Home > Acer > Notebook > Acer Aspire 4935 Service Guide

Acer Aspire 4935 Service Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Acer Aspire 4935 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Chapter 241
    Exit
    The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.
    The table below describes the parameters in this screen.
    ParameterDescription
    Exit Saving Changes Exit System Setup and save your changes to CMOS.
    Exit Discarding 
    ChangesExit utility without saving setup data to CMOS.
    Load Setup Default Load default values for all SETUP item.
    Discard Changes Load previous values from CMOS for all SETUP items.
    Save Changes Save Setup Data to CMOS.
                 Ins y deH20 Setup Utility Rev 3.5
    Information     Main     A dvanc ed Sec urity Power BootExit
    Item Spec ific  Help
    E x it S aving Changes
    E x it Dis c arding Changes Ex it Sy s tem Setup and 
    Load S etup Defaults s ave y our c hanges  to
    Dis c ard Changes CMOS.
    S ave Changes
    F1 Help           
    ↑↓ Select Item           F5/F6 Change Values            F9 Setup Default
    ESC Exit         
    ←→ S elec t Menu       Enter Select
    XSubMenu    F10 Save and Ex it 
    						
    							42Chapter 2
    BIOS Flash Utilities
    The BIOS flash memory update is required for the following conditions:
    •New versions of system programs
    •New features or options
    •Restore a BIOS when it becomes corrupted. 
    Use the Phlash utility to update the system BIOS flash ROM.
    NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery 
    Diskette before you use the Phlash utility.
    NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
    NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not 
    contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not 
    completely loaded. 
    Fellow the steps below to run the Phlash.
    1.Prepare a bootable diskette.
    2.Copy the flash utilities to the bootable diskette.
    3.Then boot the system from the bootable diskette. The flash utility has auto-execution function. 
    						
    							Chapter 243
    DOS Flash Utility
    Perform the following steps to use the DOS Flash Utility:
    1.Press F2 during boot to enter the Setup Menu.
    2.Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move 
    USB HDD to position 1.
    3.Execute the IFLASH.BAT batch file to update BIOS.
    The flash process begins as shown.
                 InsydeH20 Setup Utility Rev 3.5
    Information     Main     Advanc ed S ec urity P owerBootExit
    Item Spec ific  Help
    B oot priority  order:Us e <
    ↑> or <
    ↓> to select
    a devic e, then pres s
    1. IDE0 : ST9160310AS< F5>  to move it down the
    2. IDE1 : Slimty pe DV D A DS8A 2S lis t, or < F6>  to move 
    3. USB  FFD :  it up the lis t. Pres s
    4. Network  B oot : A theros  Boot A gent < Es c >  to es c ape the menu
    5. US B  HDD : 
    6. US B  CDROM  :
    F1 Help           
    ↑↓ Select Item           F5/F6 Change V alues             F9 Setup Default
    ESC Exit         
    ←→ Select Menu       Enter Select
    XS ubMenu     F10 Save and Ex it 
    						
    							44Chapter 2
    4.In flash BIOS, the message Please do not remove AC Power Source displays.
    NOTE: If the AC power is not connected, the following message displays.
    Plug in the AC power to continue.
    5.Flash is complete when the message Flash programming complete displays. 
    WinFlash Utility
    Perform the following steps to use the WinFlash Utility:
    1.Double click the WinFlash executable.
    2.Click OK to begin the update. A progress screen displays.
    3.When the process is complete, close all programs and applications and reboot the system. 
    						
    							Chapter 245
    Remove HDD/BIOS Password Utilities
    This section provide you with removing HDD/BIOS method:
    Remove HDD Password:
    When the user keys in the wrong password three times, the system reports the following error code to user.
    To unlock the HDD password, perform the following steps:
    1.Press Enter to display the Select Item screen.
    2.Select Enter Unlock Password and press Enter.
    An Unlock Password displays.
    3.Make a note of the key, 76943488 in the example.
    4.Boot up the system and open a DOS prompt.
    5.Enter the UnlockHD.EXE command and input the key to create an unlock code. Make a note of the 
    result, for example 46548274.
    6.Reboot and enter the BIOS by pressing F2 when prompted.
    7.Go to the Security menu and select Set Hdd Password (see “Security” on page 35).
    8.Enter the unlock code generated by UnlockHD.EXE as the current password, 46548274 in the example, 
    and complete the New Password and Confirm fields to create a new HDD password.
    9.Save and exit the BIOS to complete the process. 
    						
    							46Chapter 2
    Removing BIOS Passwords:
    If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the 
    image below.
    To reset the BIOS password, run BIOS_PW.EXE as follows:
    1.
    Key in bios_pw 14452 0
    2.Select one string from the list. 
    						
    							Chapter 247
    3.Reboot the system and key in the selected string (qjjg9vy, 07yqmjd etc.) for the BIOS user 
    password.
    Cleaning BIOS Passwords
    To clear the password, perform the following steps:
    1.From a DOS prompt, Execute clnpwd.exe
    2.Press 1 or 2 to clean the desired password shown on the screen.
    The onscreen message determines whether the function is successful or not. 
    						
    							48Chapter 2
    Miscellaneous Utilities
    Using Boot Sequence Selector
    Boot Sequence Selector allows the boot order to be changes without accessing the BIOS. To use Boot 
    Sequence Selector, perform the following steps:
    1.Enter into DOS.
    2.Execute BS.exe to display the usage screen.
    3.Select the desired boot sequence by entering the corresponding sequence, for example, enter BS2 to 
    change the boot sequence to HDD|CD ROM|LAN|Floppy.
    Using DMITools
    The DMI (Desktop Management Interface) Tool copies BIOS information to eeprom to be used in the DMI pool 
    for hardware management. 
    When the BIOS displays Verifying DMI pool data it is checking the table correlates with the hardware before 
    sending to the operating system (Windows, etc.).
    To update the DMI Pool, perform the following steps:
    1.Enter into DOS.
    2.Execute dmitools. The following messages show dmitools usage:
    •    dmitools /r ==> Read dmi string from memory
    •    dmitools /wm xxxx ==> Write manufacturer name to EEPROM (max. 16 characters)
    •    dmitools /wp xxxx ==> Write product name to EEPROM (max. 16 characters)
    •    dmitools /ws xxxx ==> Write serial number to EEPROM (max. 22 characters)
    •    dmitools /wu xxxx ==> Write uuid to EEPROM (Ignore String)
    •    dmitools /wa xxxx ==> Write asset tag to EEPROM (max. 32 characters)
    NOTE: The following write examples (2 to 5) require a system reboot to take effect
    Example 1: Read DMI Information from Memory
    Input: 
    dmitools /r 
    Output:
    Manufacturer (Type1, Offset04h): Acer
    Product Name (Type1, Offset05h): eMachines xxxxx
    Serial Number (Type1, Offset07h): 01234567890123456789
    UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
    Asset Tag (Type3, Offset04h): Acer Asstag 
    						
    							Chapter 249
    Example 2: Write Product Name to EEPROM
    Input:
    dmitools /wp Acer
    Example 3: Write Serial Number to EEPROM
    Input:
    dmitools /ws 01234567890123456789
    Example 4: Write UUID to EEPROM
    Input:
    dmitools /wu
    Example 5: Write Asset Tag to EEPROM
    Input:
    dmitools /wa Acer Asstag 
    						
    All Acer manuals Comments (0)

    Related Manuals for Acer Aspire 4935 Service Guide