Acer Aspire 8935g Service Guide

Chapter 371
Main Unit Disassembly Process
Upper Cover Disassembly Flowchart
Screw List
StepScrewQuantityPart No.
Switch Cover M2.5*6.5 9 86.ARE07.001
M2.5*4 4 86.D01V7.001
Power Board M2.5*4 3 86.D01V7.001
LCD Module M2.5*6.5 4 86.ARE07.001
Upper Cover M2.5*6.5 9 86.ARE07.001
M2.5*4 5 86.D01V7.001
M2*3 1 86.S0207.001
Rem ove
Switch Cover
Rem ove
LCD Module
Rem ove
Media Board
Remove External
Modules before
proceeding
Upper Cover
Rem ove
Launch BoardRem ove
Volume Control
BoardRem ove
Finger Print
Reader...

72Chapter 3
Lower Cover Disassembly Flowchart
Screw List
StepScrewQuantityPart No.
Bluetooth Board M2*3 1 86.S0207.001
USB Board M2.5*4 1 86.D01V7.001
Power Saving Board M2.5*4 1 86.D01V7.001
Mainboard M2.5*4 3 86.D01V7.001
Kensington Lock 
BracketM2*3 1 86.S0207.001
Subwoofer 4
Hinge Supports M2.5*4 6 86.D01V7.001
Speaker Module 6
Graphics Card 
HeatsinkM2.5*6.5 2 86.ARE07.001
Graphics Card M2.5*6.5 1 86.ARE07.001
Rem ove
Graphics Card
Rem ove
Mainboard
Rem ove
USB Board
Rem ove
Upper Cover
Remove...

Chapter 373
Removing the Keyboard
1.See “Removing the Battery Pack” on page 56.
2.Press the six securing clips inward to release the Keyboard from the Upper Cover.
3.Lift the centre of Keyboard up as shown.
IMPORTANT: Do not remove the Keyboard from the computer; the Keyboard FFCs are still connected.
4.Turn the Keyboard over and place it on the TouchPad area to expose the FFC cables. 

74Chapter 3
5.Disconnect the Backlight cable by opening the FFC latch and removing the cable from the Mainboard.
6.Disconnect the Keyboard cable by opening the FFC latch and removing the cable from the Mainboard.
7.Remove the Keyboard from the Upper Cover. 

Chapter 375
Removing the Switch Cover
1.See “Removing the Battery Pack” on page 56.
2.Turn the computer over. Remove the thirteen screws securing the Switch Cover to the Upper Cover.
IMPORTANT: Do not lift the Switch Cover away from the computer; the Power Board FFC is still connected.
3.Turn the computer over and open the LCD Panel. Lift the Switch Cover, rear edge first, as shown.
StepSizeQuantityScrew Type
Switch Cover
(red callout)M2.5*6.5 9
Switch Cover
(green callout)M2.5*4 4 

76Chapter 3
4.Turn the Switch Cover over and place it face down on the Keyboard.
5.Open the Power Board FFC locking latch and disconnect the FFC from the Mainboard.
6.Remove the Switch Cover from the Upper Cover. 

Chapter 377
Removing the Power Board
1.See “Removing the Switch Cover” on page 75.
2.Open the Power Board FFC locking latch and disconnect the FFC from the Power Board.
3.Remove the three screws securing the Power Board to the Switch Cover.
4.Lift the Power Board away from the Switch Cover right side first to release the securing clip.
StepSizeQuantityScrew Type
Power Board M2.5*4 3 

78Chapter 3
Removing the LCD Module
1.See “Removing the Switch Cover” on page 75.
2.Turn the computer over and ensure that the Antenna cables are free from obstructions.
3.Pull the Antenna cables through the Upper Cover as shown. Ensure that the Antennas are completely free 
from the cover.
4.Remove the Antenna from the cable channel all the way to the Hinge Well. Ensure that the cables are free from 
all cable clips. 

Chapter 379
5.Grasp the pull tab and lift upward as shown to disconnect the LVDS cable.
6.Remove the LVDS cable from the cable channel all the way to the Hinge Well. Ensure that the cable is free 
from all cable clips.
7.Disconnect the MIcrophone cable from the Mainboard. 

80Chapter 3
8.Remove the Microphone cable from the cable channel all the way to the Hinge Well. Ensure that the cable is 
free from all cable clips.
9.Remove the four screws securing the LCD Module to the Lower Cover.
10.Using both hands, lift the LCD Module clear of the Lower Cover.
StepSizeQuantityScrew Type
LCD Module M2.5*6.5 4