Acer Aspire 4730zg Service Guide

							Chapter 371
15.Remove the upper cover by lifting upward from the chassis, rear edge first.
16.Turn the upper cover over. The upper cover appears as follows.
NOTE: Avoid pulling on the cables directly to prevent damage to the connectors.
NOTE: Use the pull-tabs on the FFC cables whenever available to prevent damage to the FFC cables. Release the securing latches and disconnect E as shown. 
						

							72Chapter 3
Removing the Touch Pad Bracket
1.See “Removing the Upper Cover” on page 68.
2.Disconnect the Touch Pad cable from the Touch Pad board. 
						

							Chapter 373
3.Move the Finger Print Reader FFC cable out of the way to prevent damage.
 
4.Remove the two securing screws from the Touch Pad bracket.
5.Remove the Touch Pad bracket.
IMPORTANT:The Touch Pad cannot be removed individually. To replace the Touch Pad, replace the entire 
Upper Cover.
StepSizeQuantityScrew Type
Touch Pad Bracket M2*3 (NL) 2 
						

							74Chapter 3
Removing the Finger Print Reader
1.See “Removing the Upper Cover” on page 68.
2.Remove the securing screw from the Finger Print Reader board.
3.Remove the Finger Print Reader board from the Upper Cover. 
						

							Chapter 375
Removing the Launch Board
1.See “Removing the Upper Cover” on page 68.
2.Remove the two screws from the Launch Board.
 
3.Remove the Launch Board from the Upper Cover. 
 
StepSizeQuantityScrew Type
Launch Board M2*3 (NL) 2 
						

							76Chapter 3
Removing the Speaker Module
1.See “Removing the Upper Cover” on page 68.
2.Remove the adhesive tape from the speaker cable.
3.Remove the four screws holding the Speaker Module in place.
 
StepSizeQuantityScrew Type
Speaker M2*3 (NL) 4 
						

							Chapter 377
4.Remove the Speaker Module from the upper cover.  
						

							78Chapter 3
Removing the Switch Board
1.See “Removing the Upper Cover” on page 68.
2.Ensure the Switch Board cable is free from any obstructions.
3.Turn the Upper Cover. Remove the Switch Board as shown. 
						

							Chapter 379
Removing the Touch Pad Board
IMPORTANT:The Touch Pad board is integrated into the design of the Upper Cover. To replace the Touch Pad 
board, remove all components from the Upper Cover and install an entirely new Upper Cover.
IMPORTANT:The MOSFET pad is attached to the Upper Cover and is reusable. If the replacement Upper 
Cover does not have a MOSFET pad (see highlighted area below), remove the MOSFET pad from 
the replaced Upper Cover and stick it to the new Upper Cover. 
1.See “Removing the Battery Pack” on page 44.
2.See “Removing the SD dummy card” on page 45.
3.See “Removing the ExpressCard dummy card” on page 46.
4.See “Removing the Lower Covers” on page 47.
5.See “Removing the DIMM Modules” on page 49.
6.See “Removing the WLAN Module” on page 50.
7.See “Removing the Hard Disk Drive Module” on page 52.
8.See “Removing the Optical Drive Module” on page 55.
9.See “Removing the Keyboard” on page 61.
10.See “Removing the LCD Module” on page 66.
11 .See “Removing the Upper Cover” on page 68.
12.See “Removing the Touch Pad Bracket” on page 72.
13.See “Removing the Finger Print Reader” on page 74.
14.See “Removing the Launch Board” on page 75.
15.See “Removing the Speaker Module” on page 76.
16.See “Removing the Switch Board” on page 78. 
						

							80Chapter 3
Removing the I/O Board
1.See “Removing the Upper Cover” on page 68.
2.Remove the securing screw from the I/O Board.
3.Lift the I/O Board clear of the Lower cover.
StepSizeQuantityScrew Type
I/O Board M2.5*5 (NL) 1