Acer Aspire 9510 Service Guide

							Chapter 375
25. Remove the two screws securing the fan2.
26. Disconnect the fan2 connector from the mainboard and remove the fan2.
27. Release the three attached screws securing the VGA heatsink.
28. Remove the VGA heatsink.
29.Remove the three attached screws and remove the screw securing the CPU heatsink.
30.Remove the CPU heatsink.
31.Remove the two screws securing the VGA card.
32.Remove the VGA card.
33.Remove the screw securing the VGA bracket.
34.Remove the VGA bracket.
35.Turn the screw counterclockwise with a flat screw driver to release the CPU. 
						

							76Chapter 3
36.Remove the CPU as shown.
37.Remove the TV cable. 
						

							Chapter 377
LCD Disassembly
1.Remove the eight LCD screw pads.
2.Remove the eight screws securing the LCD bezel.
3.Remove the LCD bezel.
4.Remove the screw securing the inverter board.
5.Turn the inverter board over, disconnect the LVDS cable and LCD cable from the inverter board.
6.Remove the inverter board.
7.Remove the four screws securing the LCD panel and LCD hinge.
8.Lift up the LCD panel, tear off the tape on the LCD cable and disconnect the LCD cable. 
9.Remove the LCD panel.
10.Remove the four screws securing the left LCD bracket. 
						

							78Chapter 3
11 .Remove the left LCD bracket.
12.Remove the four screws securing the right LCD bracket.
13.Remove the right LCD bracket.
14.Release the spring and remove the left and the right latches from the LCD cover.
15.Remove the screw securing the CCD module.
16.Remove the CCD module from the LCD cover.
17.Remove the left and right LCD hinge.
18.Remove the two screws securing the antenna bracket.
19.Remove the antenna from the LCD cover. 
						

							Chapter 379
CCD Module Disassembly
1.Pull out the CAS from the CCD module.
2.Remove the CCD holder from the CCD module.
3.Open the CCD module as shown.
4.Remove the two screws securing the CCD board.
5.Remove the CCD hinge.
6.Remove the CCD board.
7.Disconnect the CCD cable from the CCD board. 
						

							80Chapter 3
HDD Disassembly 
1.Remove the four screws securing the 2nd HDD bracket.
2.Remove the 2
nd HDD bracket.
3.Remove the four screws securing the 1
st HDD bracket.
4.Remove the 1
st HDD bracket. 
						

							Chapter 381
ODD Disassembly
1.Remove the ODD bezel from the ODD module.
2.Remove the two screws securing ODD bracket.
3.Remove the ODD bracket from the ODD module. 
						

							Chapter 482
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model.  Non-Acer products, prototype cards, or modified 
options can give false errors and invalid system responses.
1.Duplicate symptom and obtain the failing symptoms in as much detail as possible.
2.Distinguish symptom. Verify the symptoms by attempting to re-create the failure by running the diagnostic 
test or by repeating the same operation.
3.Disassemble and assemble the unit without any power sources.
4.If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You 
can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
5.Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)Go To
Power failure. (The power indicator does not go 
on or stay on.)“Power System Check” on page 84.
POST does not complete. No beep or error 
codes are indicated.“Power-On Self-Test (POST) Error Message” on 
page 86
“Undetermined Problems” on page 98
POST detects an error and displayed messages 
on screen.“Error Message List” on page 87
Other symptoms (i.e. LCD display problems or 
others).“Power-On Self-Test (POST) Error Message” on 
page 86
Symptoms cannot be re-created (intermittent 
problems).Use the customer-reported symptoms and go to 
“Power-On Self-Test (POST) Error Message” on 
page 86
“Intermittent Problems” on page 97
“Undetermined Problems” on page 98
Troubleshooting
Chapter 4 
						

							83Chapter 4
System Check Procedures
External Diskette Drive Check
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.Reconnect the external diskette drive/DVD-ROM module.
2.Replace the external diskette drive/CD-ROM module.
3.Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does 
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.Boot from the diagnostics diskette and start the diagnostics program.
2.See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.Reconnect the external diskette drive/CD-ROM module.
2.Replace the external diskette drive/CD-ROM module.
3.Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable 
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a 
non-defective FRU:
1.Reconnect the keyboard cables.
2.Replace the keyboard.
3.Replace the main board.
The following auxiliary input devices are supported by this computer:
TNumeric keypad
TExternal keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation. 
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.Go to the diagnostic memory in the test items.
3.Press F2 in the test items.
4.Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error. 
						

							Chapter 484
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.Remove the battery pack.
2.Connect the power adapter and check that power is supplied.
3.Disconnect the power adapter and install the charged battery pack; then check that power is supplied by 
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T“Check the Battery Pack” on page 85