Acer Aspire 6530 User Manual

							Chapter 231
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press Enter.
3.Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields. 
The computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility. 
						

							32Chapter 2
Changing a Password
1.Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The 
Set Password box appears.
2.Type the current password in the Enter Current Password field and press Enter.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses Enter.
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following 
message. 
						

							Chapter 233
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.
Information     Main     Sec urityBootExit
Item Specific Help
B oot priority  order:
    1: IDE 0: TOSHIBA  MK3252GSX-(S1)K ey s  us ed to view or
    2: IDE 1: S T9160310AS -(S2)c onfigure devic es :
    3: IDE CDROM: Optiarc  DVD RW  AD-7560S -(PUp and Down arrows
    4: PCI LAN: Atheros  B oot Agents elec t a devic e.
    5: US B  HDD:
    6: USB FDD:< F6>  and < F5>  moves
    7: USB KEY:the devic e up or down.
    8: US B  CDROM :
E x c luded from boot order:< x >  ex c lude or inc lude
the device to boot.
F1 Help           
↑↓ Select Item           F5/F6 Change V alues             F9 Setup Defaults
ESC Exit         
←→ Select Menu       Enter Select
XS ub-Menu      F10 Save and E x it Phoenix BIOS  S etup Utility 
						

							34Chapter 2
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding 
ChangesExit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
Informat ion     Main     Sec urit y BootExit
Item Specific Help
Ex it  Saving Changes
Ex it  Dis c arding ChangesEx it  Sy s t em Set up and
Load Set up Default ssave your changes to
Dis c ard ChangesCMOS .
Save Changes
F1 Help           
↑↓ Select Item           F5/F6 Change Values             F9 Set up Default s
ESC Exit         
←→ Selec t  Menu       Enter Select
XSub-Menu      F10 Save and Exit PhoenixBIOS Setup Utility 
						

							Chapter 235
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
•New versions of system programs
•New features or options
•Restore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: Create a Crisis Recovery Media (such as USB HDD) before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not 
contain enough power to finish BIOS flash, the system will not boot as the BIOS is not loaded. 
Perform the following steps to use the Flash Utility:
1.Press F2 during boot to enter the Setup Menu.
2.Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move 
USB HDD to position 1.
3.Execute the IFLASH.BAT batch file to update BIOS (Read xxxxx.fd to Memory).
Information     Main     Sec urityBootExit
Item Spec ific  Help
B oot priority  order:
    1: US B  HDD: A B CK ey s  us ed to view or
    2: IDE 0: TOSHIBA  MK3252GSX-(S1)c onfigure devic es :
    3: IDE 1: S T9160310AS -(S2)Up and Down arrows
    4: IDE CDROM: Optiarc  DVD RW  AD-7560S -(Ps elec t a devic e.
    5: PCI LAN: Atheros  B oot Agent
    6: USB FDD:< F6>  and < F5>  moves
    7: USB FDD:the devic e up or down.
    8: USB KEY:
E x c luded from boot order:< x >  ex c lude or inc lude
the de ic e to boot
Phoenix BIOS  S etup Utility 
						

							36Chapter 2
4.In flash BIOS, the message Please do not remove AC Power Source displays.
NOTE: If the AC power is not connected, the following message displays.
Plug in the AC power to continue.
5.Flash is complete when the following message displays. 
6.Shutdown or reboot base on iflash.bat command. 
						

							Chapter 237
Remove HDD/BIOS Utility
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
•If you key in wrong HDD password three times, Hdd password error code displays. See the image 
below.
To reset the HDD password, run HDD_PW.EXE as follows:
1.
Key in hdd_pw 15494 0 
2.Press 2.
3.Select one upper-case string from the list.
4.Reboot system and key in the selected string (0KJFN42 or UVEIQ96) on the HDD User 
Password screen. 
						

							38Chapter 2
Remove BIOS Password:
If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the 
image below.
To reset the BIOS password, run BIOS_PW.EXE as follows:
1.
Key in bios_pw 14452 0
2.Select one string from the list. 
						

							Chapter 239
3.Reboot the system and key in the selected string (qjjg9vy, 07yqmjd etc.) for the BIOS user 
password. 
						

							40Chapter 2