Acer Aspire 5735z Service Guide

Chapter 131
Battery Type Li-ion
Pack capacity  6Cell 4400 MAH/8Cell 4800 MAH
Number of battery cell 6/8
Package configuration 3 cells in series, 2 series in parallel
4 cells in series, 2 series in parallel
LCD 15.4” inch
ItemSpecification
Vendor & model name CMO/AUO/LG
Screen Diagonal (mm) 15.4 inches
Display resolution (pixels) 1280 x 800 WXGA
Pixel Pitch 0.204 x 0.204
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
Typical White Luminance (NIT)
also called Brightness220
Luminance...

32Chapter 1
Suspend to RAM (S3) CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4) Also called Hibernation Mode. System saves all system 
states and data onto the disc prior to power off the whole 
system. System Power Management
ACPI modePower Management 

Chapter 233
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if 
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press  to enter Setup” message is prompted 
on the...

34Chapter 2
Navigating the BIOS Utility
There are five menu options: Information, Main, Security, Boot, and Exit.
Follow these instructions:
qTo choose a menu, use the left and right arrow keys.
qTo choose an item, use the up and down arrow keys.
qTo change the value of a parameter, press F5 or F6.
qA plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
qPress Esc while you are in any of the menu options to go to the Exit menu.
qIn any menu, you can load default settings by...

Chapter 235
Information
The Information screen displays a summary of your computer hardware information.
NOTE: The system information is subject to different models.
ParameterDescription
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
IDE0 Model Name This field shows the model name of HDD installed on primary IDE master.
IDE0 Serial Number This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name This...

36Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option 
and recovery.
NOTE: The screen above is for your reference only. Actual values may differ.
Phoenix   SecureCore(tm)   Setup   Utility
Main
Item   Specific   Help
,   ,   or
   selects   field. System Time:
System   Date:
System   Memory:
Extended   Memory:
Video   Memory:
Quiet   Boot:
Network   Boot:
F12   Boot   Menu:
D2D   Recovery:
SATAMode
F1
EscHelp
ExitSelect    Item
Select...

Chapter 237
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is 
because the user is not allowed to control the settings in these cases.
ParameterDescriptionFormat/Option
System Time Sets the system time. The hours are displayed 
with 24-hour format.Format: HH:MM:SS 
(hour:minute:second) System Time
System Date Sets...

38Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized 
use.
NOTE: Please refer to “Remove HDD/BIOS Password” section if you need to know how to remove HDD/BIOS 
Password.
Phoenix SecureCore(tm) Setup Utility
Main
F1
EscHelp
ExitSelect Item
Select Menu
Change Values
Select Sub-Menu -/+
EnterF9
F10Setup Defaults
Save and Exit
Information Security Boot Exit
Item Specific Help
Supervisor Password
controls access of the
whole setup...

Chapter 239
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the “w” and “y” keys to highlight the Set...

40Chapter 2
Removing a Password
Follow these steps:
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set 
Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The 
computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press u to save the changes and exit the BIOS...