allocated solely for the onboard graphics controller. Auto Manual Frame Buffer Size This parameter can be configured if the iGPU Frame Buffer Control is set to Manual. 64, 16, 32, 128, 256 MB CPU Frequency Sets processor minimum and maximum frequency. 200 Minimum 100 Maximum 500 KBNB HT Speed Controls the physical speed of the processor to the Northbridge HT link.Auto 200, 400, 600, 800 MHz, 1 GHz KBNB HT Width Controls the processor to the Northbridge link bandwidth. Auto Up 8/16 Down 8/16 PCIE Clock Sets the PCI Express clock frequency. 100 Minimum 100 Maximum 200 DRAM Configuration Press Enter to configure memory timing and operation settings. CPU Spread Spectrum Allows you to reduce the EMI of the front side bus by modulating the signals it generates so that the spikes are reduced to flatter curves. Disabled -0.5%, 1.0% PCIE Spread Spectrum Allows you to reduce the EMI of the PCI Express bus by modulating the signals it generates so that the spikes are reduced to flatter curves. When set to down spread, the chipset modulates the PCI Express bus baseline signal downwards by a small amount. When set to disabled, the chipset disables any modulation of the PCI Express bus baseline signal.Disabled Down Spread SATA Spread Spectrum Allows you to reduce the EMI of the SATA bus by modulating the signals it generates so that the spikes are reduced to flatter curves. When set to down spread, the chipset modulates the SATA bus baseline signal downwards by a small amount. When set to disabled, the chipset disables any modulation of the SATA bus baseline signal.Disabled Down Spread
16Chapter 2 iGPU Spread Spectrum Allows you to set the integrated GPU spread spectrum. 50 Triangular Cntr 100/200/300 Triangular Cntr SSE/SSE2 Instructions Enables or disables the processor’s SSE and SSE2 instruction sets. Enabled Disabled MCP78 PCIE Training Cards supporting Gen2 mode will be trained in Gen2 mode. Gen2 if supported Only Gen1 System BIOS cacheable Enables or disables the caching of the mainboard BIOS ROM from F0000h to FFFFFh by the processor’s Level 2 cache. Disabled Enabled ParameterDescriptionOption
Chapter 217 DRAM Configuration ParameterDescriptionOption Timing Mode When set to auto mode, the system reads the electronic data sheet of the memory modules and adjusts the timings accordingly. When set to MaxMemClk, you can manually specify the memory clock frequency independent of the system bus frequency. Auto MaxMemClk Memory Clock value or Limit Displays the current memory clock frequency. CKE base power down modeAll synchronous memory devices can go into sleep mode as soon as the clock enable (CKE) signal is disasserted. In that case, the internal clocks are disabled and the memory chip goes into auto-refresh mode which is the lowest power state at which the memory retains data. If then power is turned off, the device will lose all data, however, as long as standby power is maintained, no data loss will occur. Disabled Enabled CKE based power down Sets the CKE power saving through disasserting clock enable using system level or per channel basis. Per Channel Per CS Memclock tri-stating Enables or disables the memory clock tri-stating during C3 an Alt VD feature. Disabled Memclock tri- stating during C3 and Alt VD Memory Hole Remapping Enables or disables memory remapping around the memory hole. Enabled Disabled Auto Optimize Bottom IO Allows you to auto optimize maximal memory size when kernel assigns PCI Resources.Enabled Disabled Bottom of UMA DRAM [31:24] [FC]Allows you to enter a HEX number ranging from 0000 to 00F0. Minimim 0000 Maximum 00FC
18Chapter 2 Integrated Peripherals ParameterDescriptionOption IDE Function Setup Press Enter to access the IDE Function Setup submenu. MCP Storage Config Press Enter to access the MCP Storage Config submenu. Init Display First Select whether to boot the system using the AGP graphic card or a PCI card installed on the PCI Express slot or PCI slot.PCIEx PCI Slot Onboard HD Audio Enables or disables the onboard audio controller. Auto Disabled HDMI Audio Allows you to control the audio function of the onboard HDMI. Disabled Auto MAC LAN Enables or disables the built-in network interface card. Auto Disabled IDE HDD Block Mode When enabled, the BIOS will automatically detect if your hard disk supports block transfers and set the proper block transfer settings for it. Depending on the IDE controller, up to 64 KB of data can be transferred per interrupt when block transfers are enabled. When disabled, only 512 bytes of data can be transferred per interrupt.Enabled Disabled Onboard Serial Port 1 Select the I/O address and IRQ for the first serial port. 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto Disabled Onboard Parallel Port Select the I/O address and IRQ for the onboard parallel port.378/IRQ7 278/IRQ5 3BC/IRQ7 Disabled Parallel Port Mode Select an operating mode for the onboard parallel port. SPP EPP ECP ECP+EPP ECPM Mode Use DMA Select DMA channel for the LPT port in ECP mode. This parameter can be configured if the parallel port mode is set to ECP or ECP +EPP mode. 3 1 USB Device Setting Press Enter to access the USB Device Setting submenu.
Chapter 219 IDE Function Setup ParameterDescriptionOption OnChip IDE Channel 0 Enables or disables the first IDE channel. Enabled Disabled Primary Master PIO When set to Auto, BIOS setup automatically detects if the installed hard disk supports the function. If supported, it allows for faster data recovery and read/write timing that reduces hard disk activity time. This results in better hard disk performance. Mode 0 to 4 provide progressive increase of performance.Auto Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Primary Slave PIOAuto Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 Primary Master UDMA Enables or disables the primary and master UDMA modeAuto Disabled Primary Slave UDMAAuto Disabled IDE DMA Transfer Enables or disables DMA (Direct Memory Access) transfers for all IDE drives.Enabled Disabled Serial-ATA Controller Enables or disables the serial ATA controller. Enabled Disabled IDE Prefetch Mode Enables or disables the IDE controller to prefetch data from the IDE drive. Enabled Disabled
20Chapter 2 MCP Storage Config ParameterDescriptionOption SATA Operation Mode Select a SATA operation mode. AHCI IDE RAID Linux AHCI SATA 0 -- Port 1 ~ 6 Enables or disables the SATA RAID on ports 1 to 6. This parameter can be configured if the SATA Operation Mode is set to RAIDDisabled Enabled SATA SALP Feature Select a Supports Aggressive Link Power Management (SALP) feature. Off Partial Slumber
Chapter 221 USB Device Setting ParameterDescriptionOption USB 1.0 Controller Enables or disables the onboard USB controller. Enabled Disabled USB 2.0 ControllerEnabled Disabled USB Operation Mode Select a USB device operation speed.High Speed Full Low Speed USB Keyboard Function Enables or disables legacy support of the USB keyboard. Enabled Disabled USB Mouse Function Enables or disables legacy support of the USB mouse. Enabled Disabled USB Storage Function Enables or disables legacy support of the USB storage device. Enabled Disabled
22Chapter 2 Power Management Setup ParameterDescriptionOption ACPI function Enables or disables the Advanced Configuration and Power Management (ACPI) function. Enabled Disabled ACPI Suspend Type Select an ACPI state.S1 & S3 S1 (POS) S3 (STR) Power Management Select a power saving method for the following modes: • HDD power down • Suspend modeUser Define Min. Saving Max Saving Video Off Method Determines the manner when the monitor goes blank.DPMS Support Blank Screen V/H Sync + Blank HDD Power Down Set a time when the hard disk drives will power down after a period inactivity. Disabled 1 to 14 Min HDD Down in Suspend Enables or disables the HDD power down function in suspend mode. Disabled Enabled Soft-Off by PBTN Determines the behavior of system power button. Instant-Off Delay 4 Sec PowerOn After Pwr-Fail Set the system to automatically start itself up after a power failure. Off On Former-Sts WOL (PME#)/From Soft-Off Enables or disables to wake up the system from a power saving mode through an event on a LAN device or using soft-off.Disabled Enabled S5 Resume by USB If enabled, press any key or click the mouse will wake system from S1/ S3 state.Disabled Enabled Power-On by Alarm Enables or disables to boot the system on scheduled date/time.Disabled Enabled Day of Month Alarm This parameter can be configured if the Power-On by Alarm is set to enable. Time (hh:mm:ss) Alarm HPET Support Enables or disables the High Precision Event Timer (HPET) function. Enabled Disabled PS2 KB Wakeup Enables or disables to wake up the system from a power saving mode using a PS2 keyboard. Disabled Enabled PS2 Mouse Wakeup Enables or disables to wake up the system from a power saving mode using a PS2 mouse. Disabled Enabled