Acer Aspire 5735z Service Guide

Chapter 351
Removing the SD dummy card
1.Push the SD dummy card all the way in to eject it.
2.Pull it out from the slot. 
Removing the ExpressCard dummy card
1.Push the ExpressCard dummy card all the way in to eject it.  

52Chapter 3
2.Pull it out from the slot.
Removing the Lower Cover
1.See “Removing the Battery Pack” on page 50.
2.Remove the four captive screws and the six screws (A) on the lower cover.   
StepSize (Quantity)ColorTo r q u e
1~6 M2.5 x L8 (6) Black 3.0 kgf-cm 

Chapter 353
3.Use a plastic screw driver to carefully pry open the lower cover. 
4.Remove the lower cover from the lower case. 
Removing the DIMM 
1.See “Removing the Battery Pack” on page 50.
2.See “Removing the Lower Cover” on page 52..
3.Push out the latches on both sides of the DIMM socket to release the DIMM.  

54Chapter 3
4.Remove the DIMM module. 
Removing the WLAN Board Modules
1.See “Removing the Battery Pack” on page 50.
2.See “Removing the Lower Cover” on page 52.
3.Remove the white antenna cable that is taped to the WLAN board module. 

Chapter 355
4.Disconnect the antenna cables from the WLAN board. 
NOTE: There are 2 antenna cables connected to the WLAN board module. The Black antenna cable is 
connected to the MAIN connector and the Gray antenna cable is connected to the AUX connector.
5.Move the antenna away from the WLAN board and remove the one screw (H) on the WLAN board to 
release the WLAN board.   
StepSize (Quantity)ColorTo r q u e
1 M2 x L3 (1) Black 1.6 kgf-cm 

56Chapter 3
6.Detach the WLAN board from the WLAN socket. 
NOTE:  When attaching the antenna back to the WLAN board, make sure the cable are arranged properly. 
Removing the Hard Disk Drive Module 
1.See “Removing the Battery Pack” on page 50.
2.See “Removing the Lower Cover” on page 52.
3.Remove the one screw (C) securing the hard disk drive module. 
StepSize (Quantity)ColorTo r q u e
1 M2 x L3 (1) Silver 1.6 kgf-cm 

Chapter 357
4.Slide the hard disk drive module away from the connector. 
5.Lift the hard disk drive module and remove it from the hard disk drive bay.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 
6.Remove the two adhesive tape covering the two screws. 

58Chapter 3
7.Remove the two screws (D) securing the hard disk to the bracket and remove the hard disk from the 
bracket.     
Removing the Optical Drive Module
1.See “Removing the Battery Pack” on page 50.
2.See “Removing the Lower Cover” on page 52.
StepSize (Quantity)ColorTo r q u e
1~2 M3 x L4 (2) Silver 3.0 kgf-cm 

Chapter 359
3.Use a pin and push it inside the emergency eject hole to eject the odd drive tray.
4.Carefully pull out the odd drive tray until the part of the module is visible and then slowly push back to 
close the tray into the module with the module still partially exposed. 
5.Slowly pull out the odd module from the odd drive bay.  

60Chapter 3
6.Remove the two screws (C) securing the locker bracket and remove the locker bracket from the optical 
disk drive module.   
StepSize (Quantity)ColorTo r q u e
1~2 M2 x L3 (2) Silver 1.6 kgf-cm