Acer Aspire 4935 Service Guide
Have a look at the manual Acer Aspire 4935 Service Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 720 Acer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Chapter 4161 External Mouse Failure If an external Mouse fails, perform the following actions one at a time to correct the problem. 1.Try an alternative mouse. 2.If the mouse uses a wireless connection, insert new batteries and confirm there is a good connection. See the mouse user manual. 3.If the mouse uses a USB connection, try an alternate USB port. 4.Try an alternative program to verify mouse operation. Reinstall the program experiencing mouse failure. 5.Restart the computer. 6.Remove any recently added hardware and associated software. 7.Remove any recently added software and reboot. 8.Restore system and file settings from a known good date using System Restore. If the issue is not fixed, repeat the preceding steps and select an earlier time and date. 9.Run the Event Viewer to check the events log for errors. For more information see Windows Help and Support. 10.Roll back the mouse driver to the previous version if updated recently. 11 .Remove and reinstall the mouse driver. 12.Check the Device Manager to determine that: •The device is properly installed. There are no red Xs or yellow exclamation marks. •There are no device conflicts. •No hardware is listed under Other Devices. 13.If the Issue is still not resolved, see “Online Support Information” on page 229. Other Failures If the CRT Switch, Dock, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or Volume Wheel fail, perform the following general steps to correct the problem. Do not replace a non-defective FRUs: 1.Check Drive whether is OK. 2.Check Test Fixture is ok. 3.Swap M/B to Try.
162Chapter 4 Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1.Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2.If no error is detected, do not replace any FRU. 3.If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors. Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On Issue” on page 146.): 1.Power-off the computer. 2.Visually check them for damage. If any problems are found, replace the FRU. 3.Remove or disconnect all of the following devices: •Non-Acer devices •Printer, mouse, and other external devices •Battery pack •Hard disk drive •DIMM •CD-ROM/Diskette drive Module •PC Cards 4.Power-on the computer. 5.Determine if the problem has changed. 6.If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. 7.If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU: •System board •LCD assembly
Chapter 4163 POST Codes Tables These tables describe the POST codes and descriptions during the POST. Sec: NO_EVICTION_MODE_DEBUG EQU 1 (CommonPlatform\sec\Ia32\SecCore.inc) Memory: DEBUG_BIOS equ 1 (Chipset\Alviso\MemoryInitAsm\IA32\IMEMORY.INC) CodeDescription 0xC2 MTRR setup 0xC3 Enable cache 0xC4 Establish cache tags 0xC5 Enter NEM, Place the BSP in No Fill mode, set CR0.CD = 1, CR0.NW = 0 0xCF Cache Init Finished CodeDescription 0xA0 First memory check point 0x01 Enable MCHBAR 0x02 Check for DRAM initialization interrupt and reset fail 0x03 Verify all DIMMs are DDR or DDR2 and unbuffered 0x04 Detect an improper warm reset and handle 0x05 Detect if ECC SO-DIMMs are present in the system 0x06 Verify all DIMMs are single or double sided and not asymmetric 0x07 Verify all DIMMs are x8 or x16 width 0x08 Find a common CAS latency between the DIMMS and the MCH 0x09 Determine the memory frequency and CAS latency to program 0x10 Determine the smallest common TRAS for all DIMMs 0x11 Determine the smallest common TRP for all DIMMs 0x12 Determine the smallest common TRCD for all DIMMs 0x13 Determine the smallest refresh period for all DIMMs 0x14 Verify burst length of 8 is supported by all DIMMs 0x15 Determine the smallest tWR supported by all DIMMs 0x16 Determine DIMM size parameters 0x17 Program the correct system memory frequency 0x18 Determine and set the mode of operation for the memory channels 0x19 Program clock crossing registers 0x20 Disable Fast Dispatch 0x21 Program the DRAM Row Attributes and DRAM Row Boundary registers 0x22 Program the DRAM Bank Architecture register 0x23 Program the DRAM Timing & and DRAM Control registers 0x24 Program ODT 0x25 Perform steps required before memory init 0x26 Program the receive enable reference timing control register Program the DLL Timing Control Registers, RCOMP settings
164Chapter 4 BDS & Specific action: 0x27 Enable DRAM Channel I/O Buffers 0x28 Enable all clocks on populated rows 0x29 Perform JEDEC memory initialization for all memory rows 0x30 Perform steps required after memory init 0x31 Program DRAM throttling and throttling event registers 0x32 Setup DRAM control register for normal operation and enable 0x33 Enable RCOMP 0x34 Clear DRAM initialization bit in the SB 0x35 Initialization Sequence Completed, program graphic clocks 0x43 Program Thermal Throttling CodeDescription 0x00 Report the legacy boot is happening 0x12 Wake up the Aps 0x13 Initialize SMM Private Data and relocate BSP SMBASE 0x21 PC init begin at the stage1 0x27 Report every memory range do the hard ware ECC init 0x28 Report status code of every memory range 0x50 Get the root bridge handle 0x51 Notify pci bus driver starts to program the resource 0x58 Reset the host controller 0x5A IdeBus begin initialization 0x79 Report that the remote terminal is being disabled 0x7A Report that the remote terminal is being enabled 0x90 Keyboard reset 0x91 USB Keyboard disable 0x92 Keyboard detection 0x93 Report that the usb keyboard is being enabled 0x94 Clear the keyboard buffer 0x95 Init Keyboard 0x98 Mouse reset 0x99 Mouse disable 0x9A Detect PS2 mouse 0x9B Report that the mouse is being enabled 0xB8 Peripheral removable media reset (ex: IsaFloppy, USB device) 0xB9 Peripheral removable media disable 0xBB Peripheral removable media enable 0xE4 Report Status Code here for DXE_ENTRY_POINT once it is available 0xF8 Report that ExitBootServices() has been called 0xF9 Runtime driver set virtual address map CodeDescription
Chapter 4165 Each PEIM entry point used in 80_PORT Each Driver entry point used in 80_PORT CodeDescription 0x00 0x01 PEI_EVENT_LOG 0xA1 PEI_OEM_SERVICE 0xA2 PEI_SIO_INIT 0xA3 PEI_MONO_STATUS_CODE 0xA4 PEI_CPU_IO_PCI_CFG 0x06 PEI_CPU_IO 0x07 PEI_PCI_CFG 0xA5 PEI_CPU_PEIM 0xA6 PEI_PLATFORM_STAGE1 0xA7 PEI_VARIABLE 0xA8 PEI_SB_INIT 0x0C PEI_CAPSULE 0xAA PEI_PLATFORM_STAGE2 0xAC PEI_SB_SMBUS_ARP_DISABLED 0x0F PEI_HOST_TO_SYSTEM 0x40 PEI_MEMORY_INIT 0x41 PEI_S3_RESUME 0xAD PEI_CLOCK_GEN 0xAB PEI_OP_PRESENCE 0xAE PEI_FIND_FV 0x16 PEI_H2O_DEBUG_IO 0x17 PEI_H2O_DEBUG_COMM 0x16~0x1F PEI_RESERVED 0x20~0x2E PEI_OEM_DEFINED 0xAF PEI_DXE_IPL CodeDescription 0x30 RESERVED 0xB6 DXE_CRC32_SECTION_EXTRACT 0xB8 SCRIPT_SAVE 0xB9 ACPI_S3_SAVE 0xBA SMART_TIMER 0xBB JPEG_DECODER 0xBC PCX_DECODER 0xBE HT_CPU / MP_CPU 0xBF LEGACY_METRONOME 0xC0 FTWLITE 0xC1 RUN_RIME 0xC2 MONOTONIC_COUNTER 0xC3 WATCH_DOG_TIMER
166Chapter 4 0xC4 SECURITY_STUB 0xC5 DXE_CPU_IO 0xC6 CF9_RESET 0xC7 PC_RTC 0xC8 STATUS_CODE 0xC9 VARIABLE EMU_VARIABLE 0xD9 DXE_CHIPSET_INIT 0x45 DXE_ALERT_FORMAT 0xD6 PCI_HOST_BRIDGE 0xD7 PCI_EXPRESS 0xD5 DXE_SB_INIT 0xDA IDE_CONTROLLER 0xDB SATA_CONTROLLER 0xDD SB_SM_BUS 0xE7 ISA_ACPI_DRIVER 0xE8 ISA_BUS 0xE9 ISA_SERIAL 0xED BUS_PCI_UNDI 0xEC PCI_BUS 0xF6 BOOT_PRIORITY 0xF7 FVB_SERVICE 0xF8 ACPI_PLATFORM 0xFB PCI_HOT_PLUG 0xFC DXE_PLATFORM 0xFD PLATFORM_IDE 0x97 SMBIOS 0x98 MEMORY_SUB_CLASS 0x99 MISC_SUB_CLASS 0x82 CON_PLATFORM 0x83 SAVE_MEMORY_CONFIG 0x84 ACPI_SUPPORT 0x85 CON_SPLITTER_UGA_VGA / CON_SPLITTER 0x88 VGA_CLASS 0x89 DATA_HUB 0x60 DISK_IO 0x8B MEMORY_TEST 0x62 CRISIS_RECOVERY 0x8D LEGACY_8259 0x8E LEGACY_REGION 0x8F LEGACY_INTERRUPT 0x70 BIOS_KEYBOARD 0x71 BIOS_VEDIO CodeDescription
Chapter 4167 0x72 MONITER_KEY 0x73 LEGACY_BIOS 0x75 LEGACY_BIOS_PLATFORM 0x76 PCI_PLATFORM 0x6C ISA_FLOOPY 0x6D PS2_MOUSE 0x6E USB_BOT 0x6F USB_CBI0 0x74 USB_MOUSE 0xFA SETUP_UTILITY 0x90 FW_BLOCK_SERVICE 0x78 SMM_USB_LEGACY 0x86 GRAPHICS_CONSOLE 0x87 TERMINAL 0x8A DATA_HUB_STD_ERR 0x7C FAT 0x7D PARTITION 0x7E ENGLISH 0x7F FRENCH 0x9E HII_DATABASE 0x9F OEM_SETUP_BROWSER 0x8C OEM_BADGING_SUPPORT 0xF9 SETUP_MOUSE 0x72 MONITOR_KEY 0xBD PLATFORM_BDS 0x8D RESERVED 0x8E RESERVED 0x8F RESERVED 0xA0 DXE_H2O_DEBUG_IO 0xB3 DXE_TPM_TCG 0xB4 DXE_TPM_PHYSICAL_PRESENCE 0xB7 DXE_OEM_SERVICE 0x9B DXE_ SECURITY_HDD_PASSWORD_SERVICE 0xA9 DXE_LAN_IDER_CONTROLLER 0x9C DXE_ SECURITY_SYSTEM_PASSWORD_SERVICE 0x9D DXE_ SECURITY_ PASSWORD_CONSOLE 0xCB DXE_ DATA_HUB_RECORD_POLICY 0xB5 DXE_TPM_DRIVER 0x11 CHINESE 0xB0 JAPANESE 0xB1 DXE_UNICODE_COLLACTION CodeDescription
168Chapter 4 Each SmmDriver entry point used in 80_PORT CodeDescription 0xD4 SMM_ACCESS 0xDE SMM_CONTROL 0xCC SMM_BASE 0xD2 SMM_RUNTIME 0xDF SB_SMM_DISPATCH 0xD0 SMM_THUNK 0xCA SMM_ACPI_SW_CHILD 0xFE SMM_PLATFORM 0xD8 SMM_GMCH_MBI 0x90 SMM_FW_BLOCK_SERVICE 0x91 SMM_VARIABLE 0x92 SMM_IHISI 0x93 SMM_INT15_MICROCODE 0x94 SMM_PNP 0x95 SMM_INIT_PPM 0xD3 SMM_OEM_SERVICE
Chapter 5169 Jumper and Connector Locations Top View ItemPinDescriptionItemPinDescription 1 JPJ1 RJ-45 Connector 15 JP16 FP Board Connector 2 LED5 AC-IN LED 16 JP23 Keyboard Connector 3 LED10 AC-IN-LED 17 JP26 Function Board Connector 4 LED3 ON-OFF LED 18 JP25 e-Key Board Connector 5 LED4 ON-OFF LED 19 JP22 Media Console Connector 6 SW3 Switch 20 JP15 USB Board Connector 7 LED6 ON-OFF LED 21 JMINI1 MiniCard Port 8 LED7 Media LED 22 JP18 Bluetooth Connector 9 LED8 Num LED 23 JMDC1 MDC Connector 10 LED9 Caps LED 24 SW2 Switch 11 JP13 MIC Connector 25 LED2 Battery LED 12 JLVDS1 LVDS Connector 26 LED1 Power LED 13 JP14 Speaker Connector 27 SW1 Switch 14 JP21 TP Board Connector 28 JEXP1 ExpressCard Connector 3 7 611 23 8 22 28 2 5 9 10 18 19 26 412 13 1415 17 20 21 2425 27 1 16 Chapter 5
170Chapter 5 Bottom View ItemPinDescriptionItemPinDescription 1 JDIMM2 DDR2 Socket 13 JCRT1 D-Sub Connector 2 PJP2 Battery Connector 14 JP17 eSATA/USB Port 3 JDIMM1 DDR2 Socket 15 JHDMI1 HDMI Port 4 U11 VRAM Chip 16 JUSB1 USB Port 5 U9 VRAM Chip 17 JHP1 Headphone Jack 6 U2 Northbridge 18 JMIC1 Microphone Jack 7 U17 VGA NB9M 19 JLINE1 Audio-in Jack 8 JCPU1 CPU Socket 20 IR1 Infrared Sensor 9 U23 Southbridge 21 JREAD1 Card Reader 10 JP27 Fan Connector 22 JMINI2 MiniCard Socket 11 PJP3 DC-IN Connector 23 JSATA1 HDD Connector 12 JPJ1 RJ-45 Connector 24 JSATA2 ODD Connector 2 3 6 4 11 21 8 2022 24 1 57 9 10 12 13 14 15 16 17 18 19 23