Acer Aspire 5610 Service Guide

							Chapter 241
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is 
because the user is not allowed to control the settings in these cases.
ParameterDescriptionFormat/Option
System Time Sets the system time. The hours are displayed 
with 24-hour format.Format: HH:MM:SS 
(hour:minute:second) System Time
System Date Sets the system date. Format MM/DD/YYYY (month/day/
year)
System Date
System Memory This field reports the memory size of the system. 
Memory size is fixed to 640MB
Extended Memory This field reports the memory size of the 
extended memory in the system. 
Extended Memory size=Total memory size-1MB
VGA Memory Shows the VGA memory size. VGA Memory 
size=64/128MB
Quiet Boot Determines if Customer Logo will be displayed or 
not; shows Summary Screen is disabled or 
enabled. 
Enabled: Customer Logo is displayed, and 
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and 
Summary Screen is enabled. Option: 
Enabled or Disabled
Power on display Auto: During power process, the system will 
detect if any display device is connected on 
external video port. If any external display device 
is connected, the power on display will be in CRT 
(or projector) only mode. Otherwise it will be in 
LCD only mode.
Both: Simultaneously enable both the integrated 
LCD screen and the system’s external video port 
(for an external CRT or projector).Option: 
Auto or Both
Network Boot Enables, disables the system boot from LAN 
(remote server).Option: 
Enabled or Disabled
F12 Boot Menu Enables, disables Boot Menu during POST.
Option: 
Disabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The 
function allows the user to create a hidden 
partition on hard disc drive to store operation 
system and restore the system to factory 
defaults.Option: 
Enabled or Disabled 
						

							42Chapter 2
Advanced
The Advanced screen contains parameters involving your hardware devices. It also provides advanced
 settings of the system.
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
 parameter settings.
DescriptionOption
Infrared Port  Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled 
by OSDisabled
Enabled
Auto
PhoenixBIOS Setup Utility 
   Information        Main        Advanced      Security       Boot       Exit 
 
  
Item Specific Help 
  
 
  
  
Infrared Port (FIR)
 
  
 
Configure Infrared Port 
using options: 
 
  [Disable]
    No configuration
[Enabled]
    User configuration 
 
 
    
 
 
    
    
 
 
    
   
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub-Menu      F10 Save and Exit  
 
  
  [Enabled] 
						

							Chapter 243
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized 
use.
PhoenixBIOS Setup Utility 
     Information             Main         AdvancedBoot
 
 
Item Specific Help 
Supervisor Password Is : Clear 
User Password Is :
HDD Password Is:Clear
Clear
Set Supervisor Password
Set User Password
Set Hdd Password
  
Password on Boot[Disabled]
 
  
 
Supervisor Password 
controls accesses of the 
whole setup utility. 
It can be used to 
boot up when Password 
on boot is enabled. 
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub-Menu      F10 Save and Exit  
[Enter]
[Enter]
[Enter]Exit
Security 
						

							44Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested 
parameter settings.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget 
your password. If you forget your password, you may have to return your notebook computer to your 
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Supervisor Password box appears:
2.Type a password in the “Enter New Password” field. The password length can not exceeds 8 
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New 
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.Press e.
                After setting the password, the computer sets the User Password parameter to “Set”.
4.If desired, you can opt to enable the Password on boot parameter.
5.When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
ParameterDescriptionOption
User Password is Shows the setting of the user password.
Clear or Set
Supervisor Password is Shows the setting of the Supervisor password
Clear or Set
Set User Password Press Enter to set the user password. When 
user password is set, this password protects 
the BIOS Setup Utility from unauthorized 
access. The user can enter Setup menu only 
and does not have right to change the value of 
parameters.
Set Supervisor Password Press Enter to set the supervisor password. 
When set, this password protects the BIOS 
Setup Utility from unauthorized access. The 
user can not either enter the Setup menu nor 
change the value of parameters.
Primary HardDisk Security Enables or disables primary hard disk security 
function. 
Password on Boot Defines whether a password is required or not 
while the events defined in this group 
happened. The following sub-options are all 
requires the Supervisor password for changes 
and should be grayed out if the user password 
was used to enter setup.
Disabled or Enabled 
						

							Chapter 245
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Press e twice without typing anything in the Enter New Password and Confirm New Password fields. 
The computer then sets the Supervisor Password parameter to “Clear”.
4.When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The 
Set Password box appears:
2.Type the current password in the Enter Current Password field and press e.
3.Type a password in the Enter New Password field. Retype the password in the Confirm New Password 
field.
4.Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.If desired, you can enable the Password on boot parameter.
6.When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following. 
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the 
Setup Warning. 
						

							46Chapter 2
If the new password and confirm new password strings do not match, the screen will display the following 
message. 
						

							Chapter 247
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices 
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility 
    Information       Main       Advanced       Security        Exit 
 
  
Item Specific Help 
  
   
 
 
 Use <
↑> or  to select a device
devices, then press  to
move it up the list, or  to
move it down the list. Press
 to escape the menu.
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub -Menu      F10 Save and Exit  
Boot
Boot priority order:
      1:   IDE 0:            TOSHIBA MK6025GAS-(PM)
      2:   IDE 1:            MATSHITADVD-RAM UJ-845S
      3:   IDE 2: 
      4:   USB  FDD: 
      5:   PCI  LAN:      Broadcom MBA
      6:   USB  HDD:
      7:   USB  KEY:
      8:   USB  CDROM:    
						

							48Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
ParameterDescription
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
PhoenixBIOS Setup Utility 
  Information         Main             Advanced          Security             Boot
 
  
Item Specific Help 
Exit Saving Changes  
Exit Disarding Changes   
Load Setup Defaults 
 
 Exit System Setup and save 
your changes to CMOS.
 
F1  Help       ↑↓ Select Item          F5/F6 Change Values             F9 Setup Defaults 
Esc Exit        ← →  Select Menu      Enter  Select   4Sub -Menu      F10 Save and Exit  
Discard ChangesExit
Save Changes 
						

							Chapter 249
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
TNew versions of system programs
TNew features or options
TRestore a BIOS when it becomes corrupted. 
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not 
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
completely loaded. 
Fellow the steps below to run the Phlash:
First, you have to create a crisis diskette. Follow the steps to create a crisis diskette.
1.Insert a floppy disk to the notebook under Windows mode.
2.Execute “wincris.exe”
3.Wait for few minutes. The process will completed automatically.
After you have created crisis diskette, you can then recovery the fail system.
1.Insert the Crisis diskette to the computer.
2.Press Fn+Esc and power on the sytem.
3.The systme will execute the file automatically. Wait for few minutes the system will reboot as the entire 
process completed. 
						

							50Chapter 2