Acer Aspire 5610 Service Guide
Have a look at the manual Acer Aspire 5610 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 481 Battery can’t be charged See “Check the Battery Pack” on page 71. Battery pack System board PCMCIA-Related Symptoms Symptom / ErrorAction in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly System board PCMCIA slot pin is damaged. PCMCIA slot assembly Memory-Related Symptoms Symptom / ErrorAction in Sequence Memory count (size) appears different from actual size.Enter BIOS Setup Utility to execute “Load Default Settings, then reboot system. DIMM System board Speaker-Related Symptoms Symptom / ErrorAction in Sequence In Windows, multimedia programs, no sound comes from the computer. Audio driver Speaker System board Internal speakers make noise or emit no sound. Speaker System board Power Management-Related Symptoms Symptom / ErrorAction in Sequence The system will not enter hibernation See “Save to Disk (S4)” on page 39. Keyboard (if control is from the keyboard) Hard disk drive System board The system doesnt enter hibernation mode and four short beeps every minute.Press Fn+ oand see if the computer enters hibernation mode. Touchpad Keyboard Hard disk connection board Hard disk drive System board The system doesn’t enter standby mode after closing the LCDSee “Save to Disk (S4)” on page 39. LCD cover switch System board The system doesnt resume from hibernation mode.See “Save to Disk (S4)” on page 39. Hard disk connection board Hard disk drive System board The system doesnt resume from standby mode after opening the LCD.See “Save to Disk (S4)” on page 39. LCD cover switch System board Power-Related Symptoms Symptom / ErrorAction in Sequence
82Chapter 4 NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined Problems” on page 84. Battery fuel gauge in Windows doesn’t go higher than 90%. Remove battery pack and let it cool for 2 hours. Refresh battery (continue use battery until power off, then charge battery). Battery pack System board System hangs intermittently. Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / ErrorAction in Sequence System configuration does not match the installed devices. Enter BIOS Setup Utility to execute “Load Default Settings”, then reboot system. Reconnect hard disk/CD-ROM/diskette drives. External display does not work correctly. Press Fn+F5, LCD/CRT/Both display switching System board USB does not work correctly System board Print problems. Ensure the “Parallel Port” in the “Onboard Devices Configuration” of BIOS Setup Utility is set to Enabled. Onboard Devices Configuration Run printer self-test. Printer driver Printer cable Printer System Board Serial or parallel port device problems. Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup Utility is set to Enabled. Device driver Device cable Device System board Keyboard/Touchpad-Related Symptoms Symptom / ErrorAction in Sequence Keyboard (one or more keys) does not work. Reconnect the keyboard cable. Keyboard System board Touchpad does not work. Reconnect touchpad cable. Touchpad board System board Modem-Related Symptoms Symptom / ErrorAction in Sequence Internal modem does not work correctly. Modem phone port modem combo board System board Power Management-Related Symptoms Symptom / ErrorAction in Sequence
Chapter 483 Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1.Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2.If no error is detected, do not replace any FRU. 3.If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
84Chapter 4 Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 69.): 1.Power-off the computer. 2.Visually check them for damage. If any problems are found, replace the FRU. 3.Remove or disconnect all of the following devices: TNon-Acer devices TPrinter, mouse, and other external devices TBattery pack THard disk drive TDIMM TCD-ROM/Diskette drive Module TPC Cards 4.Power-on the computer. 5.Determine if the problem has changed. 6.If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7.If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU: TSystem board TLCD assembly
Chapter 585 Board Layout Top View 1 JP1 LCD Connector 10 SW7 Touchpad Down Button 2 SW1 Lid Switch 11 SW2 Touchpad Up Button 3 JP3 MDC Connector 12 SW5 Touchpad Left Button 4 JP2 Power Button Connector 13 SW3 Touchapd Left Button 5 JP6 Media Board Connector 14 JP13 Internal Microphone Connector 6 JP7 Touchpad Board Connector 15 JP12 Internal Speaker Connector 7 JP43 SIM Card Connector 16 JP9 PCMCIA Socket 8 SW4 Touchpad Right Button 17 IR1 FIR Module 9 SW6 Touchpad Left Button 18 JP8 Internal Keyboard Connector Jumper and Connector Locations Chapter 5
86Chapter 5 Bottom View NOTE: This is engineering sample. The image above may not be exactly the same as the real main board you get. 1 JP19 FAN Connector 17 JP40 Headphone/SPDIF Jack 2 U42 VGA Chipset 18 JP41 Line-In Jack 3 JP18 CPU Socket 19 JP42 Microphone-in Jack 4 JP16 DVI Connector 20 IR2 CIR Module 5 JP15 CRT Connector 21 SW8 Wireless LAN Switch 6 JP14 TV-Out Connector 22 SW9 Bluetooth and 3G Switch 7 PCN1 DC-IN Jack 23 U48 South Bridge Chipset 8 JP17 Mini Card Connector 24 JP30 Mini Card Connector 9 JP22 DDRII so-DIMM Socket 25 JP29 IEEE 1394 Connector 10 JP21 DDRII so-DIMM Socket 26 JP27 5 IN1 Socket 11 J3 Clear CMOS Jumper 27 JP23 RJ45 Connector 12 JP24 ODD Connector 28 JP5 USB Connector 13 PJP1 Battery Connector 29 JP4 USB Connector 14 JP32 HDD Connector (SATA) 30 JP28 MINIPCI Connector (TV-Tuner) 15 JP33 HDD Connector (PATA) 31 JP25 FAN Connector 16 JP36 Bluetooth Connector 32 U40 North Bridge Chipset
Chapter 587 Jumper Board Layout Switch Board Top View Media Board Top View LabelDescription SW1 Arcade/TV tunver switch SW2 Volume Up switch SW3 Volume Down switch SW4 Play/Pause switch SW5 Stop switch SW6 Forward/Next switch SW7 Backward/Previous switch LabelDescription SW1 Power Button SW2 E-mail Button SW3 Internet Button SW4 User Button SW5 E-Power Button
88Chapter 5 Media Board Bottom View LS-2923P Power Board Top View LabelDescription JP3 USB Connector JP2 USB Connector JP6 RF INe Connector JP5 RF Cable Connector JP4 AV IN Connector JP7 Board to Main Board Connector LabelDescription JP1 SIM Card Connector
Chapter 589 Jumper Setting LabelDescription J3 Clear CMOS Jumper Note: J3 locates at bottom side of the main board as the red circle highlighted.